Link to the AMA?

I forced p=0 video Precision Xoc utilizing the KBoost button which can be seen highlighted in the benchmarks using your algo.

I didn't do this until half way through bc I wanted to make sure that yours was at p0 when it started and wasn't as concerned with the others.

As for the flags I'm not sure, but I know upon entering benching with your algo p0 was definitely enabled and clock was pinged at 2100.  It only dropped slightly under load and settled at the shown 2050.  Now, this is the same level achieved across the board pretty much even with p0 not enabled.

Remember as well I'm using a 1080ti, not 1070 for these benches. I'm not sure I can p0 it under full load with +400-500mem without fragging instantly or losing performance significantly.  On both my FTW3 air, SC2 Air and SC2 Hybrid, I can get a max of about +115-120core and +300, maybe stretching to +350 but for zero sum gains.

I tried this and had an entire thesis of the tweaking and benching done, and my rig crashed the second I hit preview on the post.

Not once did it crash during testing, only trying to post.

So now, cliffs:

I tested this in place of the original hsrminer.exe supplied by miningpoolhub's also switching program, then rebenched all Neoscrypt algo's I have installed on my gaming rig (tested on here first vs taking my 2x1080ti 4x1070 rig down to bench for an a couple hours)

System - Ryzen 1800X @ 4.1 GHz (Corsair H115i Pro), Gigabyte AX370-Gaming 5 Mobo, 16GB Corsair LPX DDR-3200, Samsung 960 EVO NVME 120GB
GPU - EVGA 1080Ti SC2 Hybrid - Stock BIOS - Corsair SP120MM Fans Push/Pull Set @ 100% - NVidia Drivers 390.77 (set at prefer max performance):

All benched starting at 110% pwr, +110-115 core, +200 memory

Klaust/Nanashi/Tpruvot Algos - All max between 1,500 - 1,552 kH/s @ 2050 MHz
Just a miner HSRminer MOD - Max 1,507.47 kH/s @ 2050 MHz
Excavator (nicehash default) - Max 1,925.32 kH/s @ 2,037 MHz (Eventually peaking @ 1,985 MHz while hashing)


Benchresult #1 of 5- Klaust/Nanashi max @ 1,552 kH/s


Benchresult #2 of 5- Klaust/Nanashi/Tpruvot max @ 1,552 kH/s, Excavator max @ 1,899 kH/s


Benchresult #3 of 5- Klaust/Nanashi/Tpruvot max @ 1,552 kH/s, Excavator max @ 1,899 kH/s
Just A Miner (HSRminer.exe) MOD - max 1,507.47 kH/s @ 2050 MHz


Benchresult #4 of 5- Klaust/Nanashi/Tpruvot max @ 1,552 kH/s, Excavator max @ 1,899 kH/s
Just A Miner (HSRminer.exe) MOD - max 1,507.47 kH/s & 1,495.03 kH/s


Benchresult #5 of 5- Excavator (nicehash default) Finalbench - 1,925.32 kH/s @ 2,037 MHz

dutch,

The problem here is, you appear to be criticizing MPH's "website" quite harshly.  I.e.  ...  

I think the website and FAQ is not very comprehensive, as i may say so....  (contrite eh?)

For now, the website is so incredible horrific to me that i cant even find where i have put my wallet adress...

Am i the only one that thinks this site is unclear and horrific chaotic??  ....


I'll give you the benefit of the doubt and go with my gut instinct that your primary language isn't English, as your grammatical structure and quite horrific chaotic; and that you're very new to how pools/transacting between the mining phase>pool wallet>exchange wallet works.


What Sean is trying to say, is that you're here criticizing MPH's website, using an advanced ~$3.5k ASIC machine, asking about stratum port 12xxx and complaining that you lost your wallet address? ... WTF?


You're criticizing a popular and well supported pool, using your big league ~$3.5k hardware, and asking major league questions; yet it's painfully obvious that you're playing at a little league level.

Someone with the big league hardware you're using wouldn't be asking these kind of questions, nor would someone with that hardware need a nice looking website to set it up the worker and ASIC operation well.

Next time try forming questions along with expressing your misunderstanding, maybe keeping the criticisms to yourself...  Or try reading more, maybe different pools, to where you can navigate one line MPH without being so lost.

BTW
I started mining with NH literally 14 days ago with a single GPU in my gaming rig, then tried MPH, gained understanding there and via other pools and exchanges; THEN built a separate 6x1080Ti GPU rig, now customizing MPM command lines and using hub workers to multi algo mine and pay out to multiple wallets and coins.  Crawl-->walk, then you get to criticize.

In regards to your question; I honestly cannot even understand exactly what you are asking.  Do you simply want to see the "status" of your algo switching worker?  Do you not see funds being transferred to your external litecoin wallet?  Have you clicked on the Litecoin link on MPH's website (https://litecoin.miningpoolhub.com/), then tried clicking Dashboard/Wallet/Workers and see if anything is there?

subscribed.  1 month mining and looking to expand horizons (from nh now that i'm building an actual 6x1080ti rig).  thanks for all the helpful info so far.