 Show Posts
|
|
Pages: [1]
|
|
Hi, Thanks for taking the time to respond. I really appreciate it.
A) I changed the board, I assumed that the was the first problem.
B) I then tested the hashboards one by one.
C) All the hashboards work.
To recap: The Fan does is not operating correctly and the hashboards are running hotter than normal. Every time I attempt to apply firmware, it does not hold. However, the S9 still operates, at a low fan speed and about 10 degrees hotter than normal.
|
|
|
|
|
No it was not a tokamak. My Question is, how do i apply the correct firmware and get the S9 to behave normally.
|
|
|
|
Hi all, I'd to start by saying I'm happy to pay for service if someone knows how to fix this issue. I had one of my S9's (13.5 TH) plugged in to 1600W Rosewill PSU. It ran fine for about 4 months. At some point, there was what we are assuming was a power surge. The S9 stopped working. I did some testing and found that the control board seemed to be the issue. I've gone ahead and replaced the control board. It works now - sort of. Issues are as follows: First, when I apply the the AUTO_FREQ fireware update, the hardware version on the system tab is blank and the hashboards do not turn on. I can get the hash board and the device to turn on when I apply the 650m fixed frequency firmware. However, when I go to the miner config tab and apply the Search Frequency From, it doesn't work. The hashboards turn off after a few seconds and the device resets. I've updated everything else on the same tab and its mining but the temps are MUCH HIGHER than avg (99,92,95) this is in a room with normal temp (21 degree Celsius) and the fan speed shows as FAN3=1680 , Fan 4=1680 and Fan 6= 4,440. I have 10 other machines and they dont nearly operate as hot as this ( they are in a room all together with the avg temp at 35 degrees) and the fans only show 2 as operational fan3=6003 and fan6=4,440 I've attached my Kernel Log below. Please ADVISE. Thanks in advance. [ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 16800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 126976
[ 0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125984
[ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06d1374 (6949 kB)
[ 0.000000] .init : 0xc06d2000 - 0xc0705380 ( 205 kB)
[ 0.000000] .data : 0xc0706000 - 0xc074cf78 ( 284 kB)
[ 0.000000] .bss : 0xc074cf84 - 0xc078d9fc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to df802000
[ 0.000000] zynq_clock_init: clkc starts at df802100
[ 0.000000] Zynq clock init
[ 0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000310] ps7-ttc #0 at df804000, irq=43
[ 0.000619] Console: colour dummy device 80x30
[ 0.000651] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[ 0.040211] pid_max: default: 32768 minimum: 301
[ 0.040428] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040447] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.042579] CPU: Testing write buffer coherency: ok
[ 0.042920] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.042980] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[ 0.043204] L310 cache controller enabled
[ 0.043223] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.121036] CPU1: Booted secondary processor
[ 0.210230] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.210364] Brought up 2 CPUs
[ 0.210383] SMP: Total of 2 processors activated.
[ 0.210391] CPU: All CPU(s) started in SVC mode.
[ 0.211054] devtmpfs: initialized
[ 0.213471] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.214685] regulator-dummy: no parameters
[ 0.222362] NET: Registered protocol family 16
[ 0.224657] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.226946] cpuidle: using governor ladder
[ 0.226960] cpuidle: using governor menu
[ 0.234399] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.235924] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.235938] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.236052] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[ 0.257859] bio: create slab <bio-0> at 0
[ 0.259270] vgaarb: loaded
[ 0.259964] SCSI subsystem initialized
[ 0.260977] usbcore: registered new interface driver usbfs
[ 0.261179] usbcore: registered new interface driver hub
[ 0.261399] usbcore: registered new device driver usb
[ 0.261935] media: Linux media interface: v0.10
[ 0.262094] Linux video capture interface: v2.00
[ 0.262341] pps_core: LinuxPPS API ver. 1 registered
[ 0.262353] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.262477] PTP clock support registered
[ 0.262832] EDAC MC: Ver: 3.0.0
[ 0.263908] Advanced Linux Sound Architecture Driver Initialized.
[ 0.266757] DMA-API: preallocated 4096 debug entries
[ 0.266771] DMA-API: debugging enabled by kernel config
[ 0.266844] Switched to clocksource arm_global_timer
[ 0.287861] NET: Registered protocol family 2
[ 0.288509] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.288566] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.288651] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.288695] TCP: reno registered
[ 0.288711] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.288743] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.288980] NET: Registered protocol family 1
[ 0.289330] RPC: Registered named UNIX socket transport module.
[ 0.289343] RPC: Registered udp transport module.
[ 0.289351] RPC: Registered tcp transport module.
[ 0.289359] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.289372] PCI: CLS 0 bytes, default 64
[ 0.289808] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.291833] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.293933] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.294118] msgmni has been set to 967
[ 0.294899] io scheduler noop registered
[ 0.294912] io scheduler deadline registered
[ 0.294953] io scheduler cfq registered (default)
[ 0.306608] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.306627] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.430052] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 0.997681] console [ttyPS0] enabled
[ 1.001925] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[ 1.009556] [drm] Initialized drm 1.1.0 20060810
[ 1.026474] brd: module loaded
[ 1.035854] loop: module loaded
[ 1.045315] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.051461] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.059408] libphy: XEMACPS mii bus: probed
[ 1.063782] ------------- phy_id = 0x3625e62
[ 1.068542] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.077145] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.083768] ehci-pci: EHCI PCI platform driver
[ 1.091030] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.097894] usbcore: registered new interface driver usb-storage
[ 1.104745] mousedev: PS/2 mouse device common for all mice
[ 1.110870] i2c /dev entries driver
[ 1.117872] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.123351] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.129276] Xilinx Zynq CpuIdle Driver started
[ 1.134113] sdhci: Secure Digital Host Controller Interface driver
[ 1.140319] sdhci: Copyright(c) Pierre Ossman
[ 1.144591] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.151416] mmc0: no vqmmc regulator found
[ 1.155427] mmc0: no vmmc regulator found
[ 1.196868] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.205563] usbcore: registered new interface driver usbhid
[ 1.211074] usbhid: USB HID core driver
[ 1.215790] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.222092] nand: Micron MT29F2G08ABAEAWP
[ 1.226055] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.231999] Bad block table found at page 131008, version 0x01
[ 1.238226] Bad block table found at page 130944, version 0x01
[ 1.244274] 3 ofpart partitions found on MTD device pl353-nand
[ 1.250056] Creating 3 MTD partitions on "pl353-nand":
[ 1.255146] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.263180] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.270529] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.279503] TCP: cubic registered
[ 1.282737] NET: Registered protocol family 17
[ 1.287446] Registering SWP/SWPB emulation handler
[ 1.293327] regulator-dummy: disabling
[ 1.297688] UBI: attaching mtd1 to ubi0
[ 1.825891] UBI: scanning is finished
[ 1.837544] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.844601] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.851397] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.858073] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.864911] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 1.870920] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.878032] UBI: max/mean erase counter: 16/8, WL threshold: 4096, image sequence number: 1283732989
[ 1.887148] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[ 1.896346] UBI: background thread "ubi_bgt0d" started, PID 1080
[ 1.896351] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.900289] ALSA device list:
[ 1.900293] No soundcards found.
[ 1.916728] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[ 1.945908] UBIFS: recovery needed
[ 2.882285] UBIFS: recovery completed
[ 2.885964] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 2.891914] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 2.901017] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 2.910906] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 2.915936] UBIFS: media format: w4/r0 (latest is w4/r0), UUID C72F8006-6DFF-46BA-BBE9-380960A89F92, small LPT model
[ 2.927256] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 2.934434] devtmpfs: mounted
[ 2.937578] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[ 3.797880] random: dd urandom read with 0 bits of entropy available
[ 4.186896]
[ 4.186896] bcm54xx_config_init
[ 4.796891]
[ 4.796891] bcm54xx_config_init
[ 7.797710] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 7.803805] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 21.326624] In axi fpga driver!
[ 21.329689] request_mem_region OK!
[ 21.333080] AXI fpga dev virtual address is 0xdf9fc000
[ 21.338219] *base_vir_addr = 0x8c510
[ 21.353857] In fpga mem driver!
[ 21.356986] request_mem_region OK!
[ 21.360491] fpga mem virtual address is 0xe2000000
[ 22.156292]
[ 22.156292] bcm54xx_config_init
[ 22.786220]
[ 22.786220] bcm54xx_config_init
[ 25.786760] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 25.792781] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 500.025340] random: nonblocking pool is initialized
This is XILINX board. Totalram: 507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : 810455825c208814
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[26] has core num=2
Chain[6] ASIC[29] has core num=2
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Chain[7] ASIC[37] has core num=1
Chain[7] ASIC[40] has core num=1
Chain[7] ASIC[42] has core num=7
Chain[7] ASIC[43] has core num=11
Chain[7] ASIC[61] has core num=1
Check chain[7] PIC fw version=0x03
get PIC voltage=91 on chain[5], value=890
get PIC voltage=125 on chain[6], value=870
get PIC voltage=125 on chain[7], value=870
set_reset_allhashboard = 0x00000000
chain[5] temp offset record: 62,0,0,0,0,0,35,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
chain[6] temp offset record: 62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
chain[7] temp offset record: 62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL
--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
search freq for 1 times, completed chain = 3, total chain num = 3
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1376 root 0:00 grep bmminer
bmminer not found, restart bmminer ...
bmminer not found=20786 root 0:00 grep bmminer
bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Fri Nov 17 17:37:49 CST 2017 type: Antminer S9set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 810455825c208814
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[2] speed=6000
get fan[2] speed=6000
get fan[2] speed=6000
get fan[2] speed=6000
get fan[2] speed=6000
get fan[2] speed=6000
get fan[5] speed=4560
get fan[2] speed=6000
get fan[5] speed=4560
get fan[2] speed=6000
get fan[5] speed=4560
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J6] has backup chain_voltage=890
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J7] has backup chain_voltage=870
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J8] has backup chain_voltage=870
Check chain[7] PIC fw version=0x03
Chain[J6] orignal chain_voltage_pic=91 value=890
Chain[J7] orignal chain_voltage_pic=125 value=870
Chain[J8] orignal chain_voltage_pic=125 value=870
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J7] has core num in PIC
Chain[J7] ASIC[26] has core num=2
Chain[J7] ASIC[29] has core num=2
Chain[J8] has core num in PIC
Chain[J8] ASIC[37] has core num=1
Chain[J8] ASIC[40] has core num=1
Chain[J8] ASIC[42] has core num=7
Chain[J8] ASIC[43] has core num=11
Chain[J8] ASIC[61] has core num=1
miner total rate=13981GH/s fixed rate=13500GH/s
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=631
Asic[ 0]:631
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631
Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:631
Asic[33]:631 Asic[34]:631 Asic[35]:631 Asic[36]:631 Asic[37]:631 Asic[38]:631 Asic[39]:631 Asic[40]:631
Asic[41]:631 Asic[42]:631 Asic[43]:631 Asic[44]:631 Asic[45]:631 Asic[46]:631 Asic[47]:631 Asic[48]:631
Asic[49]:631 Asic[50]:631 Asic[51]:631 Asic[52]:631 Asic[53]:631 Asic[54]:631 Asic[55]:631 Asic[56]:631
Asic[57]:631 Asic[58]:631 Asic[59]:631 Asic[60]:631 Asic[61]:631 Asic[62]:631
Chain:5 max freq=631
Chain:5 min freq=631
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=656
Asic[ 0]:656
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 Asic[16]:656
Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656 Asic[48]:656
Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656 Asic[56]:656
Asic[57]:656 Asic[58]:656 Asic[59]:656 Asic[60]:656 Asic[61]:656 Asic[62]:656
Chain:6 max freq=656
Chain:6 min freq=656
read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=662
Asic[ 0]:662
Asic[ 1]:662 Asic[ 2]:662 Asic[ 3]:662 Asic[ 4]:662 Asic[ 5]:662 Asic[ 6]:662 Asic[ 7]:662 Asic[ 8]:662
Asic[ 9]:662 Asic[10]:662 Asic[11]:662 Asic[12]:662 Asic[13]:662 Asic[14]:662 Asic[15]:662 Asic[16]:662
Asic[17]:662 Asic[18]:662 Asic[19]:662 Asic[20]:662 Asic[21]:662 Asic[22]:662 Asic[23]:662 Asic[24]:662
Asic[25]:662 Asic[26]:662 Asic[27]:662 Asic[28]:662 Asic[29]:662 Asic[30]:662 Asic[31]:662 Asic[32]:662
Asic[33]:662 Asic[34]:662 Asic[35]:662 Asic[36]:662 Asic[37]:662 Asic[38]:662 Asic[39]:662 Asic[40]:662
Asic[41]:662 Asic[42]:662 Asic[43]:662 Asic[44]:662 Asic[45]:662 Asic[46]:662 Asic[47]:662 Asic[48]:662
Asic[49]:662 Asic[50]:662 Asic[51]:662 Asic[52]:662 Asic[53]:662 Asic[54]:662 Asic[55]:662 Asic[56]:662
Asic[57]:662 Asic[58]:662 Asic[59]:662 Asic[60]:662 Asic[61]:662 Asic[62]:662
Chain:7 max freq=662
Chain:7 min freq=662
Miner fix freq ...
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=631
Asic[ 0]:631
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631
Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:631 Asic[31]:631 Asic[32]:631
Asic[33]:631 Asic[34]:631 Asic[35]:631 Asic[36]:631 Asic[37]:631 Asic[38]:631 Asic[39]:631 Asic[40]:631
Asic[41]:631 Asic[42]:631 Asic[43]:631 Asic[44]:631 Asic[45]:631 Asic[46]:631 Asic[47]:631 Asic[48]:631
Asic[49]:631 Asic[50]:631 Asic[51]:631 Asic[52]:631 Asic[53]:631 Asic[54]:631 Asic[55]:631 Asic[56]:631
Asic[57]:631 Asic[58]:631 Asic[59]:631 Asic[60]:631 Asic[61]:631 Asic[62]:631
Chain:5 max freq=631
Chain:5 min freq=631
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=656
Asic[ 0]:631
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 Asic[16]:631
Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 Asic[24]:631
Asic[25]:631 Asic[26]:631 Asic[27]:631 Asic[28]:631 Asic[29]:631 Asic[30]:637 Asic[31]:637 Asic[32]:637
Asic[33]:637 Asic[34]:637 Asic[35]:637 Asic[36]:637 Asic[37]:637 Asic[38]:637 Asic[39]:637 Asic[40]:637
Asic[41]:637 Asic[42]:637 Asic[43]:637 Asic[44]:637 Asic[45]:637 Asic[46]:637 Asic[47]:637 Asic[48]:637
Asic[49]:637 Asic[50]:637 Asic[51]:637 Asic[52]:637 Asic[53]:637 Asic[54]:637 Asic[55]:637 Asic[56]:637
Asic[57]:637 Asic[58]:637 Asic[59]:637 Asic[60]:637 Asic[61]:637 Asic[62]:637
Chain:6 max freq=637
Chain:6 min freq=631
read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=662
Asic[ 0]:631
Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 Asic[ 8]:631
Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:637 Asic[14]:637 Asic[15]:637 Asic[16]:637
Asic[17]:637 Asic[18]:637 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637 Asic[24]:637
Asic[25]:637 Asic[26]:637 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637 Asic[32]:637
Asic[33]:637 Asic[34]:637 Asic[35]:637 Asic[36]:637 Asic[37]:637 Asic[38]:637 Asic[39]:637 Asic[40]:637
Asic[41]:637 Asic[42]:637 Asic[43]:637 Asic[44]:637 Asic[45]:637 Asic[46]:637 Asic[47]:637 Asic[48]:637
Asic[49]:637 Asic[50]:637 Asic[51]:637 Asic[52]:637 Asic[53]:637 Asic[54]:637 Asic[55]:637 Asic[56]:637
Asic[57]:637 Asic[58]:637 Asic[59]:637 Asic[60]:637 Asic[61]:637 Asic[62]:637
Chain:7 max freq=637
Chain:7 min freq=631
max freq = 637
set baud=1
Chain[J6] PIC temp offset=62,0,0,0,0,0,35,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[5] chip[244] local:52 remote:55 offset:29
Chain[J6] chip[244] get middle temp offset=29 typeID=55
Chain[J7] PIC temp offset=62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:48 remote:51 offset:29
Chain[J7] chip[244] get middle temp offset=29 typeID=55
Chain[J8] PIC temp offset=62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:46 remote:49 offset:29
Chain[J8] chip[244] get middle temp offset=29 typeID=55
single board rate=4531 voltage limit=890 on chain[5]
get PIC voltage=890 on chain[5], check: must be < 890
single board rate=4551 voltage limit=890 on chain[6]
get PIC voltage=870 on chain[6], check: must be < 890
single board rate=4552 voltage limit=890 on chain[7]
get PIC voltage=870 on chain[7], check: must be < 890
Chain[J6] set working voltage=890 [91]
Chain[J7] set working voltage=870 [125]
Chain[J8] set working voltage=870 [125]
do heat board 8xPatten for 1 times
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
get send work num :57456 on Chain[5]
get send work num :57456 on Chain[6]
get send work num :57456 on Chain[7]
wait recv nonce on chain[5]
wait recv nonce on chain[6]
wait recv nonce on chain[7]
get nonces on chain[5]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=912 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
freq[00]=631 freq[01]=631 freq[02]=631 freq[03]=631 freq[04]=631 freq[05]=631 freq[06]=631 freq[07]=631
freq[08]=631 freq[09]=631 freq[10]=631 freq[11]=631 freq[12]=631 freq[13]=631 freq[14]=631 freq[15]=631
freq[16]=631 freq[17]=631 freq[18]=631 freq[19]=631 freq[20]=631 freq[21]=631 freq[22]=631 freq[23]=631
freq[24]=631 freq[25]=631 freq[26]=631 freq[27]=631 freq[28]=631 freq[29]=631 freq[30]=631 freq[31]=631
freq[32]=631 freq[33]=631 freq[34]=631 freq[35]=631 freq[36]=631 freq[37]=631 freq[38]=631 freq[39]=631
freq[40]=631 freq[41]=631 freq[42]=631 freq[43]=631 freq[44]=631 freq[45]=631 freq[46]=631 freq[47]=631
freq[48]=631 freq[49]=631 freq[50]=631 freq[51]=631 freq[52]=631 freq[53]=631 freq[54]=631 freq[55]=631
freq[56]=631 freq[57]=631 freq[58]=631 freq[59]=631 freq[60]=631 freq[61]=631 freq[62]=631
total valid nonce number:57456
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:25842
last_nonce_num:44022
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=912 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
freq[00]=631 freq[01]=631 freq[02]=631 freq[03]=631 freq[04]=631 freq[05]=631 freq[06]=631 freq[07]=631
freq[08]=631 freq[09]=631 freq[10]=631 freq[11]=631 freq[12]=631 freq[13]=631 freq[14]=631 freq[15]=631
freq[16]=631 freq[17]=631 freq[18]=631 freq[19]=631 freq[20]=631 freq[21]=631 freq[22]=631 freq[23]=631
freq[24]=631 freq[25]=631 freq[26]=631 freq[27]=631 freq[28]=631 freq[29]=631 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=637 freq[34]=637 freq[35]=637 freq[36]=637 freq[37]=637 freq[38]=637 freq[39]=637
freq[40]=637 freq[41]=637 freq[42]=637 freq[43]=637 freq[44]=637 freq[45]=637 freq[46]=637 freq[47]=637
freq[48]=637 freq[49]=637 freq[50]=637 freq[51]=637 freq[52]=637 freq[53]=637 freq[54]=637 freq[55]=637
freq[56]=637 freq[57]=637 freq[58]=637 freq[59]=637 freq[60]=637 freq[61]=637 freq[62]=637
total valid nonce number:57456
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:25977
last_nonce_num:36891
get nonces on chain[7]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=912 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
freq[00]=631 freq[01]=631 freq[02]=631 freq[03]=631 freq[04]=631 freq[05]=631 freq[06]=631 freq[07]=631
freq[08]=631 freq[09]=631 freq[10]=631 freq[11]=631 freq[12]=631 freq[13]=637 freq[14]=637 freq[15]=637
freq[16]=637 freq[17]=637 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=637 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=637 freq[34]=637 freq[35]=637 freq[36]=637 freq[37]=637 freq[38]=637 freq[39]=637
freq[40]=637 freq[41]=637 freq[42]=637 freq[43]=637 freq[44]=637 freq[45]=637 freq[46]=637 freq[47]=637
freq[48]=637 freq[49]=637 freq[50]=637 freq[51]=637 freq[52]=637 freq[53]=637 freq[54]=637 freq[55]=637
freq[56]=637 freq[57]=637 freq[58]=637 freq[59]=637 freq[60]=637 freq[61]=637 freq[62]=637
total valid nonce number:57456
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:26040
last_nonce_num:29777
chain[5]: All chip cores are opened OK!
Test Patten on chain[5]: OK!
chain[6]: All chip cores are opened OK!
Test Patten on chain[6]: OK!
chain[7]: All chip cores are opened OK!
Test Patten on chain[7]: OK!
setStartTimePoint total_tv_start_sys=323 total_tv_end_sys=324
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08
get RT hashrate from Chain[5]: (asic index start from 1-63)
Asic[01]=76.1850 Asic[02]=67.5110 Asic[03]=69.3400 Asic[04]=71.8060 Asic[05]=66.4370 Asic[06]=77.8790 Asic[07]=71.1680 Asic[08]=76.5710
Asic[09]=70.1790 Asic[10]=69.0380 Asic[11]=72.3930 Asic[12]=73.0980 Asic[13]=74.6750 Asic[14]=73.1150 Asic[15]=69.9100 Asic[16]=74.5240
Asic[17]=67.6120 Asic[18]=71.2020 Asic[19]=69.5580 Asic[20]=69.2730 Asic[21]=71.6550 Asic[22]=70.6990 Asic[23]=69.9600 Asic[24]=66.5380
Asic[25]=75.9670 Asic[26]=69.8930 Asic[27]=71.2360 Asic[28]=74.4900 Asic[29]=73.4840 Asic[30]=74.2390 Asic[31]=68.2160 Asic[32]=69.5080
Asic[33]=76.7050 Asic[34]=68.8030 Asic[35]=74.1380 Asic[36]=70.8830 Asic[37]=74.0710 Asic[38]=75.1780 Asic[39]=76.8220 Asic[40]=74.3390
Asic[41]=74.0540 Asic[42]=76.2020 Asic[43]=74.4060 Asic[44]=73.2660 Asic[45]=71.9070 Asic[46]=69.9440 Asic[47]=71.0680 Asic[48]=70.5480
Asic[49]=69.4570 Asic[50]=67.6450 Asic[51]=73.5170 Asic[52]=72.6620 Asic[53]=75.9500 Asic[54]=71.0510 Asic[55]=72.6620 Asic[56]=69.4910
Asic[57]=69.4740 Asic[58]=69.7260 Asic[59]=71.8560 Asic[60]=71.1010 Asic[61]=69.8770 Asic[62]=72.3600 Asic[63]=75.0270
get RT hashrate from Chain[6]: (asic index start from 1-63)
Asic[01]=67.2760 Asic[02]=74.4400 Asic[03]=73.0810 Asic[04]=74.5240 Asic[05]=71.5380 Asic[06]=67.3430 Asic[07]=74.8090 Asic[08]=73.0640
Asic[09]=68.7530 Asic[10]=73.3660 Asic[11]=74.0880 Asic[12]=75.7320 Asic[13]=69.2730 Asic[14]=73.7350 Asic[15]=70.0440 Asic[16]=73.4170
Asic[17]=70.2620 Asic[18]=69.3900 Asic[19]=70.7660 Asic[20]=73.4170 Asic[21]=71.1010 Asic[22]=67.1920 Asic[23]=73.5000 Asic[24]=69.5410
Asic[25]=66.7730 Asic[26]=68.4340 Asic[27]=69.7260 Asic[28]=66.1190 Asic[29]=67.7630 Asic[30]=77.6110 Asic[31]=71.7890 Asic[32]=74.7920
Asic[33]=76.4200 Asic[34]=72.3260 Asic[35]=69.9770 Asic[36]=65.9840 Asic[37]=73.5170 Asic[38]=76.0510 Asic[39]=75.0610 Asic[40]=66.0680
Asic[41]=76.4360 Asic[42]=69.9270 Asic[43]=73.6510 Asic[44]=71.5380 Asic[45]=71.4870 Asic[46]=73.8860 Asic[47]=75.4130 Asic[48]=75.5980
Asic[49]=69.9600 Asic[50]=66.9240 Asic[51]=70.1790 Asic[52]=71.2020 Asic[53]=73.0810 Asic[54]=71.2860 Asic[55]=69.9100 Asic[56]=73.0640
Asic[57]=72.5270 Asic[58]=72.7290 Asic[59]=71.3530 Asic[60]=73.8860 Asic[61]=74.7250 Asic[62]=76.1850 Asic[63]=77.4600
get RT hashrate from Chain[7]: (asic index start from 1-63)
Asic[01]=73.1150 Asic[02]=72.3930 Asic[03]=71.7720 Asic[04]=67.1080 Asic[05]=67.5950 Asic[06]=72.1080 Asic[07]=75.2960 Asic[08]=71.6720
Asic[09]=68.3670 Asic[10]=74.2550 Asic[11]=79.1040 Asic[12]=75.2960 Asic[13]=74.5740 Asic[14]=71.6550 Asic[15]=72.8970 Asic[16]=72.1080
Asic[17]=72.6280 Asic[18]=67.7290 Asic[19]=69.5080 Asic[20]=75.0440 Asic[21]=70.9170 Asic[22]=73.4330 Asic[23]=78.8860 Asic[24]=70.2960
Asic[25]=75.3460 Asic[26]=68.9870 Asic[27]=78.1310 Asic[28]=68.1990 Asic[29]=74.7760 Asic[30]=71.6050 Asic[31]=74.0210 Asic[32]=69.1050
Asic[33]=75.7820 Asic[34]=79.2720 Asic[35]=63.3000 Asic[36]=74.1550 Asic[37]=77.4260 Asic[38]=71.4200 Asic[39]=71.4200 Asic[40]=74.6250
Asic[41]=73.8190 Asic[42]=68.6520 Asic[43]=76.4870 Asic[44]=73.3830 Asic[45]=68.7360 Asic[46]=69.2220 Asic[47]=68.6690 Asic[48]=71.4700
Asic[49]=76.6710 Asic[50]=72.6110 Asic[51]=74.9430 Asic[52]=73.0810 Asic[53]=74.1210 Asic[54]=75.0100 Asic[55]=74.6410 Asic[56]=74.1210
Asic[57]=75.6980 Asic[58]=72.0580 Asic[59]=75.3630 Asic[60]=74.3900 Asic[61]=70.2790 Asic[62]=77.1080 Asic[63]=68.5510
Check Chain[J6] ASIC RT error: (asic index start from 1-63)
Check Chain[J7] ASIC RT error: (asic index start from 1-63)
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Done check_asic_reg
do read temp on Chain[5]
Chain[5] Chip[62] TempTypeID=55 middle offset=29
Chain[5] Chip[62] local Temp=73
Chain[5] Chip[62] middle Temp=82
Special fix Chain[5] Chip[62] middle Temp = 88
Done read temp on Chain[5]
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=55 middle offset=29
Chain[6] Chip[62] local Temp=70
Chain[6] Chip[62] middle Temp=79
Special fix Chain[6] Chip[62] middle Temp = 85
Done read temp on Chain[6]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=55 middle offset=29
Chain[7] Chip[62] local Temp=68
Chain[7] Chip[62] middle Temp=79
Special fix Chain[7] Chip[62] middle Temp = 83
Done read temp on Chain[7]
set FAN speed according to: temp_highest=73 temp_top1[PWM_T]=73 temp_top1[TEMP_POS_LOCAL]=73 temp_change=-1 fix_fan_steps=0
FAN PWM: 98
read_temp_func Done!
CRC error counter=0
|
|
|
|
|
