As a pool I use Ethermine.
Rigs in farm.
RTX 3060 Ti FHR
RTX 3060 Ti LHR
RTX 3070 FHR
RTX 3080 FHR
RX5600 XT
RX5700 XT
RX580 8GB
RX6700
RX6800

Any recommendations on specific settings would be appreciated.

I really appraise TBM efforts and hope you'll become the next big thing.
Since all the mentioned options vastly change the behavior of a RIG, could you mention recommended settings for all the mainstream cards or recommended low and high values  for different cards along with how a setting changes the behavior of the card?

This is my config

-d -K 1 --dagintensity 1 --xintensity 284 -a ethash -H eu1.ethermine.org -p 4444 -r 40 -y 20 -t 120 -W ETH_WALLET -w $rigName -P x --maintenance-wallet MAINTENANCE_WALLET --maintenance-percent 5


As I understood dagintensity should be lower in higher clocks. Has this changed in new version?

Just saw that 1.35 is available is SMOS.
I gave it a try in a 8 x 3060 Ti FHR RIG. Same config as 1.32.
Reported hashrate in SMOS is lower. 437.xx MH/s in 1.32 went to 415.xx MH/s in 1.35.
The thing is that poolside it now seems more correct since 1.32 reported 437.xx MH/s was never the same as current or average.
Tried 1.33 and had the same results as 1.35.

Was the 1.32 and previous versions over reporting the hashrate or is it something else? My cards have gone sub 60 MH/s now and I don't like it.

Understood. I'll wait for v 1.34 to be released in SMOS.

Exact same settings on same 7 x 3060 TI FHR with TBM v 1.32 and v 1.33. Running at -450 Core clock, 2400 Memory clock and 130W power limit.
Getting lower hashrate on 1.33, switched back to 1.32. Running SMOS with nv470.74 drivers.

-d -K 1 --dagintensity 1 --xintensity 284 -a ethash -H eu1.ethermine.org -p 4444 -r 40 -y 20 -t 120 -W "MAIN_WALLET" -w $rigName -P x --maintenance-wallet "MAINTENANCE_WALLET" --maintenance-percent 5

RIG is online >24H.

TBM 1.32 reports 437,xx MH/s.
I keep seeing wrong reported values (pool side). Reported hashrate on MAIN_WALLET is full rigs capacity not the 95% of it (as it should) and it fully correlates with what TBM is saying (437,xx MH/s). Reported hashrate on MAINTENANCE_WALLET remains 2,5 MH/s stable.
Average hashrate in MAIN_WALLET is low. It's about 380 - 384 MH/s. Average hashrate on MAINTENANCE_WALLET is between 18-22 MH/s.

So, 2 issues here.
One is the wrong reported values in MAIN and MAINTENANCE wallets respectively.
Two is the lower overall real hashrate than the reported one.

As a side note if you have any recommendations about my config they are most than welcome.
I manage a total of 10 GH/s in mixed AMD and NVIDIA rigs and I would like to switch them all in TBM as long as it is as stable and fast as other miners. My only reason for switching is the implementation of the maintenance fee since this is exactly the feature I want to get easily paid for my maintenance work.

Managed to get TBM 1.32 to run in SMOS.

Some notices. I'm currently testing TBM 1.32 with a 7 x 3060 Ti FHR. SMOS 5.10.60-sm1#021 nvidia drivers 470.74. Was running t-rex-v0.24.8 with same SMOS and Nvidia versions. With TBM I had to slightly lower my mem overclock, it was crashing all the time. Even with lower mem overclock rig restarts about 20 times per day.
Only reason I switched is the "maintenance-fee" feature. It works but it has room to grow.
My config: -d -a ethash -H eu1.ethermine.org -p 4444 -r 40 -y 20 -t 120 -W "ETH_WALLET1" -w $rigName -P x --maintenance-wallet "ETH_WALLET2" --maintenance-percent 10
(Note on config for SMOS: If you don't put "-d" you don't get any MHs status in SMOS. SMOS puts a persistent message in console telling you to put "-b" to see stats. If you put "-b" you're telling TBM to run only with AMD cards. Not cool when you only have Nvidia cards in your rig... So don't put "-b" to see stats, put "-d")

Ethermine reported hashrate in "ETH_WALLET1" is the full rig's speed not the 90% of the rig's full speed as it should (since the maintenance fee is 10%). In "ETH_WALLET2" it only reports 2,4 MHs, should be 10% of the total hashrate.
Below numbers are after 9 hours running straight without a reboot.
Reported hashrate in both SMOS and Ethermine "ETH_WALLET1" is about 433 MHs, Current is 373 MHs and Average is 306 MHs.
Reported hashrate in Ethermine "ETH_WALLET2" is 2,4MHs, Current is 35.8MHs and Average is 28.4 MHs. 
As you can see by the numbers Current and Average are way off. Even if we take that Average needs more than 9 hours online to stabilize, Current should be very close but it's not. About 24 MHs are missing. Any ideas?

It seems that all my config was wrong.
I now run this config:

-b -a ethash -H stratum+tcp://eu1.ethermine.org -p 4444 -r 40 -y 20 -t 120 -W "ETH_WALLET" -w $rigName -P x --maintenance-wallet "ETH_WALLET" --maintenance-percent 10

It starts ok but I get

00:00:00 [2021-12-10 16:13:41.336] No GPU devices available on platform 0 (Advanced Micro Devices, Inc.)
00:00:00 [2021-12-10 16:13:41.336] No devices are set

This rig has 8 * RTX3070
...

Any idea?

Thank you for that.

Good day.

I was looking for a miner that has the "maintenance fee" feature or something similar and stumbled upon TBM. I found out about the "maintenance fee" option through the changelog of Simple Mining.  
Unfortunately I couldn't find any documentation in TBM site's or on your github page on the exact commands for setting this up.
With a bit looking around I thought I found how the command should be written but it doesn't work.

Running teamblackminer-v1.31-cuda11.4 in SMOS,

-a ethash -o stratum+tcp://eu1.ethermine.org:4444 -u "ETH_WALLET" -w $rigName -p x --maintainance-wallet "ETH_WALLET" --maintainance-percent 5 --worker-name $rigName --miningtime 100 --script-crash reboot.sh

I get /root/miner/teamblackminer-v1.31-cuda11.4/TBMiner: unrecognized option '--maintainance-wallet'

Any help?

Trying to set up your miner and have a look.

The jce_cn_gpu_miner64.exe is identified as "Win64/Packed.Enigma.Q" by ESET. "Enigma" and "trojan" are 2 things I want my computer far away from.
I know that all mining software give false positives but having an alert from my antivirus for a known trojan that encrypted everything and asked for ransom is not a pretty site.

Any inputs on this?

Any idea why http://stellite.cryptonight-pool.eu shows 912.21 KH/s as Network speed and http://cryptoknight.cc/stellite/ shows 5.03 MH/s ??

Δυστυχώς. Για κάποιο λόγο το Coinbase άλλαξε description ως business entity και από "Υπηρεσίες Επιχειρήσεων" το έκαναν "Χρηματιστές" οπότε και κάνει trigger τα capital control rules. 

Thank you for your prompt answer!

1) I can achieve that by enabling auto switch and then disable mining from the wallet page for the coins that I do not want to mine?
2) Round progress is always (at least all the times I've checked) above 100%. Actually well over 120% reaching 170%. SO I should get a lot of coins but unfortunately this was not the case.

Hello,

New to H2C and I like the whole concept. Had my L3+ on Prohashing for quite some time now and wanted to try your service.
Of course it defers from PH in a basic matter as to the payout. H2C pays in whatever coin you mine as PH pays out in whatever coins you choose as payout.(Of course you know all that).

I have a few questions:
 
1) Let's say I choose autoswitch so I can mine the most profitable (at any given time) coin. At the end of the day I will end up having small balances of X different coins. Let's say I want to keep Verge. Do I have to send all that to a number of the different exchanges that are listed under "Balances" in "Market" column, make the trade x coin to BTC (or eth or...) make another trade from BTC (or eth or..) to Verge and then send all my Verge balances to my wallet address?

2) I've been mining in H2C for a bit more than 24H now for XVG only. I keep an eye on it and according to User mining stats I should be getting from 200 to 400 coins per day. My balance is a bit more than 100 coins. Please advise!