Hi People,
I have two S1's. The first one has been running for a month and I got the second yesterday, fired the 2nd one last night and its fan runs full speed straight from power up.
Done all the usual stuff like re-seat cables, Reset button for 10+ sec, Factory default, multiple power supplies etc. I can access the webpage and configure everything okay (Network, Miners, NTP, Pools) but when checking the Status page Summary and Pools looks normal but AntMiners has nothing in it. When looking at the LED's, the functioning S1 has 2 x Green and 1 x Red on the controller and 1 x Green on each hashing board - the problem child has 1 x green (closest one to fan) and 1 x red.
When comparing the two S1's Kernel Logs there are a couple of entries missing from the problematic unit. The following lines are from (Top) the working S1 and lines after are from the problem unit. Differences that exist on the working unit are highlighted.
[ 5.830000] hash ok
[ 5.830000] hashtest OK
[ 5.830000] bitmain-asic: success to register device
[ 5.840000] usbcore: registered new interface driver bitmainbl
[ 5.850000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.860000] ehci-platform: EHCI generic platform driver
[ 5.860000] ehci-platform ehci-platform: EHCI Host Controller
[ 5.870000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 5.870000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 5.900000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 5.900000] hub 1-0:1.0: USB hub found
[ 5.900000] hub 1-0:1.0: 1 port detected
[ 6.240000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 6.390000] hub 1-1:1.0: USB hub found
[ 6.390000] hub 1-1:1.0: 2 ports detected
[ 6.680000] usb 1-1.1: new full-speed USB device number 3 using ehci-platform
[ 6.810000] bitmain 1-1.1:1.0: USB Bitmain asic device now attached to USB Bitmain asic-0
[ 6.820000] PIC microchip usb OK
[ 5.820000] hash ok
[ 5.820000] hashtest OK
[ 5.820000] bitmain-asic: success to register device
[ 5.830000] usbcore: registered new interface driver bitmainbl
[ 5.840000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.850000] ehci-platform: EHCI generic platform driver
[ 5.850000] ehci-platform ehci-platform: EHCI Host Controller
[ 5.860000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 5.870000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 5.890000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 5.890000] hub 1-0:1.0: USB hub found
[ 5.890000] hub 1-0:1.0: 1 port detected
[ 6.230000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 6.380000] hub 1-1:1.0: USB hub found
[ 6.380000] hub 1-1:1.0: 2 ports detected
Can I assume from this the controller board is buggered ?
Cheers,
xcode.