 Show Posts
|
|
Pages: [1]
|
Проблема решена. Все работает  U27 4VK4 вылетела (LN1134), кинули с U30 проводок с выхода и все заработало. Кидали проводок с U24, результата не было. Здравствуйте! Нашел на форуме свою проблему, а именно с Antminer S5 и проблема с хеш платой, которую описывали Вы и которую решили. U27 4VK4 вылетела (LN1134), кинули с U30 проводок с выхода и все заработало. Кидали проводок с U24, результата не было.Хотел попросить Вас помочь и мне. Могли бы Вы указать на примере платы как именно это выглядит. Спасибо!  |
|
|
|
Hi peeps... i have some question regarding the hashing boards. I've found the following, comparing with dogie's photoshoot:  In this image, i've seen that the new hashing boards come with additional pins, with a 3-bit address and a plug pin. Is this a sign of a coming device with 8 hashing boards? Can i connect 8 hashing boards to the same controller with different address bases? ... Hi! I saw your old messages about different data connectors of Antminers S5 hashig boards of old and new batches. Can you help me with connecting old hashing board to control board with data cables (16 & 18 Pin connectors)? Is it easy as I think? For example to connect '3v3' connector on hash board to equal connector on CtrlBoard? Thank you! you need a long cable, conect the board to the api board , and you will need a old s5 fimrware i think it is the first whit fan control.. But fan control is in last firmaware. Did you mean first firmware? Reboot miner to defult settings (small black button near ethernet cable) will help? |
|
|
|
By the way - the address lines tie directly into the temp sensors (LM75 I believe) so the controller can tell which board has which temperature. PLUG tells the controller a board is attached, but I forget if it pulls high or pulls low. Been a couple years since I needed to know that, but I've got notes on it at the shop. Everything else should go straight across.
Technically all you need to get hashing is 3V3, RST, RX, TX and GND. With PLUG tied to the appropriate rail.
Thank you! I will report my results here soon.  Hi! I connected hash board to control board with 18 pin connector, without 2 pins.  Board not hashing! I did not rebooted miner to defult settings or upgraded it to any firmware. Now it is working with last version of firmware.  |
|
|
|
By the way - the address lines tie directly into the temp sensors (LM75 I believe) so the controller can tell which board has which temperature. PLUG tells the controller a board is attached, but I forget if it pulls high or pulls low. Been a couple years since I needed to know that, but I've got notes on it at the shop. Everything else should go straight across.
I think I dont realy understand what it is about. Can you explain please. Is it mean, there will no correct information of temperature or information from PLUG to ctrl board will not be send at all, if I will not connect correctly? |
|
|
|
By the way - the address lines tie directly into the temp sensors (LM75 I believe) so the controller can tell which board has which temperature. PLUG tells the controller a board is attached, but I forget if it pulls high or pulls low. Been a couple years since I needed to know that, but I've got notes on it at the shop. Everything else should go straight across.
Technically all you need to get hashing is 3V3, RST, RX, TX and GND. With PLUG tied to the appropriate rail.
Thank you! I will report my results here soon. |
|
|
|
Hi peeps... i have some question regarding the hashing boards. I've found the following, comparing with dogie's photoshoot: In this image, i've seen that the new hashing boards come with additional pins, with a 3-bit address and a plug pin. Is this a sign of a coming device with 8 hashing boards? Can i connect 8 hashing boards to the same controller with different address bases? ... Hi! I saw your old messages about different data connectors of Antminers S5 hashig boards of old and new batches. Can you help me with connecting old hashing board to control board with data cables (16 & 18 Pin connectors)? Is it easy as I think? For example to connect '3v3' connector on hash board to equal connector on CtrlBoard? Thank you! |
|
|
|
Hello everyone! Have a problem with S3! 8 miners knocked out of mining. All eight are connected to the Internet (yellow LED lights, blinking green); at 6 6 have two diodes constant light (red and green) at the same time, one S3 has a blinking connection diodes ONLY, and one is blinking green LED (+ connection). Miners were overloaded (in the menu/OS adjust) then reinstalled on defult and then again regained their settings - nothing helped. Does not give any sign, only blinking ethernet connection. Here are screens - work schedule (I dont understand what they show, maybe someone can!) and the status of the miners. Can anyone tell what is the problem ?! http://www.fotolink.su/v.php?id=1f7b0763eb2de17bc75dc043815606cehttp://www.fotolink.su/v.php?id=9e5eb7b6c15282de30ca83fd12f1dfd5First thing would be to check if the PCI-e connectors all burned. Since they all stopped at the same time it *could* be possible you burned them all if you do not have proper surge protection. Secondly did you power cycle them, along with the router? I have an issue where when one S1 bug out, sometimes all the S1s, from different PSU, connectors etc everything all lose local connection. To fix i have to restart the router. Did you mean PCI-e connectors inside miner? The PCI-e sockets. In the S3 there are 2 per board and they're the thing you plug in your PCI-e female(tube) connector into. If you remove the shroud/cover it would be pretty obvious to notice if they have blackened. But you should be able to see just by looking at them with the PCI-e cables unconnected. Hi! There was problem with router. I rebooted it, then rebooted the miners, and everything all right! |
|
|
|
How did you power them? Looks to me that they have problem with psu(s).
Hi! There was problem with router. I rebooted it, then rebooted the miners, and everything all right! |
|
|
|
Hello everyone! Have a problem with S3! 8 miners knocked out of mining. All eight are connected to the Internet (yellow LED lights, blinking green); at 6 6 have two diodes constant light (red and green) at the same time, one S3 has a blinking connection diodes ONLY, and one is blinking green LED (+ connection). Miners were overloaded (in the menu/OS adjust) then reinstalled on defult and then again regained their settings - nothing helped. Does not give any sign, only blinking ethernet connection. Here are screens - work schedule (I dont understand what they show, maybe someone can!) and the status of the miners. Can anyone tell what is the problem ?! http://www.fotolink.su/v.php?id=1f7b0763eb2de17bc75dc043815606cehttp://www.fotolink.su/v.php?id=9e5eb7b6c15282de30ca83fd12f1dfd5First thing would be to check if the PCI-e connectors all burned. Since they all stopped at the same time it *could* be possible you burned them all if you do not have proper surge protection. Secondly did you power cycle them, along with the router? I have an issue where when one S1 bug out, sometimes all the S1s, from different PSU, connectors etc everything all lose local connection. To fix i have to restart the router. Did you mean PCI-e connectors inside miner? |
|
|
|
How did you power them? Looks to me that they have problem with psu(s).
PSUs are okay. I want to change the firmware. Can't find the data of old firmware. |
|
|
|
Hello everyone! Have a problem with S3! 8 miners knocked out of mining. All eight are connected to the Internet (yellow LED lights, blinking green); at 6 6 have two diodes constant light (red and green) at the same time, one S3 has a blinking connection diodes ONLY, and one is blinking green LED (+ connection). Miners were overloaded (in the menu/OS adjust) then reinstalled on defult and then again regained their settings - nothing helped. Does not give any sign, only blinking ethernet connection. Here are screens - work schedule (I dont understand what they show, maybe someone can!) and the status of the miners. Can anyone tell what is the problem ?! http://www.fotolink.su/v.php?id=1f7b0763eb2de17bc75dc043815606cehttp://www.fotolink.su/v.php?id=9e5eb7b6c15282de30ca83fd12f1dfd5 |
|
|
|
|
The same problem with withdraw! There is no Virtex in all lists of exchanges any more - this is scary!
|
|
|
|
I'm the editor of BitcoinWarrior.net. I haven't gotten any emails about this, but found this thread and will be following up. Thanks. So check this problem and investigate it wider! |
|
|
|
|
Dear forum members, please help, where Crypto-Trade trading platform codes (CT redeem code) can be cashed to USD? Thank U!
|
|
|
|
Hi everyone! I am sick and tired from that BA!!!  26/11/13 I made an order X-1 but when they have stated to postpone the delivery device in May I immediately canceled the order and demanded a refund! After long declinations me to agree on their wacky proposals that lasted six weeks, finally on April 25th, I was blessed with a news: "Dear Roman, We have removed your order from shipping queue and placed it on refunds queue." (from my ticket [#JTR-408-33380]: refund) But... still nothing!!! Already formed about 4 ticket reminded me - as if they had disappeared!!! FU(KING ALIENS Who knows, how to make a criminal case on these animals? |
|
|
|
|
