Hi correct power supply.
When I do usb-devices with it plugged in get below. So Pi is fine, Pi usb is fine, correct power supply tried a few usb cables which work (so not these). Power to unit is on, power to fan is on, just nothing from chips.

T:  Bus=01 Lev=02 Prnt=02 Port=03 Cnt=02 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0403 ProdID=6015 Rev=10.00
S:  Manufacturer=FTDI
S:  Product=FT232EX
C:  #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=98mA
I:  If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)


T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480 MxCh= 1
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev=05.10
S:  Manufacturer=Linux 5.10.11-v7+ dwc_otg_hcd
S:  Product=DWC OTG Controller
S:  SerialNumber=3f980000.usb
C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#=0x0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480 MxCh= 5
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=02 MxPS=64 #Cfgs=  1
P:  Vendor=0424 ProdID=9514 Rev=02.00
C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=2mA
I:  If#=0x0 Alt= 1 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=02 Driver=hub

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0424 ProdID=ec00 Rev=02.00
C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=2mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=ff Driver=smsc95xx

T:  Bus=01 Lev=02 Prnt=02 Port=03 Cnt=02 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0403 ProdID=6015 Rev=10.00
S:  Manufacturer=FTDI
S:  Product=FT232EX
C:  #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=98mA
I:  If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)

Yep usb on Pi works recognises newpac no problem. The mini usb port on 909 seems fine, everything connected and tight stumped

thanks for suggestions.

Hi @ n0nce, tried cg miner several times, works for newpac, get nothing for the 909


no sign of the 909

thanks

Sorry new here, posted in wrong place.

The blue leds are around the fan, the fan and the lights are both working though.

So its not the Pi or the Pi usb port, just plugged in a newpac and set it going, hashing no problem. So has to be something on the 909

thanks all

Tried turning on and off, no use  . Been running it on Pi3b will get a laptop and download everything and see if the problem is the same there. In the meantime, where would I find the log files to see if anything happened.

Thank you

Hi Everyone,
Wonder if anyone has any ideas. Got mine a few weeks ago was hashing no problem. Came home today zero hashing. Fan is on, with blue light. Red light on front is on but zero hashing, no blinking white light and no activity on solopool??

HI I hope you are well.
I was hoping for some help/ info. I am new at this.
I purchased 2 moonlanders 2 Iand  have managed to get my two Moonlanders going using your instructions (they are running on a Pi 3 externally powered hub) and i can monitor them.
So far I have tried to mine nyancoin from multiple pools and also XVG.
When I first execute the BFGMiner  i get them mining with  thered led flashing, however, within a minute or two the difficulty on the block goes up and my moonlanders seem to stop mining, green led ok, no red led I have tried the lower difficulty ports on the sites and I have tried changing the difficulty in the start shell script too.

Do you have any ideas?? Are they still mining or have they been frozen out. Is there a work around.

any info would be great

these are cool little machines

thanks