why BTG verry low sols Lolminer VS  Gminer

6x gtx 1060   Lolminer  120 Sols  and Gminer 210 sols ??

LolMiner 1.87 updated!
- Changelog -
Fishhash: Significantly improved speed on AMD RX 470 - RX 590 series of gpus (by 30%), significantly improved speed on Nvidia CMP 170HX (by 8-9%)
Fishhash: Implemented new DAG build procedure for Nvidia Turing and up gpus, that will build a valid DAG even on higher memory OC. This significantly reduces the number of defect shares in this situation.
Pyrin: Improved Pyrin performance on Nvidia Turing and newer gpus by about 2%
Ton / Gram: Improved performance on Nvidia Turing and newer gpus by about 1-2%
Improved performance of Fishhash + Pyrin dual mining on Nvidia Turing and newer gpus by about +10% on the Pyrin side
Improved performance of Fishhash + Alephium dual mining on Nvidia Ampere and newer gpus by about -2% speed on Fishhash side, but +10% on Alephium side with auto tune, about +5% on Alephium side at same Fishhash speed with manual tuning
Added experimental support for Fishash + Gram / Ton dual mining for AMD Vega and VII GPUs. Might require manual setting of dual tuning ratio.
The Ton job interface can now connect to pools or bridges using Ton mode 5 with http, so not enforcing https.
Removed Blake3-Ironfish from visible algorithms. --algo IRONFISH will now redirect to FISHHASH.
Fixed a bug causing the display of defect shares when mining Ton / Gram with very high difficulty
Fixed missing of Ton / Gram mining on AMD Tonga, AMD Fiji and RX 460 (Baffin) series of GPU. Was accidentally removed in a previous release.



https://github.com/Lolliedieb/lolMiner-releases/releases/tag/1.87

 5x 1060 6gb Algo Ethashb3 Rethereum Teamblackminer 101 MHS vs Rigelminer   115 MHS


Why  Teamblackminer   Verry verry SLOW

srbminer-multi 2.3.6 updated!
- Changelog -
Added support for algorithm 'dynex' on NVIDIA GPUs
Performance improvement on algorithm 'dynex' on AMD GPUs
Removed Dynex optimised dual kernels
Lowered devfee for algorithm 'ETHASHB3'  to standard 0.85%

teamblackminer 2.01 updated!
- Changelog -
Faster miner startup.
Reduced stales in the vertcoin,etchash,ethash,ethashb3,zil and kawpow algo.
Fixed rejected shares bug in the vertcoin algo.
EthashB3   devfee Rethereum   Nvidia   0.5%

Why this mining software very very slow !!!!!!!!!!!!!!!

Lowest Devfee bat Very Slow 5 x gtx 1060 6gb 390 watt  108 MHS
on https://rth.crazypool.org/ you can use evry eth mining software to mining RTH ethashB3
teamblackminer 2.00 updated!
- Changelog -
Added support for EthashB3 on nvidia (The ethereum restart project) Rethereum. 0.5% fee



Ethereum Miner  5 x gtx 1060 6gb 390 watt  112,5 MHS  0.0 Zero Fee
NFSMiner v1.3   5 x gtx 1060 6gb 390 watt  113,1 MHS   No stinking fee 0.0 Zero Fee

you can look this pool https://rth.crazypool.org/#/ works with any Ethereum mining software !!!!

RTH Ethashb3 Mining

Claymore miner works fine  112 mhs low devfee
Phoenixminer 0.65 Devfee
Teamredminer 1.00 Devfee
Teamblackminer 0.5 Devfee
Lolminer         1.00 Devfee
Miniz miner 107 Mhs 1.00 Devfee
T-rex miner      1.00 Devfee
Gminer            0.65 Devfee with Old version
NBminer           0.70
SBminer           0.50
Ethminer  112 MHS 0.0 Zero Devfee
Retminer V2  108 MHS     0.00 Devfee
NfsMiner v1.3  102 Mhs  0.00 No stinking Devfee !!!!!!

please best reth mining software rigel or

rigelminer 1.4.4 zil time dont work any more only zil (?) why and what is the problem,

and many many stale schares !!!!!!!

To much stale shares rigelminer 1.4.4 with 3 x miners on Ironfisch coin with high stale schares why dev ?

rigelminer 1.4.3 vs lolminer 1.74 with ironfisch coin, lolminer is a bit faster than rigelminer 1.4.3 and with rigelminer you also have a lot of stale shares unfortunately, if possible please solve the problem with stale shears please dev

i tested rigel 1.4.1 and rigel 1.3.9 with same miner 5x gtx 1060  with nexa and zill but rigel 1.4.1  is much slower then rigel 1.3.9 and uses more power why dev ?

Hello rigel dev, I am using rigelminer 1.3.9 this is the fastest miner on nexo + zil coin, on the same miner I also tried the Rigel 1.3.11 and Rigel 1.3.12 Rigel 1.4.0 but uses more power and a lot slower unfortunately, that's why do I stick with Rigel 1.3.9 is te best and fastest mining software version

why is the rigelminer 1.3.9 with 5 x gtx 1060 on lolminer 1.70 29mhs and on rigelminer 44.5Mhs is much faster than lolminer 1.70 same configuration on afterburner with Nexa coin mining

Test Nexa Hashrate (Rigel Miner vs Bzminer vs lolMiner) -   https://youtu.be/es6icyj8hNQ


 

i use Tt miner for nexa and zil   program with zil sitcher   https://github.com/Pashnov/zil_switcher

rigel 1.3.6 updated! and rigel dont needed a zil switcher  program  to mining nexa and zil
- Changelog -
(Nexa) Minor performance improvements
(Nexa) Fix performance regression for 40xx GPUs

Hello good day evrybody ,i tested latest version ttminer and rigel 1.35 nexa coin and zil dual mining on the same miner and rigelminer 1.35 is much faster than TTminer .

oke thanks fort the quic answer ,why no adding nexa coin ?

Why is the screen off TT-Miner very animated screenshot , The Rigel miner version is very stable screen .
why you can the tt-miner dev make same screen

us this swither  zil and nexa https://github.com/Pashnov/zil_switcher