aah nice.

So I've set this a9 to

    "T1performance": true,
    "T1Pll1": "1300",
    "T1Pll2": "1300",
    "T1Pll3": "1300",
    "T1VID1": "170",
    "T1VID1": "170",
    "T1VID1": "170",
    "A1Fanspd": "20",
    "A1Fanmode": "0"


...

   u'09 pllOptimal': False,
   u'10 Cooldown': 0,
   u'10 Fail count': 0,
   u'10 Fail reset': 0,
   u'10 HW errors': 3,
   u'10 Nonce ranges': 0,
   u'10 Nonces found': 36,
   u'10 PLL': 354,
   u'10 Stales': 0,
   u'10 Temp': 524,
   u'10 nVol': 862,
   u'10 pllOptimal': False,
   u'11 Cooldown': 0,
   u'11 Fail count': 0,
   u'11 Fail reset': 0,
   u'11 HW errors': 4,
   u'11 Nonce ranges': 0,
   u'11 Nonces found': 33,
   u'11 PLL': 354,
   u'11 Stales': 0,
   u'11 Temp': 526,
   u'11 nVol': 872,
   u'11 pllOptimal': False,
   u'Calls': 0,
   u'Chain ID': 2,
   u'Chain num': 2,
   u'Chain skew': 0,
   u'Disabled': False,
   u'Elapsed': 3468,
   u'Enabled chips': u'fff',
   u'Fan duty': 20,
   u'ID': u'HLT2',
   u'MHS av': 16500.0,
   u'Max': 0.0,
   u'Min': 99999999.0,
   u'Num active chips': 12,
   u'Num chips': 12,
   u'Num cores': 381,
   u'PLL': 354,
   u'STATS': 2,
   u'Temp': 54.0,
   u'Temp max': 58.0,
   u'Temp min': 51.0,
   u'VidOptimal': True,
   u'Voltage Avg': 860.0,
   u'Voltage Max': 872.0,
   u'Voltage Min': 850.0,
   u'VoltageBalanced': False,
   u'Wait': 0.0,
   u'iVid': 166,
   u'pllOptimal': True},

Here basilp,


{
    "pools": [
        {
            "url": "stratum+tcp://equihash.usa.nicehash.com:3357",
            "user": "36Rzs1zaAPphdPzaiUpGTYty64SNDaCNyu",
            "pass": "x"
        }
    ],
    "api-listen": true,
    "api-port": "4028",
    "api-allow": "W:0/0,W:127.0.0.1"
    "noauto": true,
    "T1Pll1": "1250",
    "T1Pll2": "1250",
    "T1Pll3": "1250",
    "T1VID1": "166",
    "T1VID2": "166",
    "T1VID3": "166",
    "A1Fanspd": "50",
    "A1Fanmode": "0
}

I am running in performance mode and using Bitmain PSU.


I am mining ZEC. Not sure about the payout since I have 160 kSol pointed to the same address. NH is good also but you get what others are willing to pay minus NH fees.

Hard to tell really. I haven't seen any noticable improvement in hash rates though... I am curious about the voltages for the first one it says a default of 8.


--T1VID1 <arg>      set voltage (1 ~ 255) (default:
--T1VID1 <arg>      set voltage (1 ~ 255) (default: 166)
--T1VID2 <arg>      set voltage (1 ~ 255) (default: 166)

Although it's hard to know how specific to the device those voltages. I can't see 166 set as voltage anywhere in my miner logs. Where are others seeing it?

Also not really sure why I'm seeing 20W lower power draw.

who wants to be brave and attempt some commands? 

Looks like there operators are responsible for performance tuning:

--T1efficient       Tune Dragonmint T1 per chain voltage and frequency for optimal efficiency
--T1factory         Tune Dragonmint T1 per chain voltage and frequency by factory autotune strategy
--noauto            Disable Dragonmint T1 per chain auto voltage and frequency tuning
--T1performance     Tune Dragonmint T1 per chain voltage and frequency for maximum performance
--T1Pll1 <arg>      Set PLL Clock in bitmine A1 broad 1 chip (-1: 1000MHz, >0:Look PLL table) (default: 1250)
--T1Pll2 <arg>      Set PLL Clock in bitmine A1 broad 2 chip (-1: 1000MHz, >0:Look PLL table) (default: 1250)
--T1Pll3 <arg>      Set PLL Clock in bitmine A1 broad 3 chip (-1: 1000MHz, >0:Look PLL table) (default: 1250)
--T1Pll4 <arg>      Set PLL Clock in bitmine A1 broad 4 chip (-1: 1000MHz, >0:Look PLL table) (default: 1250)
--T1Pll5 <arg>      Set PLL Clock in bitmine A1 broad 5 chip (-1: 1000MHz, >0:Look PLL table) (default: 1250)
--T1Pll6 <arg>      Set PLL Clock in bitmine A1 broad 6 chip (-1: 1000MHz, >0:Look PLL table) (default: 1250)
--T1Pll7 <arg>      Set PLL Clock in bitmine A1 broad 7 chip (-1: 1000MHz, >0:Look PLL table) (default: 1250)
--T1Pll8 <arg>      Set PLL Clock in bitmine A1 broad 8 chip (-1: 1000MHz, >0:Look PLL table) (default: 1250)
--T1VID1 <arg>      set voltage (1 ~ 255) (default:
--T1VID1 <arg>      set voltage (1 ~ 255) (default: 166)
--T1VID2 <arg>      set voltage (1 ~ 255) (default: 166)
--T1VID3 <arg>      set voltage (1 ~ 255) (default: 166)
--T1VID4 <arg>      set voltage (1 ~ 255) (default: 166)
--T1VID5 <arg>      set voltage (1 ~ 255) (default: 166)
--T1VID6 <arg>      set voltage (1 ~ 255) (default: 166)
--T1VID7 <arg>      set voltage (1 ~ 255) (default: 166)
--T1VID8 <arg>      set voltage (1 ~ 255) (default: 166)
--A1Fanspd <arg>    set fan speed (0 ~ 100) (default: -1)
--A1Fanmode <arg>   set fan control (0 ~ 1) (default: 1)


config located in /config/ folder

part of config file:
    "api-listen": true,
    "api-port": "4028",
    "api-allow": "R:0/0,W:127.0.0.1",
    "T1performance": true,