Show Posts
|
Pages: [1]
|
Mine also have the 4 pin regulator, they seem to work fine, if you don't forget to cool them ... One of mine dropped all the components because I tought it would run on stock frequency without extra cooling. I re-soldered them all by hand using flux, and it's up and running again, with printed 40x40 air ducts and fans connected on them, now they behave and don't drop parts Whatever you do, use the Kano version of cgminer, it runs more stable then the other versions found on github and is running with about 0.5A less power usage for the same frequency settings ...
|
|
|
no more stock on bitshopper.de ? There is still stock left on eyeboot ...
|
|
|
Ik heb nog een zeusminer hurricane X3 liggen, moest je interesse hebben (en gratis stroom)
|
|
|
Hoeveel ben je bereid er voor neer te tellen ? Ik heb nog een witte liggen van 16GB, heb me een 64GB met 4G gekocht omdat ik te vaak remote internet nodig had en ik niet altijd wilde tetheren met mijn iphone
|
|
|
cannachris heeft zijn bod herbevestigd; voorlopig voorbehouden voor cannachris
|
|
|
price-change, aangezien cannachris niet meer reageerd op mail/sms/forum messages zie op
|
|
|
Beste forum leden
ik verkoop 2x antminer S1 + corsair RM850 voeding
De miners zijn niet overclocked geweest en draaien stabiel. De 2 miners hebben pci-e aansluitingen. Levering in de originele dozen. Ophalen in Belgie / Limburg vraagprijs :1.65 Btc voor de 2 miners incl voeding en verzending naar Belgie / Nederland of doe een aanvaardbaar bod
Escrow mogelijk via PsychoticBoy als dit gewenst is
|
|
|
On my devices the vendor id is the same, so the plugdev file should be universal. Did you have success on frequencies above 850 MHz? I noticed you put a voltage section in the configuration, that sets some voltage on gpio5 Is this documented somewhere else ? I looked in the datasheet but couldn't find anything there, neither in the gridseed cgminer version on github. Where did you find this additional information ? For now it's running stable on my pi @850MHz for 3 hours and my pi is clocked at default frequency.
|
|
|
Ok, some standard questions to be sure we have the same config: Do you have your pi running at stock frequency ? Did you add additional parameters to your modules configuration ? What is your cmdline.txt
Mine has crashed twice with spurious interrupt errors, killing the miner and taking down the pi alltogether. I'm running with these options : baud=115200,freq=850,chips=5,modules=1,btc=0 The pi is on a powered usb hub, I've been using these hubs for my pi's for ages and not seen any issues. The miner is on a dedicated 12V powersupply, that allows 5A, so don't see an issue there neither. Any suggestions are welcome.
|
|
|
Any chance of a Pi image with compiled binary? Here's a compiled binary built on raspbian: https://db.tt/UygLkqwdThanks heaps - is the MHz set as compile time? Anyway to get 850mhz? --gridseed-options=baud=115200,freq=850 still no work utility d'oh forgot the --scrypt Also this seems to work OK for 10 miners but over that kernel panics the Pi.
EDIT: Nope crashes with 10 also, tried with two different sets of 10 miners Also seems that no work is getting submitted and work utility is zeroI pushed a change and updated the binary to add nonce generation per chip. This gives some assurance that you don't have any completely busted chips. I built your code from github, it is working fine on my pi. The Accepted shares are off for some reason on the interface. I also monitor the cgminer with the networking API and there they seem to be correct. Not sure where this might be hidden in the code , but if I have time later, I might take a look at it.
|
|
|
makkelijkst gaat zijn om de sporen (printbanen) verderop een beetje proper te krabben en dan met wire-wrap (zo een heel dunne draad) de contacten terug te verbinden met de printbanen. Ik zie dat er een stuk van de printbaan mee af gekomen is. Je moet eerst de socket terug goed vast zetten en daarna de rest van de verbindingen een voor een terug leggen. Moest dat niet lukken, soldeer je gewoon rechtstreeks je kabel aan de antminer. Alleen zien dat je de juiste pinnen gebruikt, micro-usb is 5pins op pcb, normaal is er 1pin niet aangesloten, dat zie je duidelijk op de pcb. de 2 pinnen ernaast zijn D+ en D- en dan heb je nog GND en +5V er naast aan beide kanten.
|
|
|
van waar ben je? Dit is redelijk snel en simpel te repareren met een goede soldeerbout.
|
|
|
if t..s - 5 who bought 5 cards can acknowledge he got a refund for his investment, trust can be upped again ...
|
|
|
Hi,
I'm interested in 1 device, shipment to Belgium
|
|
|
Hello I want to reserve 3 cards with shipment to Belgium
Thanks for this groupbuy
|
|
|
|