 Show Posts
|
|
Pages: [1] 2 »
|
|
going down :/
got my investment back x2 and have 90% of what i bought left. hoooooooold
|
|
|
|
|
Do I have to update my wallet today or was it pushed untill the 25th?
|
|
|
|
|
Instamined or not. It's still pretty much the only new altcoin that brought us something new and useful.
|
|
|
|
|
After we went into daylight saving time, my wallet wont sync. Also get an error saying the wallet wont work as it should if my date and time are set wrong on my computer.
I get this message on a lot of different wallets but everyone of them will sync, except DRK.
whyyyyyyyyyyy
|
|
|
|
WTF  March 10th I made a transfer of 5700 mzc to my Cryptsy account. I have been on vacation since then and now, when I logged onto my Cryptsy account my MZC balance was 0. I opened my wallet and let it sync up, and yeah, the transfer is made 5700 MZC has been drawn from my wallet. Checked the adress 10 times and it is the right one. Transaction details says 0 confirmations. Checked the block explorer and cant find my transfer there?? Adress: MJ1YF5jvV6Vd9s7p5ArwatxAafEgeAMDvf Where the f*ck is my coins?  |
|
|
|
WTF March 10th I made a transfer of 5700 mzc to my Cryptsy account. I have been on vacation since then and now, when I logged onto my Cryptsy account my MZC balance was 0. I opened my wallet and let it sync up, and yeah, the transfer is made 5700 MZC has been drawn from my wallet. Checked the adress 10 times and it is the right one. Transaction details says 0 confirmations. Checked the block explorer and cant find my transfer there?? Adress: MJ1YF5jvV6Vd9s7p5ArwatxAafEgeAMDvf Where the f*ck is my coins? |
|
|
|
|
Started getting my workers banned when mining the profit switching. Shares above target and bam, banned.
Works just fine mining their dedicated AUR pool tho... weird
|
|
|
|
|
I have located my problem now. (Antminer shuts down after a couple of seconds)
After a few hard resets its clear the problem is the wifi.
Every time I have set the wifi up the Antminer shuts down, and keeps shutting down untill a new har reset is done.
Anyone know why?
Im in contact with Bitmain but it usually takes a few days for an answer.
And yes, I need the wifi to work.
thanks
|
|
|
|
f your PSU and antminer turn on fine, then the PS-ON jumper isnt the issue (assuming it isnt randomly wiggling loose, but then it would cycle on and off a LOT!
sounds like the issue is your antminer if multiple PSUs cause the issue, but im not sure why. try switching the control board to the secondary hashing board and run only that side of the unit.
also, take a multimeter and measure the voltage at the screw terminals. if its outside of 11.8-12.3V you could be having issues
You didn't correct jumpstart your PSU. Buy a PSU tester and plug it into the motherboard cable with 24 pin and your problem is solved OR read a tutorial how to jumpstart a PSU the right way. Thanks for the replys. What I forgot to add was that it was running fine for a couple of days before it started to do this. Any links around for properly jumpstarting a PSU? |
|
|
|
My Antminer shuts down after like 20 seconds. I have tried everything I can think of. Tried all wires I can think of to connect the green and black wires. Tried paper clip and whatnot. Tried running only 1 blade. Tried cutting the green&black wires and connecting that way. Tried several PSUs from 650 to 1250W Anyone? |
|
|
|
|
Hi.
I have just build my first rig and ran in to some problems.
First I tried it out with just 1 GPU and everything worked fine.
But when I add another or 3 more GPUs the rig will start up, all the fans on all the GPUs will work fine but I cant get any signal to my monitor.
Tried the MBs HDMI and all the GPUs HDMI and still nothing.
What is causing this?
Its 4x Gigabyte R9 280X on a Gigabyte z87x-ud3h mobo.
Anyone?
|
|
|
|
|
Im fucking retarded I cant setup this shit.
Ip-Config:
Wireless LAN adapter Wi-Fi 2:
Connection-specific DNS Suffix . : glocalnet.net
Link-local IPv6 Address . . . . . : fe80::e9a2:6455:bad0:ffc6%1x
IPv4 Address. . . . . . . . . . . : 92.32.217.24x
Subnet Mask . . . . . . . . . . . : 255.255.255.19x
Default Gateway . . . . . . . . . : 92.32.217.19x
What I changed the TCP/IPV4 w/e on my computer in order to access my Antminer
IPv4 Address. . . . . . . . . . . : 192.168.1.25x
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.1
Then I connected my ethernet cable to my laptop and logged into my miner using its IP.
NOW
What should my WAN settings be ?
Nothing works
|
|
|
|
Reboot. It might hang. Then power off and on again. Then log in
Tried it several times :/ After you reboot and login, go to the network tab and verify that the wireless is being issued an IP. This is the info from my Network page. Any ideas? SystemHostname antMiner Model TP-Link TL-WR743N/ND v2 Firmware Version OpenWrt Barrier Breaker r38031 / LuCI Trunk (svn-r9909) Kernel Version 3.10.12 Local Time Mon Dec 2 06:09:09 2013 Uptime 1h 41m 22s Load Average Network
IPv4 WAN Statuseth1 Type: static Address: 192.168.1.241 Netmask: 255.255.255.0 Gateway: 92.32.217.20x DNS 1: 8.8.8.8 Connected: 1h 33m 8s Active Connections 593 / 16384 (3%)
DHCP Leases-empty- WirelessGeneric 802.11bgn Wireless Controller (radio0) [Signal: -75 dBm / Noise: -94 dBm] 50% SSID: GN_private_6x Mode: Client Channel: 11 (2.462 GHz) Bitrate: 1 Mbit/s BSSID: 00:01:38:89:FB:C6 Encryption: WEP Open System (WEP-40) Associated Stations MAC-Address 00:01:38:89:FX:X6 Network Client "GN_private_6x" Signal -75 dBm Noise -94 dBm RX Rate 1.0 Mbit/s, MCS 0, 20MHz TX Rate 1.0 Mbit/s, MCS 0, 20MHz |
|
|
|
Reboot. It might hang. Then power off and on again. Then log in
Tried it several times :/ |
|
|
|
|
My Antminer wont mine..
I finally got it to connect to my wifi, but it wont start mining. I have tried several pools but it wont start.
When I add my pool-info the 'Applying changes' info is stuck at '/etc/config/cgminer ' is this a problem? The pool-info seems to change fine anyway.
Also changed the NTP-server IPs as someone suggested.
plzzzzz halp
|
|
|
|
I have powered up my miner and connected the ethernet-cable to my laptop. But I cant access the Antminer via its IP. Whats wrong? Edit; I followed this ( https://bitcointalk.org/index.php?topic=344970.0) guide at first, changing the network settings and w/e. But now I se other guides that just connect miner and pc and then just type in the IP in the browser to access the miner. Now nothing works.. Grin привет The default gateway on the miner is I believe 192.168.1.1 Most of the latest miners shipped with the ip address 192.168.1.99 So got to your network adapter settings (NOT the wifi the LAN adapter) and change your IPv4 settings to: IP address: 192.168.1.254 Subnet: It will be set automatically Default Gateway: 192.168.1.1 Then type your miners IP in your browser Thank you, nice and easy! |
|
|
|
I have powered up my miner and connected the ethernet-cable to my laptop. But I cant access the Antminer via its IP. Whats wrong? Edit; I followed this ( https://bitcointalk.org/index.php?topic=344970.0) guide at first, changing the network settings and w/e. But now I se other guides that just connect miner and pc and then just type in the IP in the browser to access the miner. Now nothing works.. Grin |
|
|
|
I have powered up my miner and connected the ethernet-cable to my laptop. But I cant access the Antminer via its IP. Whats wrong? Edit; I followed this ( https://bitcointalk.org/index.php?topic=344970.0) guide at first, changing the network settings and w/e. But now I se other guides that just connect miner and pc and then just type in the IP in the browser to access the miner. Now nothing works.. Grin |
|
|
|
I have powered up my miner and connected the ethernet-cable to my laptop. But I cant access the Antminer via its IP. Whats wrong? Edit; I followed this guide at first, changing the network settings and w/e. But now I se other guides that just connect miner and pc and then just type in the IP in the browser to access the miner. Now nothing works..  |
|
|
|
I've got 1 miner stuck in India.  |
|
|
|
|
