Show Posts
|
Pages: [1]
|
Can you please connect a fully working hash board to the controller port J5?
If it is working ok, then I would say that the control board is ok. And that there is one faulty hash board.
Well, I conneted a faultiboard to J6 connector and error apears now in [Chain6]. Hasboard is the problem so.
|
|
|
Now connected, J7 and J6, works?? . . [ 30.603875] xemacps e000b000.ps7-ethernet: link up (1000/FULL) This is XILINX board. Totalram: 507527168 Detect 512MB control board of XILINX DETECT HW version=0008c510 miner ID : 80641d2e2420881c Miner Type = S9 AsicType = 1387 real AsicNum = 63 use critical mode to search freq... get PLUG ON=0x000000c0 Find hashboard on Chain[6] Find hashboard on Chain[7] set_reset_allhashboard = 0x0000ffff Check chain[6] PIC fw version=0x03 Check chain[7] PIC fw version=0x03 chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] has freq in PIC, will disable freq setting. chain[6] has freq in PIC and will jump over... Chain[6] has core num in PIC Chain[6] ASIC[39] has core num=1 Check chain[6] PIC fw version=0x03 chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] has freq in PIC, will disable freq setting. chain[7] has freq in PIC and will jump over... Chain[7] has core num in PIC Chain[7] ASIC[37] has core num=1 Check chain[7] PIC fw version=0x03 get PIC voltage=125 on chain[6], value=870 get PIC voltage=6 on chain[7], value=940 set_reset_allhashboard = 0x00000000 chain[6] temp offset record: 62,0,0,0,0,0,35,28 chain[6] temp chip I2C addr=0x98 chain[6] has no middle temp, use special fix mode. chain[7] temp offset record: 62,0,0,0,0,0,35,28 chain[7] temp chip I2C addr=0x98 chain[7] has no middle temp, use special fix mode. set_reset_allhashboard = 0x0000ffff set_reset_allhashboard = 0x00000000 CRC error counter=0 set command mode to VIL
--- check asic number After Get ASIC NUM CRC error counter=0 set_baud=0 The min freq=700 set real timeout 52, need sleep=379392 After TEST CRC error counter=0 set_reset_allhashboard = 0x0000ffff set_reset_allhashboard = 0x00000000 search freq for 1 times, completed chain = 2, total chain num = 2 set_reset_allhashboard = 0x0000ffff set_reset_allhashboard = 0x00000000 restart Miner chance num=2 waiting for receive_func to exit! waiting for pic heart to exit! bmminer not found= 1373 root 0:00 grep bmminer
bmminer not found, restart bmminer ... This is user mode for mining Detect 512MB control board of XILINX Miner Type = S9 Miner compile time: Fri Nov 17 17:57:49 CST 2017 type: Antminer S9set_reset_allhashboard = 0x0000ffff set_reset_allhashboard = 0x00000000 set_reset_allhashboard = 0x0000ffff miner ID : 80641d2e2420881c set_reset_allhashboard = 0x0000ffff Checking fans!get fan[2] speed=4560 get fan[2] speed=4560 get fan[2] speed=4560 get fan[2] speed=4560 get fan[2] speed=4560 get fan[2] speed=4560 get fan[2] speed=4560 get fan[2] speed=4560 get fan[2] speed=4560 get fan[5] speed=6120 get fan[2] speed=4560 get fan[5] speed=6120 get fan[2] speed=4560 get fan[5] speed=6120 chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] Detect: use voltage limit rules on single board! Detect: S9_63 use voltage level=1 : 1 Chain[J7] has backup chain_voltage=870 Check chain[6] PIC fw version=0x03 chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] Detect: use voltage limit rules on single board! Detect: S9_63 use voltage level=1 : 1 Chain[J8] has backup chain_voltage=870 Check chain[7] PIC fw version=0x03 Chain[J7] orignal chain_voltage_pic=125 value=870 Chain[J8] orignal chain_voltage_pic=6 value=940 Chain[J8] will use backup chain_voltage_pic=870 [125] Chain[J8] get working chain_voltage_pic=125 set_reset_allhashboard = 0x0000ffff set_reset_allhashboard = 0x00000000 Chain[J7] has 63 asic Chain[J8] has 63 asic Chain[J7] has core num in PIC Chain[J7] ASIC[39] has core num=1 Chain[J8] has core num in PIC Chain[J8] ASIC[37] has core num=1 miner total rate=9335GH/s fixed rate=9000GH/s read PIC voltage=940 on chain[6] Chain:6 chipnum=63 Chain[J7] voltage added=0.0V Chain:6 temp offset=0 Chain:6 base freq=650 Asic[ 0]:650 Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650 Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650 Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650 Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650 Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650 Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650 Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650 Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650 Chain:6 max freq=650 Chain:6 min freq=650
read PIC voltage=940 on chain[7] Chain:7 chipnum=63 Chain[J8] voltage added=0.0V Chain:7 temp offset=0 Chain:7 base freq=650 Asic[ 0]:650 Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650 Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650 Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650 Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650 Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650 Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650 Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650 Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650 Chain:7 max freq=650 Chain:7 min freq=650
Miner fix freq ... read PIC voltage=940 on chain[6] Chain:6 chipnum=63 Chain[J7] voltage added=0.0V Chain:6 temp offset=0 Chain:6 base freq=650 Asic[ 0]:650 Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650 Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650 Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650 Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650 Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650 Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650 Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650 Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650 Chain:6 max freq=650 Chain:6 min freq=650
read PIC voltage=940 on chain[7] Chain:7 chipnum=63 Chain[J8] voltage added=0.0V Chain:7 temp offset=0 Chain:7 base freq=650 Asic[ 0]:650 Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650 Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650 Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650 Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650 Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650 Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650 Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650 Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650 Chain:7 max freq=650 Chain:7 min freq=650
max freq = 650 set baud=1 Chain[J7] PIC temp offset=62,0,0,0,0,0,35,28 chain[6] temp chip I2C addr=0x98 chain[6] has no middle temp, use special fix mode. Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55 New offset Chain[6] chip[244] local:23 remote:26 offset:26 Chain[J7] chip[244] get middle temp offset=26 typeID=55 Chain[J8] PIC temp offset=62,0,0,0,0,0,35,28 chain[7] temp chip I2C addr=0x98 chain[7] has no middle temp, use special fix mode. Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55 New offset Chain[7] chip[244] local:23 remote:26 offset:26 Chain[J8] chip[244] get middle temp offset=26 typeID=55 Chain[J7] set working voltage=870 [125] Chain[J8] set working voltage=870 [125] do heat board 8xPatten for 1 times start send works on chain[6] start send works on chain[7] get send work num :57456 on Chain[6] get send work num :57456 on Chain[7] wait recv nonce on chain[6] wait recv nonce on chain[7] get nonces on chain[6] require nonce number:912 require validnonce number:57456 asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912 asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=912 asic[15]=912 asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912 asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912 asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912 asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912 asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912 asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
freq[00]=650 freq[01]=650 freq[02]=650 freq[03]=650 freq[04]=650 freq[05]=650 freq[06]=650 freq[07]=650 freq[08]=650 freq[09]=650 freq[10]=650 freq[11]=650 freq[12]=650 freq[13]=650 freq[14]=650 freq[15]=650 freq[16]=650 freq[17]=650 freq[18]=650 freq[19]=650 freq[20]=650 freq[21]=650 freq[22]=650 freq[23]=650 freq[24]=650 freq[25]=650 freq[26]=650 freq[27]=650 freq[28]=650 freq[29]=650 freq[30]=650 freq[31]=650 freq[32]=650 freq[33]=650 freq[34]=650 freq[35]=650 freq[36]=650 freq[37]=650 freq[38]=650 freq[39]=650 freq[40]=650 freq[41]=650 freq[42]=650 freq[43]=650 freq[44]=650 freq[45]=650 freq[46]=650 freq[47]=650 freq[48]=650 freq[49]=650 freq[50]=650 freq[51]=650 freq[52]=650 freq[53]=650 freq[54]=650 freq[55]=650 freq[56]=650 freq[57]=650 freq[58]=650 freq[59]=650 freq[60]=650 freq[61]=650 freq[62]=650
total valid nonce number:57456 total send work number:57456 require valid nonce number:57456 repeated_nonce_num:0 err_nonce_num:26639 last_nonce_num:29040 get nonces on chain[7] require nonce number:912 require validnonce number:57456 asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912 asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=912 asic[15]=912 asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912 asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912 asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912 asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912 asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912 asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
freq[00]=650 freq[01]=650 freq[02]=650 freq[03]=650 freq[04]=650 freq[05]=650 freq[06]=650 freq[07]=650 freq[08]=650 freq[09]=650 freq[10]=650 freq[11]=650 freq[12]=650 freq[13]=650 freq[14]=650 freq[15]=650 freq[16]=650 freq[17]=650 freq[18]=650 freq[19]=650 freq[20]=650 freq[21]=650 freq[22]=650 freq[23]=650 freq[24]=650 freq[25]=650 freq[26]=650 freq[27]=650 freq[28]=650 freq[29]=650 freq[30]=650 freq[31]=650 freq[32]=650 freq[33]=650 freq[34]=650 freq[35]=650 freq[36]=650 freq[37]=650 freq[38]=650 freq[39]=650 freq[40]=650 freq[41]=650 freq[42]=650 freq[43]=650 freq[44]=650 freq[45]=650 freq[46]=650 freq[47]=650 freq[48]=650 freq[49]=650 freq[50]=650 freq[51]=650 freq[52]=650 freq[53]=650 freq[54]=650 freq[55]=650 freq[56]=650 freq[57]=650 freq[58]=650 freq[59]=650 freq[60]=650 freq[61]=650 freq[62]=650
total valid nonce number:57456 total send work number:57456 require valid nonce number:57456 repeated_nonce_num:0 err_nonce_num:26627 last_nonce_num:33868 chain[6]: All chip cores are opened OK! Test Patten on chain[6]: OK! chain[7]: All chip cores are opened OK! Test Patten on chain[7]: OK! setStartTimePoint total_tv_start_sys=141 total_tv_end_sys=142 restartNum = 2 , auto-reinit enabled... do read_temp_func once... do check_asic_reg 0x08
get RT hashrate from Chain[6]: (asic index start from 1-63) Asic[01]=121.618 Asic[02]=113.984 Asic[03]=116.165 Asic[04]=115.444 Asic[05]=117.474 Asic[06]=115.444 Asic[07]=116.534 Asic[08]=116.198 Asic[09]=116.819 Asic[10]=117.591 Asic[11]=115.125 Asic[12]=119.990 Asic[13]=116.014 Asic[14]=513.164 Asic[15]=115.712 Asic[16]=114.588 Asic[17]=118.044 Asic[18]=115.293 Asic[19]=400.203 Asic[20]=118.984 Asic[21]=119.554 Asic[22]=112.558 Asic[23]=118.145 Asic[24]=113.548 Asic[25]=116.752 Asic[26]=119.604 Asic[27]=117.893 Asic[28]=116.886 Asic[29]=131.617 Asic[30]=118.413 Asic[31]=111.383 Asic[32]=118.128 Asic[33]=111.753 Asic[34]=114.487 Asic[35]=116.198 Asic[36]=265.801 Asic[37]=119.621 Asic[38]=120.108 Asic[39]=114.504 Asic[40]=116.081 Asic[41]=115.477 Asic[42]=119.135 Asic[43]=115.964 Asic[44]=114.739 Asic[45]=664.595 Asic[46]=118.044 Asic[47]=116.568 Asic[48]=1559.01 Asic[49]=112.273 Asic[50]=116.048 Asic[51]=115.695 Asic[52]=120.712 Asic[53]=116.886 Asic[54]=117.541 Asic[55]=117.255 Asic[56]=118.279 Asic[57]=128.731 Asic[58]=115.561 Asic[59]=115.225 Asic[60]=115.527 Asic[61]=116.500 Asic[62]=115.125 Asic[63]=121.701
get RT hashrate from Chain[7]: (asic index start from 1-63) Asic[01]=117.289 Asic[02]=112.692 Asic[03]=113.514 Asic[04]=110.628 Asic[05]=116.182 Asic[06]=111.904 Asic[07]=114.638 Asic[08]=116.819 Asic[09]=116.668 Asic[10]=114.252 Asic[11]=114.588 Asic[12]=115.997 Asic[13]=112.558 Asic[14]=484.727 Asic[15]=114.420 Asic[16]=111.702 Asic[17]=116.870 Asic[18]=114.118 Asic[19]=114.907 Asic[20]=114.001 Asic[21]=117.776 Asic[22]=111.635 Asic[23]=252.547 Asic[24]=110.343 Asic[25]=114.823 Asic[26]=116.266 Asic[27]=114.286 Asic[28]=113.212 Asic[29]=131.533 Asic[30]=114.403 Asic[31]=109.672 Asic[32]=112.357 Asic[33]=111.333 Asic[34]=111.132 Asic[35]=115.578 Asic[36]=114.336 Asic[37]=117.172 Asic[38]=116.282 Asic[39]=112.122 Asic[40]=628.944 Asic[41]=111.316 Asic[42]=119.621 Asic[43]=116.081 Asic[44]=114.621 Asic[45]=114.856 Asic[46]=119.168 Asic[47]=116.098 Asic[48]=1466.46 Asic[49]=108.833 Asic[50]=113.044 Asic[51]=114.370 Asic[52]=116.584 Asic[53]=114.051 Asic[54]=116.198 Asic[55]=115.175 Asic[56]=376.245 Asic[57]=127.741 Asic[58]=113.195 Asic[59]=118.178 Asic[60]=112.407 Asic[61]=214.714 Asic[62]=111.971 Asic[63]=118.749 Check Chain[J7] ASIC RT error: (asic index start from 1-63) Asic[01]=121.618000 Asic[02]=113.984000 Asic[03]=116.165000 Asic[04]=115.444000 Asic[05]=117.474000 Asic[06]=115.444000 Asic[07]=116.534000 Asic[08]=116.198000 Asic[09]=116.819000 Asic[10]=117.591000 Asic[11]=115.125000 Asic[12]=119.990000 Asic[13]=116.014000 Asic[14]=513.164000 Asic[15]=115.712000 Asic[16]=114.588000 Asic[17]=118.044000 Asic[18]=115.293000 Asic[19]=400.203000 Asic[20]=118.984000 Asic[21]=119.554000 Asic[22]=112.558000 Asic[23]=118.145000 Asic[24]=113.548000 Asic[25]=116.752000 Asic[26]=119.604000 Asic[27]=117.893000 Asic[28]=116.886000 Asic[29]=131.617000 Asic[30]=118.413000 Asic[31]=111.383000 Asic[32]=118.128000 Asic[33]=111.753000 Asic[34]=114.487000 Asic[35]=116.198000 Asic[36]=265.801000 Asic[37]=119.621000 Asic[38]=120.108000 Asic[39]=114.504000 Asic[40]=116.081000 Asic[41]=115.477000 Asic[42]=119.135000 Asic[43]=115.964000 Asic[44]=114.739000 Asic[45]=664.595000 Asic[46]=118.044000 Asic[47]=116.568000 Asic[48]=1559.010000 Asic[49]=112.273000 Asic[50]=116.048000 Asic[51]=115.695000 Asic[52]=120.712000 Asic[53]=116.886000 Asic[54]=117.541000 Asic[55]=117.255000 Asic[56]=118.279000 Asic[57]=128.731000 Asic[58]=115.561000 Asic[59]=115.225000 Asic[60]=115.527000 Asic[61]=116.500000 Asic[62]=115.125000 Asic[63]=121.701000 Check Chain[J8] ASIC RT error: (asic index start from 1-63) Asic[01]=117.289000 Asic[02]=112.692000 Asic[03]=113.514000 Asic[04]=110.628000 Asic[05]=116.182000 Asic[06]=111.904000 Asic[07]=114.638000 Asic[08]=116.819000 Asic[09]=116.668000 Asic[10]=114.252000 Asic[11]=114.588000 Asic[12]=115.997000 Asic[13]=112.558000 Asic[14]=484.727000 Asic[15]=114.420000 Asic[16]=111.702000 Asic[17]=116.870000 Asic[18]=114.118000 Asic[19]=114.907000 Asic[20]=114.001000 Asic[21]=117.776000 Asic[22]=111.635000 Asic[23]=252.547000 Asic[24]=110.343000 Asic[25]=114.823000 Asic[26]=116.266000 Asic[27]=114.286000 Asic[28]=113.212000 Asic[29]=131.533000 Asic[30]=114.403000 Asic[31]=109.672000 Asic[32]=112.357000 Asic[33]=111.333000 Asic[34]=111.132000 Asic[35]=115.578000 Asic[36]=114.336000 Asic[37]=117.172000 Asic[38]=116.282000 Asic[39]=112.122000 Asic[40]=628.944000 Asic[41]=111.316000 Asic[42]=119.621000 Asic[43]=116.081000 Asic[44]=114.621000 Asic[45]=114.856000 Asic[46]=119.168000 Asic[47]=116.098000 Asic[48]=1466.460000 Asic[49]=108.833000 Asic[50]=113.044000 Asic[51]=114.370000 Asic[52]=116.584000 Asic[53]=114.051000 Asic[54]=116.198000 Asic[55]=115.175000 Asic[56]=376.245000 Asic[57]=127.741000 Asic[58]=113.195000 Asic[59]=118.178000 Asic[60]=112.407000 Asic[61]=214.714000 Asic[62]=111.971000 Asic[63]=118.749000 Done check_asic_reg do read temp on Chain[6] Chain[6] Chip[62] TempTypeID=55 middle offset=26 Chain[6] Chip[62] local Temp=49 Chain[6] Chip[62] middle Temp=58 Special fix Chain[6] Chip[62] middle Temp = 64 Done read temp on Chain[6] do read temp on Chain[7] Chain[7] Chip[62] TempTypeID=55 middle offset=26 Chain[7] Chip[62] local Temp=50 Chain[7] Chip[62] middle Temp=59 Special fix Chain[7] Chip[62] middle Temp = 65 Done read temp on Chain[7] read_temp_func Done! CRC error counter=0
I don't stand why now work, and some hours before no.
|
|
|
Hi HagssFIN, I due, equal results: [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017 [ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Xilinx Zynq [ 0.000000] cma: CMA: reserved 128 MiB at 16800000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 126976 [ 0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000 [ 0.000000] Normal zone: 992 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 126976 pages, LIFO batch:31 [ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768 [ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125984 [ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc06d1374 (6949 kB) [ 0.000000] .init : 0xc06d2000 - 0xc0705380 ( 205 kB) [ 0.000000] .data : 0xc0706000 - 0xc074cf78 ( 284 kB) [ 0.000000] .bss : 0xc074cf84 - 0xc078d9fc ( 259 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] ps7-slcr mapped to df802000 [ 0.000000] zynq_clock_init: clkc starts at df802100 [ 0.000000] Zynq clock init [ 0.000014] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns [ 0.000309] ps7-ttc #0 at df804000, irq=43 [ 0.000618] Console: colour dummy device 80x30 [ 0.000650] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328) [ 0.040211] pid_max: default: 32768 minimum: 301 [ 0.040432] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.040452] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.042584] CPU: Testing write buffer coherency: ok [ 0.042915] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.042973] Setting up static identity map for 0x4c4b00 - 0x4c4b58 [ 0.043199] L310 cache controller enabled [ 0.043218] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB [ 0.121036] CPU1: Booted secondary processor [ 0.210230] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.210362] Brought up 2 CPUs [ 0.210380] SMP: Total of 2 processors activated. [ 0.210388] CPU: All CPU(s) started in SVC mode. [ 0.211051] devtmpfs: initialized [ 0.213465] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.214684] regulator-dummy: no parameters [ 0.222345] NET: Registered protocol family 16 [ 0.224576] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.226874] cpuidle: using governor ladder [ 0.226888] cpuidle: using governor menu [ 0.234324] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered [ 0.235850] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.235864] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.235977] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000 [ 0.257692] bio: create slab <bio-0> at 0 [ 0.259117] vgaarb: loaded [ 0.259815] SCSI subsystem initialized [ 0.260913] usbcore: registered new interface driver usbfs [ 0.261112] usbcore: registered new interface driver hub [ 0.261348] usbcore: registered new device driver usb [ 0.261882] media: Linux media interface: v0.10 [ 0.262046] Linux video capture interface: v2.00 [ 0.262287] pps_core: LinuxPPS API ver. 1 registered [ 0.262299] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.262430] PTP clock support registered [ 0.262785] EDAC MC: Ver: 3.0.0 [ 0.263846] Advanced Linux Sound Architecture Driver Initialized. [ 0.266705] DMA-API: preallocated 4096 debug entries [ 0.266719] DMA-API: debugging enabled by kernel config [ 0.266792] Switched to clocksource arm_global_timer [ 0.287904] NET: Registered protocol family 2 [ 0.288559] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.288617] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.288701] TCP: Hash tables configured (established 4096 bind 4096) [ 0.288747] TCP: reno registered [ 0.288764] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.288795] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.289027] NET: Registered protocol family 1 [ 0.289381] RPC: Registered named UNIX socket transport module. [ 0.289393] RPC: Registered udp transport module. [ 0.289401] RPC: Registered tcp transport module. [ 0.289410] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.289422] PCI: CLS 0 bytes, default 64 [ 0.289853] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available [ 0.291862] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.293946] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.294140] msgmni has been set to 967 [ 0.294925] io scheduler noop registered [ 0.294938] io scheduler deadline registered [ 0.294991] io scheduler cfq registered (default) [ 0.307189] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208 [ 0.307210] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16 [ 0.432988] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps [ 1.001244] console [ttyPS0] enabled [ 1.005510] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000 [ 1.013154] [drm] Initialized drm 1.1.0 20060810 [ 1.030227] brd: module loaded [ 1.039612] loop: module loaded [ 1.049221] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k [ 1.054972] e1000e: Copyright(c) 1999 - 2013 Intel Corporation. [ 1.063072] libphy: XEMACPS mii bus: probed [ 1.067647] ------------- phy_id = 0x3625e62 [ 1.072385] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54 [ 1.081026] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.087679] ehci-pci: EHCI PCI platform driver [ 1.094894] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing? [ 1.101709] usbcore: registered new interface driver usb-storage [ 1.108578] mousedev: PS/2 mouse device common for all mice [ 1.114667] i2c /dev entries driver [ 1.121624] zynq-edac f8006000.ps7-ddrc: ecc not enabled [ 1.127200] cpufreq_cpu0: failed to get cpu0 regulator: -19 [ 1.133081] Xilinx Zynq CpuIdle Driver started [ 1.137959] sdhci: Secure Digital Host Controller Interface driver [ 1.144054] sdhci: Copyright(c) Pierre Ossman [ 1.148464] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.154191] mmc0: no vqmmc regulator found [ 1.158232] mmc0: no vmmc regulator found [ 1.196831] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA [ 1.205526] usbcore: registered new interface driver usbhid [ 1.211046] usbhid: USB HID core driver [ 1.215762] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda [ 1.222052] nand: Micron MT29F2G08ABAEAWP [ 1.226023] nand: 256MiB, SLC, page size: 2048, OOB size: 64 [ 1.231972] Bad block table found at page 131008, version 0x01 [ 1.238210] Bad block table found at page 130944, version 0x01 [ 1.244258] 3 ofpart partitions found on MTD device pl353-nand [ 1.250030] Creating 3 MTD partitions on "pl353-nand": [ 1.255131] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel" [ 1.263189] 0x000002000000-0x00000b000000 : "angstram-rootfs" [ 1.270504] 0x00000b000000-0x000010000000 : "upgrade-rootfs" [ 1.279477] TCP: cubic registered [ 1.282713] NET: Registered protocol family 17 [ 1.287423] Registering SWP/SWPB emulation handler [ 1.293314] regulator-dummy: disabling [ 1.297651] UBI: attaching mtd1 to ubi0 [ 1.823951] UBI: scanning is finished [ 1.835605] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0 [ 1.842685] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 1.849448] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 1.856112] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 1.862989] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0 [ 1.868970] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 1.876078] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1134783803 [ 1.885120] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40 [ 1.894336] UBI: background thread "ubi_bgt0d" started, PID 1080 [ 1.894342] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 1.898284] ALSA device list: [ 1.898288] No soundcards found. [ 1.914694] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082 [ 1.943698] UBIFS: recovery needed [ 2.042505] UBIFS: recovery completed [ 2.046164] UBIFS: mounted UBI device 0, volume 0, name "rootfs" [ 2.052115] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 2.061221] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs) [ 2.071110] UBIFS: reserved for root: 0 bytes (0 KiB) [ 2.076139] UBIFS: media format: w4/r0 (latest is w4/r0), UUID B079DD56-06BB-4E31-8F5E-A6604F480DB2, small LPT model [ 2.087450] VFS: Mounted root (ubifs filesystem) on device 0:11. [ 2.094858] devtmpfs: mounted [ 2.097983] Freeing unused kernel memory: 204K (c06d2000 - c0705000) [ 2.935918] random: dd urandom read with 0 bits of entropy available [ 3.326829] [ 3.326829] bcm54xx_config_init [ 3.936838] [ 3.936838] bcm54xx_config_init [ 7.937672] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz [ 7.943773] xemacps e000b000.ps7-ethernet: link up (1000/FULL) [ 25.222130] In axi fpga driver! [ 25.225204] request_mem_region OK! [ 25.228626] AXI fpga dev virtual address is 0xdf9fc000 [ 25.233701] *base_vir_addr = 0x8c510 [ 25.249251] In fpga mem driver! [ 25.252321] request_mem_region OK! [ 25.255882] fpga mem virtual address is 0xe2000000 [ 26.056857] [ 26.056857] bcm54xx_config_init [ 26.686843] [ 26.686843] bcm54xx_config_init [ 30.687670] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz [ 30.693773] xemacps e000b000.ps7-ethernet: link up (1000/FULL) This is XILINX board. Totalram: 507527168 Detect 512MB control board of XILINX DETECT HW version=0008c510 miner ID : 80641d2e2420881c Miner Type = S9 AsicType = 1387 real AsicNum = 63 Find /tmp/searcherror: U6:1 The last log is below: This is XILINX board. Totalram: 507527168 Detect 512MB control board of XILINX DETECT HW version=0008c510 miner ID : 80641d2e2420881c Miner Type = S9 AsicType = 1387 real AsicNum = 63 use critical mode to search freq... get PLUG ON=0x000000e0 Find hashboard on Chain[5] Find hashboard on Chain[6] Find hashboard on Chain[7] set_reset_allhashboard = 0x0000ffff Check chain[5] PIC fw version=0x00 chain[5] PIC need restore ... Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5] Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5] Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5] Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5] Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5] Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5] Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5] Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5] After restore: chain[5] PIC fw version=0x00
J6 (Chain 6) only connected seem work fine: [ 25.215585] In fpga mem driver! [ 25.218722] request_mem_region OK! [ 25.222220] fpga mem virtual address is 0xe2000000 [ 26.017029] [ 26.017029] bcm54xx_config_init [ 26.647044] [ 26.647044] bcm54xx_config_init [ 30.647879] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz [ 30.653984] xemacps e000b000.ps7-ethernet: link up (1000/FULL) This is XILINX board. Totalram: 507527168 Detect 512MB control board of XILINX DETECT HW version=0008c510 miner ID : 80641d2e2420881c Miner Type = S9 AsicType = 1387 real AsicNum = 63 use critical mode to search freq... get PLUG ON=0x00000040 Find hashboard on Chain[6] set_reset_allhashboard = 0x0000ffff Check chain[6] PIC fw version=0x03 chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] has freq in PIC, will disable freq setting. chain[6] has freq in PIC and will jump over... Chain[6] has core num in PIC Chain[6] ASIC[39] has core num=1 Check chain[6] PIC fw version=0x03 get PIC voltage=6 on chain[6], value=940 set_reset_allhashboard = 0x00000000 chain[6] temp offset record: 62,0,0,0,0,0,35,28 chain[6] temp chip I2C addr=0x98 chain[6] has no middle temp, use special fix mode. set_reset_allhashboard = 0x0000ffff set_reset_allhashboard = 0x00000000 CRC error counter=0 set command mode to VIL
--- check asic number After Get ASIC NUM CRC error counter=0 set_baud=0 The min freq=700 set real timeout 52, need sleep=379392 After TEST CRC error counter=0 set_reset_allhashboard = 0x0000ffff set_reset_allhashboard = 0x00000000 search freq for 1 times, completed chain = 1, total chain num = 1 set_reset_allhashboard = 0x0000ffff set_reset_allhashboard = 0x00000000 restart Miner chance num=2 waiting for receive_func to exit! waiting for pic heart to exit! bmminer not found= 1364 root 0:00 grep bmminer
bmminer not found, restart bmminer ... This is user mode for mining Detect 512MB control board of XILINX Miner Type = S9 Miner compile time: Fri Nov 17 17:57:49 CST 2017 type: Antminer S9set_reset_allhashboard = 0x0000ffff set_reset_allhashboard = 0x00000000 set_reset_allhashboard = 0x0000ffff miner ID : 80641d2e2420881c set_reset_allhashboard = 0x0000ffff Checking fans!get fan[2] speed=4560 get fan[2] speed=4560 get fan[2] speed=4560 get fan[2] speed=4560 get fan[2] speed=4560 get fan[2] speed=4560 get fan[2] speed=4560 get fan[2] speed=4560 get fan[2] speed=4560 get fan[5] speed=6120 get fan[2] speed=4560 get fan[5] speed=6120 get fan[2] speed=4560 get fan[5] speed=6120 chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] Detect: use voltage limit rules on single board! Detect: S9_63 use voltage level=1 : 1 Chain[J7] has backup chain_voltage=870 Check chain[6] PIC fw version=0x03 Chain[J7] orignal chain_voltage_pic=6 value=940 Chain[J7] will use backup chain_voltage_pic=870 [125] Chain[J7] get working chain_voltage_pic=125 set_reset_allhashboard = 0x0000ffff set_reset_allhashboard = 0x00000000 Chain[J7] has 63 asic Chain[J7] has core num in PIC Chain[J7] ASIC[39] has core num=1 miner total rate=4667GH/s fixed rate=4500GH/s read PIC voltage=940 on chain[6] Chain:6 chipnum=63 Chain[J7] voltage added=0.0V Chain:6 temp offset=0 Chain:6 base freq=650 Asic[ 0]:650 Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650 Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650 Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650 Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650 Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650 Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650 Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650 Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650 Chain:6 max freq=650 Chain:6 min freq=650
Miner fix freq ... read PIC voltage=940 on chain[6] Chain:6 chipnum=63 Chain[J7] voltage added=0.0V Chain:6 temp offset=0 Chain:6 base freq=650 Asic[ 0]:650 Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650 Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650 Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650 Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650 Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650 Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650 Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650 Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650 Chain:6 max freq=650 Chain:6 min freq=650
max freq = 650 set baud=1 Chain[J7] PIC temp offset=62,0,0,0,0,0,35,28 chain[6] temp chip I2C addr=0x98 chain[6] has no middle temp, use special fix mode. Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55 New offset Chain[6] chip[244] local:22 remote:25 offset:26 Chain[J7] chip[244] get middle temp offset=26 typeID=55 Chain[J7] set working voltage=870 [125] do heat board 8xPatten for 1 times start send works on chain[6] do read_temp_func once... do check_asic_reg 0x08 Done check_asic_reg do read temp on Chain[6] Chain[6] Chip[62] TempTypeID=55 middle offset=26 Chain[6] Chip[62] local Temp=29 Chain[6] Chip[62] middle Temp=40 Special fix Chain[6] Chip[62] middle Temp = 44 Done read temp on Chain[6] Set fixed fan speed=70 FAN PWM: 70 read_temp_func Done! CRC error counter=0
|
|
|
Hi, equal problem in my S9 new hardware.(MARCH 2018 bach) Today are aribed and after 30 minutes working weel at 13.5THs, i rebooted and don't work anymore. 3 harsh boards are red led off, some times, reboting the middel board leds are stand red. I have a 2 BITMAIN 1600W PSU equalt results with 2 power supply. Sistem don't run bmminer binary and no has rate. Fans runs at full speed after some seconds of boot and don't decrease speed. Kernel log: [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017 [ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Xilinx Zynq [ 0.000000] cma: CMA: reserved 128 MiB at 16800000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 126976 [ 0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000 [ 0.000000] Normal zone: 992 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 126976 pages, LIFO batch:31 [ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768 [ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125984 [ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc06d1374 (6949 kB) [ 0.000000] .init : 0xc06d2000 - 0xc0705380 ( 205 kB) [ 0.000000] .data : 0xc0706000 - 0xc074cf78 ( 284 kB) [ 0.000000] .bss : 0xc074cf84 - 0xc078d9fc ( 259 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] ps7-slcr mapped to df802000 [ 0.000000] zynq_clock_init: clkc starts at df802100 [ 0.000000] Zynq clock init [ 0.000016] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns [ 0.000313] ps7-ttc #0 at df804000, irq=43 [ 0.000617] Console: colour dummy device 80x30 [ 0.000649] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328) [ 0.040212] pid_max: default: 32768 minimum: 301 [ 0.040432] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.040451] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.042591] CPU: Testing write buffer coherency: ok [ 0.042930] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.042990] Setting up static identity map for 0x4c4b00 - 0x4c4b58 [ 0.043215] L310 cache controller enabled [ 0.043235] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB [ 0.121038] CPU1: Booted secondary processor [ 0.210230] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.210361] Brought up 2 CPUs [ 0.210380] SMP: Total of 2 processors activated. [ 0.210388] CPU: All CPU(s) started in SVC mode. [ 0.211049] devtmpfs: initialized [ 0.213459] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.214669] regulator-dummy: no parameters [ 0.222329] NET: Registered protocol family 16 [ 0.224564] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.226858] cpuidle: using governor ladder [ 0.226872] cpuidle: using governor menu [ 0.234325] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered [ 0.235844] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.235858] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.235972] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000 [ 0.257674] bio: create slab <bio-0> at 0 [ 0.259099] vgaarb: loaded [ 0.259800] SCSI subsystem initialized [ 0.260816] usbcore: registered new interface driver usbfs [ 0.260995] usbcore: registered new interface driver hub [ 0.261255] usbcore: registered new device driver usb [ 0.261796] media: Linux media interface: v0.10 [ 0.261954] Linux video capture interface: v2.00 [ 0.262202] pps_core: LinuxPPS API ver. 1 registered [ 0.262214] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.262337] PTP clock support registered [ 0.262692] EDAC MC: Ver: 3.0.0 [ 0.263742] Advanced Linux Sound Architecture Driver Initialized. [ 0.266580] DMA-API: preallocated 4096 debug entries [ 0.266595] DMA-API: debugging enabled by kernel config [ 0.266671] Switched to clocksource arm_global_timer [ 0.287330] NET: Registered protocol family 2 [ 0.287981] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.288038] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.288123] TCP: Hash tables configured (established 4096 bind 4096) [ 0.288167] TCP: reno registered [ 0.288185] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.288215] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.288462] NET: Registered protocol family 1 [ 0.288765] RPC: Registered named UNIX socket transport module. [ 0.288777] RPC: Registered udp transport module. [ 0.288786] RPC: Registered tcp transport module. [ 0.288794] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.288807] PCI: CLS 0 bytes, default 64 [ 0.289241] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available [ 0.291251] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.293391] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.293575] msgmni has been set to 967 [ 0.294359] io scheduler noop registered [ 0.294373] io scheduler deadline registered [ 0.294420] io scheduler cfq registered (default) [ 0.307123] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208 [ 0.307143] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16 [ 0.429705] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps [ 0.997873] console [ttyPS0] enabled [ 1.002148] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000 [ 1.009797] [drm] Initialized drm 1.1.0 20060810 [ 1.026910] brd: module loaded [ 1.036218] loop: module loaded [ 1.045711] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k [ 1.051696] e1000e: Copyright(c) 1999 - 2013 Intel Corporation. [ 1.059599] libphy: XEMACPS mii bus: probed [ 1.063973] ------------- phy_id = 0x3625e62 [ 1.068933] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54 [ 1.077605] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.084231] ehci-pci: EHCI PCI platform driver [ 1.091511] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing? [ 1.098347] usbcore: registered new interface driver usb-storage [ 1.105180] mousedev: PS/2 mouse device common for all mice [ 1.111317] i2c /dev entries driver [ 1.118272] zynq-edac f8006000.ps7-ddrc: ecc not enabled [ 1.123754] cpufreq_cpu0: failed to get cpu0 regulator: -19 [ 1.129666] Xilinx Zynq CpuIdle Driver started [ 1.134509] sdhci: Secure Digital Host Controller Interface driver [ 1.140688] sdhci: Copyright(c) Pierre Ossman [ 1.144956] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.151780] mmc0: no vqmmc regulator found [ 1.155792] mmc0: no vmmc regulator found [ 1.196690] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA [ 1.205392] usbcore: registered new interface driver usbhid [ 1.210908] usbhid: USB HID core driver [ 1.215607] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda [ 1.221910] nand: Micron MT29F2G08ABAEAWP [ 1.225874] nand: 256MiB, SLC, page size: 2048, OOB size: 64 [ 1.231821] Bad block table found at page 131008, version 0x01 [ 1.238042] Bad block table found at page 130944, version 0x01 [ 1.244091] 3 ofpart partitions found on MTD device pl353-nand [ 1.249874] Creating 3 MTD partitions on "pl353-nand": [ 1.254965] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel" [ 1.263029] 0x000002000000-0x00000b000000 : "angstram-rootfs" [ 1.270367] 0x00000b000000-0x000010000000 : "upgrade-rootfs" [ 1.279321] TCP: cubic registered [ 1.282555] NET: Registered protocol family 17 [ 1.287268] Registering SWP/SWPB emulation handler [ 1.293148] regulator-dummy: disabling [ 1.297496] UBI: attaching mtd1 to ubi0 [ 1.823251] UBI: scanning is finished [ 1.834897] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0 [ 1.841980] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 1.848743] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 1.855407] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 1.862284] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0 [ 1.868265] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 1.875372] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1134783803 [ 1.884415] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40 [ 1.893631] UBI: background thread "ubi_bgt0d" started, PID 1080 [ 1.893636] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 1.897593] ALSA device list: [ 1.897596] No soundcards found. [ 1.914009] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082 [ 1.971287] UBIFS: mounted UBI device 0, volume 0, name "rootfs" [ 1.977250] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 1.986334] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs) [ 1.996241] UBIFS: reserved for root: 0 bytes (0 KiB) [ 2.001278] UBIFS: media format: w4/r0 (latest is w4/r0), UUID B079DD56-06BB-4E31-8F5E-A6604F480DB2, small LPT model [ 2.013019] VFS: Mounted root (ubifs filesystem) on device 0:11. [ 2.020482] devtmpfs: mounted [ 2.023590] Freeing unused kernel memory: 204K (c06d2000 - c0705000) [ 2.862900] random: dd urandom read with 0 bits of entropy available [ 3.256695] [ 3.256695] bcm54xx_config_init [ 3.866740] [ 3.866740] bcm54xx_config_init [ 7.867535] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz [ 7.873641] xemacps e000b000.ps7-ethernet: link up (1000/FULL) [ 25.417709] In axi fpga driver! [ 25.420774] request_mem_region OK! [ 25.424165] AXI fpga dev virtual address is 0xdf9fc000 [ 25.429300] *base_vir_addr = 0x8c510 [ 25.444611] In fpga mem driver! [ 25.447748] request_mem_region OK! [ 25.451255] fpga mem virtual address is 0xe2000000 [ 26.256691] [ 26.256691] bcm54xx_config_init [ 26.886690] [ 26.886690] bcm54xx_config_init [ 30.887535] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz [ 30.893641] xemacps e000b000.ps7-ethernet: link up (1000/FULL) This is XILINX board. Totalram: 507527168 Detect 512MB control board of XILINX DETECT HW version=0008c510 miner ID : 80641d2e2420881c Miner Type = S9 AsicType = 1387 real AsicNum = 63 Find /tmp/searcherror: U6:1 The last log is below: This is XILINX board. Totalram: 507527168 Detect 512MB control board of XILINX DETECT HW version=0008c510 miner ID : 80641d2e2420881c Miner Type = S9 AsicType = 1387 real AsicNum = 63 use critical mode to search freq... get PLUG ON=0x000000e0 Find hashboard on Chain[5] Find hashboard on Chain[6] Find hashboard on Chain[7] set_reset_allhashboard = 0x0000ffff Check chain[5] PIC fw version=0x00 chain[5] PIC need restore ... Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5] Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5] Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5] Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5] Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5] Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5] Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5] Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5] After restore: chain[5] PIC fw version=0x00
|
|
|
|