 Show Posts
|
|
Pages: [1]
|
|
serms my s15 will not use fixed mode with your firmwire.
flashed it with sd and all. the firmwire got loaded but fixed mode doesent seems to work.
is there anyway to change "low temp enviroment"?
i dont have ida pro version. is there any other software that work with elf to arm?
newbie here
|
|
|
|
Anyone gotten to Overclock these babies? got an S15 28th firmwire 3dec 2018 seems i cannot do anything with it. Ssh doesent work neather, thats why im wondering if anyone gotten to OC these ones or gotten any more info out of them  |
|
|
|
just curious have you been working any on the voltage control? |
|
|
|
This is a very good question. First on the CRC error -- that is going to happen some and is only a problem if it is constant. It happens on even the stock firmwares depending on machines, temps, frequencies, and phase of the moon.
Temperatures will play into how far you can push these, but there is not a clear formula for that. What's really interesting is I have a customer with a large install (1000+ machines) who has observed that there is a point where the machines get too cold and slow down! I'm unsure of the exact details on the temperatures, just the observation that was shared with me.
So yes, temperature has a play both when going up and when going down.
The summers here are very hot -- my miners I had to constantly tune even through the day to get maximum out of them; they always ran best at night.
I hope this helps some.
Jason
I Reflashed the firmware and now i can push it higher then 656mhz. Temps now is 49-50c fans 2000 rpm Okey. well if it starts to drop When there is to cold outside i have to split the intake air abit Thanks for that info. Another question.. I also tried the Biggie firmware earlier, with the same Mhz it could spike to +17ksols avg was the around 14.5 i think i got higher spikes with the "biggie" firmware then the mini. Avg is better at the mini FW though Good job! will buy the license when you start bringing in new ones |
|
|
|
|
Thoughts.
z9 mini
I have my miners Hosted outside, OR direct outside air, we have been having around -15c and the miner worked great got it up to stable at 681mhz since release.
2 fans front 1800rpm rear 1640 rpm Chips temp around 28-30c hash Avg 14.9ksols
Today the weather Drastically changed to +2c and i got all 3 boards xxxx
seems that it was the bm1740_verify_nonce_integrality CRC error. Reebooted but only took like 7min then got the same error again.
But after that ive only been able to maintain 656mhz.
soon as i go above that i loose one board.
CAN it be possible that the colder the chips can be maintained the higher mhz we can maintain? I never tried above 681mhz
|
|
|
|
|
With this fw is it possible to get above 657mhz and nit to loose one board?
You got the batch 4 to 737?
Regards
|
|
|
|
Cool the odd thing is the firmware on it is the same as the firmware currently on bitmain. It only has balanced for freq options. The batch 1 fw runs fine with only 1 board reporting temp. I ran your z9 2.0d and stock z9 firmware on this mini it runs fine but same thing no temps on any board but it clocks up to 737 stable your fw also unlocked the 4th port on the controller so I could run an extra hashboard where the stock mini only allows 3.
Wait...what??! Ur running Z9 FW on your Z9 mini and it works fine?  Dev fee version has always worked, the issue has been the temp controls and such which is why I have not been recommending it Jason Sorry for asking, ive been using your 2.0D on my mini batch2. Automatic fan doesent work, but i can manually set it and it works Using push/pull with 2 fans. Temp reading seems to work on 1 board i still got numbers on the other boards but only like 15 and 7c. But my hashrate is fluctuating alot. With batch 1 firmwire its between 14.0-14.4 Average 14.3ksols at 662MHZ Highest i can go. With your FW its between 12-18k Average 14.7ksols at 681MHZ Its kinda like 2board jumps up to 6-8 ksols and one board goes down to 2-5ksols. next its the other 2 board that jumps up and another one goes down. are you aware of this? and sorry again for asking about the mini when your priority are on payed biggies and great job btw!  |
|
|
|
|
Try lowering mhz. Almost the same happened to me in batch 2.
Try lower to 650 an go up from that.
|
|
|
|
Hi great job with the firmware! Ive managed to change the bmminer to 8.8v 9v and changing back to original. Its an 13.5th with 1600w bitmain psu At first it worked great with the 8.8v 725mhz. Temperature around 93-97c. Then it just stopped hashing after a few hours and playing around with the miner. It works for 3-4 min then it stops to hash. In the log ut says to high temperature. And then all of a sudden i starts to get "lost connection" i have other miners on the same Network and they still work. Does anyone see anything strange in the log? Thanks for all the help. and keep up the work with the coding! [ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-gb190cb0-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 27800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 258048
[ 0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map e6fd8000
[ 0.000000] Normal zone: 1520 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 194560 pages, LIFO batch:31
[ 0.000000] HighMem zone: 496 pages used for memmap
[ 0.000000] HighMem zone: 63488 pages, LIFO batch:15
[ 0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 256528
[ 0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 884148K/1032192K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 148044K reserved, 253952K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06d1374 (6949 kB)
[ 0.000000] .init : 0xc06d2000 - 0xc0705380 ( 205 kB)
[ 0.000000] .data : 0xc0706000 - 0xc074cf78 ( 284 kB)
[ 0.000000] .bss : 0xc074cf84 - 0xc078d9fc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to f0004000
[ 0.000000] zynq_clock_init: clkc starts at f0004100
[ 0.000000] Zynq clock init
[ 0.000014] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000301] ps7-ttc #0 at f0006000, irq=43
[ 0.000606] Console: colour dummy device 80x30
[ 0.000642] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[ 0.040203] pid_max: default: 32768 minimum: 301
[ 0.040426] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.040448] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.042596] CPU: Testing write buffer coherency: ok
[ 0.042947] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.043007] Setting up static identity map for 0x4c4af8 - 0x4c4b50
[ 0.043229] L310 cache controller enabled
[ 0.043248] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.121033] CPU1: Booted secondary processor
[ 0.210224] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.210356] Brought up 2 CPUs
[ 0.210375] SMP: Total of 2 processors activated.
[ 0.210383] CPU: All CPU(s) started in SVC mode.
[ 0.211047] devtmpfs: initialized
[ 0.213450] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.214655] regulator-dummy: no parameters
[ 0.221906] NET: Registered protocol family 16
[ 0.224156] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.226426] cpuidle: using governor ladder
[ 0.226440] cpuidle: using governor menu
[ 0.233803] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.235311] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.235325] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.235437] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[ 0.257093] bio: create slab <bio-0> at 0
[ 0.258501] vgaarb: loaded
[ 0.259196] SCSI subsystem initialized
[ 0.260062] usbcore: registered new interface driver usbfs
[ 0.260374] usbcore: registered new interface driver hub
[ 0.260611] usbcore: registered new device driver usb
[ 0.261145] media: Linux media interface: v0.10
[ 0.261308] Linux video capture interface: v2.00
[ 0.261550] pps_core: LinuxPPS API ver. 1 registered
[ 0.261562] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.261689] PTP clock support registered
[ 0.262042] EDAC MC: Ver: 3.0.0
[ 0.263113] Advanced Linux Sound Architecture Driver Initialized.
[ 0.265953] DMA-API: preallocated 4096 debug entries
[ 0.265967] DMA-API: debugging enabled by kernel config
[ 0.266046] Switched to clocksource arm_global_timer
[ 0.287228] NET: Registered protocol family 2
[ 0.287885] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.287979] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.288138] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.288206] TCP: reno registered
[ 0.288225] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.288275] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.288543] NET: Registered protocol family 1
[ 0.288904] RPC: Registered named UNIX socket transport module.
[ 0.288916] RPC: Registered udp transport module.
[ 0.288925] RPC: Registered tcp transport module.
[ 0.288933] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.288946] PCI: CLS 0 bytes, default 64
[ 0.289384] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.291401] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.292792] bounce pool size: 64 pages
[ 0.293681] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.293877] msgmni has been set to 1486
[ 0.294642] io scheduler noop registered
[ 0.294656] io scheduler deadline registered
[ 0.294702] io scheduler cfq registered (default)
[ 0.303544] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.303565] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.427215] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 0.999677] console [ttyPS0] enabled
[ 1.003954] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[ 1.011571] [drm] Initialized drm 1.1.0 20060810
[ 1.028558] brd: module loaded
[ 1.037936] loop: module loaded
[ 1.047684] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.053436] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.061279] libphy: XEMACPS mii bus: probed
[ 1.065650] ------------- phy_id = 0x3625e62
[ 1.070554] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.079157] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.085783] ehci-pci: EHCI PCI platform driver
[ 1.093065] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.099925] usbcore: registered new interface driver usb-storage
[ 1.106883] mousedev: PS/2 mouse device common for all mice
[ 1.112978] i2c /dev entries driver
[ 1.119863] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.125341] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.131262] Xilinx Zynq CpuIdle Driver started
[ 1.136127] sdhci: Secure Digital Host Controller Interface driver
[ 1.142224] sdhci: Copyright(c) Pierre Ossman
[ 1.146605] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.153364] mmc0: no vqmmc regulator found
[ 1.157403] mmc0: no vmmc regulator found
[ 1.196072] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.204757] usbcore: registered new interface driver usbhid
[ 1.210264] usbhid: USB HID core driver
[ 1.214962] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.221263] nand: Micron MT29F2G08ABAEAWP
[ 1.225225] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.231164] Bad block table found at page 131008, version 0x01
[ 1.237384] Bad block table found at page 130944, version 0x01
[ 1.243438] 3 ofpart partitions found on MTD device pl353-nand
[ 1.249227] Creating 3 MTD partitions on "pl353-nand":
[ 1.254316] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.262376] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.269701] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.278667] TCP: cubic registered
[ 1.281907] NET: Registered protocol family 17
[ 1.286620] Registering SWP/SWPB emulation handler
[ 1.292502] regulator-dummy: disabling
[ 1.296859] UBI: attaching mtd1 to ubi0
[ 1.823005] UBI: scanning is finished
[ 1.834524] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.841601] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.848364] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.855028] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.861905] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 1.867886] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.874994] UBI: max/mean erase counter: 16356/13952, WL threshold: 4096, image sequence number: 1984962504
[ 1.884730] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[ 1.893947] UBI: background thread "ubi_bgt0d" started, PID 1080
[ 1.893952] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.897921] ALSA device list:
[ 1.897925] No soundcards found.
[ 1.914321] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[ 1.943481] UBIFS: recovery needed
[ 2.000112] UBIFS: recovery completed
[ 2.003780] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 2.009723] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 2.018864] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 2.028721] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 2.033747] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 56FDF5FA-8D29-4AA7-95D4-1C2E28C7C4E9, small LPT model
[ 2.045511] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 2.052932] devtmpfs: mounted
[ 2.056035] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[ 2.900198] random: dd urandom read with 0 bits of entropy available
[ 3.296070]
[ 3.296070] bcm54xx_config_init
[ 3.906090]
[ 3.906090] bcm54xx_config_init
[ 6.906924] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 6.913016] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 30.436845] In axi fpga driver!
[ 30.439918] request_mem_region OK!
[ 30.443305] AXI fpga dev virtual address is 0xf01fe000
[ 30.448451] *base_vir_addr = 0x8c510
[ 30.463183] In fpga mem driver!
[ 30.466591] request_mem_region OK!
[ 30.470100] fpga mem virtual address is 0xf3000000
[ 31.235980]
[ 31.235980] bcm54xx_config_init
[ 31.865896]
[ 31.865896] bcm54xx_config_init
[ 34.866450] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 34.872468] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 186.015364] random: nonblocking pool is initialized
[ 311.934609] UBI: scrubbed PEB 859 (LEB 0:2), data moved to PEB 883
[ 324.178183] UBI: scrubbed PEB 406 (LEB 0:1), data moved to PEB 795
[ 328.313711] UBI: scrubbed PEB 27 (LEB 0:1), data moved to PEB 468
[ 367.822069] UBI: scrubbed PEB 44 (LEB 0:1), data moved to PEB 805
[ 379.897076] UBI: scrubbed PEB 812 (LEB 0:1), data moved to PEB 883
[ 1017.466462] UBI: scrubbed PEB 872 (LEB 0:2), data moved to PEB 884
[ 1107.746481] UBI: scrubbed PEB 1 (LEB 0:2), data moved to PEB 901
[ 1156.072693] UBI: scrubbed PEB 551 (LEB 0:1), data moved to PEB 869
Detect 1GB control board of XILINX
Miner Type = S9
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
Fix freq=550 Chain[5] voltage_pic=6 value=940
Fix freq=550 Chain[6] voltage_pic=6 value=940
Fix freq=550 Chain[7] voltage_pic=6 value=940
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has no freq in PIC, set default freq=550M
Chain[J6] has no core num in PIC
Chain[J7] has no freq in PIC, set default freq=550M
Chain[J7] has no core num in PIC
Chain[J8] has no freq in PIC, set default freq=550M
Chain[J8] has no core num in PIC
Miner fix freq ...
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550 Asic[62]:550
Chain:5 max freq=550
Chain:5 min freq=550
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550 Asic[62]:550
Chain:6 max freq=550
Chain:6 min freq=550
read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550 Asic[62]:550
Chain:7 max freq=550
Chain:7 min freq=550
max freq = 550
set baud=2
Chain[J6] PIC temp offset=62,0,0,0,0,0,35,28
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[5] chip[244] local:27 remote:30 offset:27
Chain[J6] chip[244] get middle temp offset=27 typeID=55
Chain[J6] chip[136] use PIC middle temp offset=28 typeID=00
Warning: Chain[J6] has no temp offset in PIC! will fix it
New offset Chain[5] chip[244] local:27 remote:30 offset:27
Chain[J6] chip[244] get middle temp offset=27 typeID=55
Chain[J7] PIC temp offset=62,0,0,0,0,0,35,28
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:27 remote:32 offset:25
Chain[J7] chip[244] get middle temp offset=25 typeID=55
Chain[J7] chip[136] use PIC middle temp offset=28 typeID=00
Warning: Chain[J7] has no temp offset in PIC! will fix it
New offset Chain[6] chip[244] local:27 remote:32 offset:25
Chain[J7] chip[244] get middle temp offset=25 typeID=55
Chain[J8] PIC temp offset=62,0,0,0,0,0,35,28
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:28 remote:32 offset:26
Chain[J8] chip[244] get middle temp offset=26 typeID=55
Chain[J8] chip[136] use PIC middle temp offset=28 typeID=00
Warning: Chain[J8] has no temp offset in PIC! will fix it
New offset Chain[7] chip[244] local:28 remote:32 offset:26
Chain[J8] chip[244] get middle temp offset=26 typeID=55
Chain[J6] set working voltage=940 [6]
Chain[J7] set working voltage=940 [6]
Chain[J8] set working voltage=940 [6]
setStartTimePoint total_tv_start_sys=80 total_tv_end_sys=81
restartNum = 2 , auto-reinit enabled...
Fatal Error: Temperature is too high!
Fatal Error: Temperature is too high!
Fatal Error: Temperature is too high!
Fatal Error: Temperature is too high!
Fatal Error: Temperature is too high!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
Fatal Error: network connection lost!
Fatal Error: Temperature is too high!
do read_temp_func once...
do check_asic_reg 0x08
get RT hashrate from Chain[5]: (asic index start from 1-63)
get RT hashrate from Chain[6]: (asic index start from 1-63)
get RT hashrate from Chain[7]: (asic index start from 1-63)
Check Chain[J6] ASIC RT error: (asic index start from 1-63)
Check Chain[J7] ASIC RT error: (asic index start from 1-63)
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Done check_asic_reg
do read temp on Chain[5]
Chain[5] Chip[62] TempTypeID=55 middle offset=27
read failed, old value: Chain[5] Chip[62] local Temp=91
read failed on Chain[5] Chip[62] middle Temp old value:97
Done read temp on Chain[5]
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=55 middle offset=25
read failed, old value: Chain[6] Chip[62] local Temp=89
read failed on Chain[6] Chip[62] middle Temp old value:92
Done read temp on Chain[6]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=55 middle offset=26
read failed, old value: Chain[7] Chip[62] local Temp=89
read failed on Chain[7] Chip[62] middle Temp old value:92
Done read temp on Chain[7]
set FAN speed according to: temp_highest=97 temp_top1[PWM_T]=97 temp_top1[TEMP_POS_LOCAL]=91 temp_change=17 fix_fan_steps=0
set full FAN speed...
FAN PWM: 100
read_temp_func Done!
CRC error counter=0 |
|
|
|
|
