Hi
Nice one thanks! v009 has some kind of voltage regulator.
I did not think of this possibility at all. I will purchase one and will try for sure. I bought v006 as they are simple and was hoping less things to go wrong with this load and temperatures.
Thanks again.

Last update I think!
Reinstall of windows 10 version 1803, AMD drivers 17.1.14. Problematic card was reflashed first with original bios than again with modded one.
Same behavior. Tried to remove one of other working cards and the issue is the same. It appears much rare but still appears.
I saw on GPUz during this low hashrate the VDDC power draw drops as well. I am not sure why but this is related to low hashrate.
So I am pretty exhausted with ideas and all point to card problem. But until it gets fully broken I cannot claim for warranty situation.
Many thanks to all of you and if someone think of something else even orthodox just let me know and I will test.

Cheers!

Hi guys!
When I configured the card 1175/2050 it was fluctuating again but now with settings 1130/2050@ 0.9V it is OK again for 2 days now.
But now 2 cards are showing much more fan speed than other two. I have set target temp to 65 degrees. Before in order to maintain this value fans were at 44-46% in similar room temp as current one but now it is around 60%. Just for this 2 cards. They were cleaned regularly and are far apart.
So I am pretty sure that it is a time to re-flash the cards. This is the only obvious reason for such odd behavior. The concerning thing is that the fan issue is affecting 2 cards. One of them is the one with fluctuations.

I was trying to avoid windows reinstalation but now I will have to do it together with cards reflash.
I think if I will not do it the odd issues will continue so in order to not full this article I will do a clean install of everything and BIOS reflash. Than will share the results.

To answer @abhiseshakana:
No memory errors. There are several showing here and there but for months. To summup for around 30 days I have total 4-5 errors for all 4 cards. So I think this is considered as normal.

Hi markiz73
How you would explain that this card was working absolutely fine for about 5 months and showed some mood just now. That puzzle me. Because if the problem was with voltage or speed it would have showed this problem at very beginning as I initially tested all cards and installed them in the RIG.
I am trying to explain myself is there something that could wear out. If it was a fan it would be expected but for well managed and appropriate cooled card I cannot explain.
But now I am trying with 1175/2050@0.912V in order to reduce heat a bit and crossing fingers to continue working fine next few days. If yes will try to increase memory clock.
Still looking for opinions though! Every brainstorming will help me and hopefully someone else in the future.

Just side note: Very thankful to you all and entire community.
Cheers!

Hi
A little update. Changed speed to 1200/2050@0.912V and so far 2 days with no fluctuations. Which is a bit odd to me as I tried before with stock settings 1360/2000 and the problem still exists. But now with this ones it seems OK.
I am wondering could it be something with drivers. Somehow this particular card to be mapped to the certain driver parts somewhere in the OS and no matter I move it to assign same drivers to this physical card. I know this is a wild guess but just wondering.
In this case pure reinstall would do the job but as I mentioned I have image of C: drive and revert back if something goes wrong in order to eliminate OS as a problem. And with this particular OS it was working almost 6 months without any issues. No updates installed since then.

Haven not tried to remove one card but this will be the next step. Will update in a few days again.
@Geraldo: clarify please what you mean by "re-mode the card"? To flash the BIOS again with "Turbo" memory timings or just tweaking the voltages and Mhz with different values?

Cheers!

Hi and thanks for your feedback.

Temperatures are almost the same around 64-65 CPU, 73-74 VRMs. Fan speeds are around 45% when it is cold in the room and around 60-63% when it was much hotter. That was ~2 months ago. Now the weather here is fine as outside temperatures, respectively inside as well.
When the inconsistent hash rate is happening no change to any parameter, manual or from the card itself. I mean clocks, voltages or etc. Monitoring them with HWinfo and GPU-z. Fan speed is auto corrected from the card of course but in above mentioned range. I have not seen fan speed more than 66% in very hot day.

Now I gave the cards 2 steps higher voltage to 0.9V but same behavior. And as I stated above I tried with stock cpu/mem clocks, voltages and hash rate was jumping occasionally minus 2-3-5Mhs down but in his case not from 30.1 but from 28.1.

I will try with 1200/2050 just for confining your suggestions. The strange thing is that if I restart the rig the hashrate is consistent for several hours no matter clock/voltage. So I will need some days in order to prove the behavior with new settings.

Many thanks once again!

Hello everyone!
Need your advice please on following problem I have with one if my rigs.
The rig is with 4xRX580 8Gb cards ASUS. 3x OC version and one STRIX (with 3 fans).
The problem is that it was running 6 months without any problems at all. But since last month or so one of the cards (OC one) started to drop hash rate randomly. It is mining 30.1Mh/s and all of a sudden drops to ~28Mh/s, in next second is OK again. In a minute drops to ~26Mhs and next second again to 30.1 as usual. And so on until I restart the rig.
In the beginning started to do it rare but now it is very often. When I restart the rig it is mining without any problem for several hours and starts do this again.

First thing came to my mind I did reimage of Windows. I have made an IMAGE of C partition in the moment I tested the rig and it was stable 5 months ago. So the image is pretty fine and well tested. Nothing changed to card behavior. Did a clean install of drives - same thing. Last version of drivers and claymore - same thing. Changed the card to different riser and different power rails (for riser and 8pin). Same card have same behavior no matter the riser. So I isolated risers and cables as issue. Isolated drivers and claymore version. Windows installation as well. almost forgot. Tried with stock overclocking settings - same thing.

So please for advice, can I do something else or the card is on its way for refurbishment.

mining ether in ethermine pool.
windows 10 (1709)
4G RAM, 30G virtual memory
850W corsair gold power supply.
Problematic card settings: 1150/2120@0.85V. fans ~50% and temp 64/73 for CPU/VRMs.
Using overdriveN tool for tuning and memory tweaked with Polaris editor with proposed setting for hynix memory.
As I told earlier since last month this card was running very fine with same settings since january. Nothing changed to any settings.

Sorry for long post and all advices are much appreciated!