Show Posts
|
Pages: [1] 2 3 4 5 »
|
i have a wallet on the binance smart chain that has been compromised. im looking for a bot/script that can automatically send the rewards/claims of a "certain token" from that wallet to a different address faster than a human can
If you are a newbie please do not respond.
|
|
|
Finally figured it out !!!
On some miners you need to plug in a dummy DVI plug or a monitor cable to one of the video cards. Dont ask me why because i have a ton of miners that do need this. Once i did this and disabled the onboard video card the miner started working.
|
|
|
Guys,
I have one miner that i cannot figure out. Mind you i have 30+ but yes i cannot figure this one out, and its driving me nuts.
The issue is that after the Windows 10 April update the miner will start but pauses....it does not close. I have tried everything i know and nothing. So i went ahead and installed a clean version of 1709 build with all of its updates.
I have reinstalled 11.7(which was working with no issues prior) and still nothing. I have tried adrenaline 18.2 and even downgraded to the blockchain drivers and still nothing. The motherboard is up to date, windows sees all the cards...no issues there. I have patched the drivers...etc...etc...
These are AMD RX560's that have been modded...and again these were working fine before the darn update got me.....I have also excluded the claymore folder in defender, set a pause for 30 seconds etc...
Im hoping someone out there has run into this prior....i am now having this same issue with another rig running rx470's
Any help would be appreciated
Thanks
|
|
|
Guys,
I have one miner that i cannot figure out. Mind you i have 30+ but yes i cannot figure this one out, and its driving me nuts.
The issue is that after the Windows 10 April update the miner will start but pauses....it does not close. I have tried everything i know and nothing. So i went ahead and installed a clean version of 1709 build with all of its updates.
I have reinstalled 11.7(which was working with no issues prior) and still nothing. I have tried adrenaline 18.2 and even downgraded to the blockchain drivers and still nothing. The motherboard is up to date, windows sees all the cards...no issues there. I have patched the drivers...etc...etc...
These are AMD RX560's that have been modded...and again these were working fine before the darn update got me.....I have also excluded the claymore folder in defender, set a pause for 30 seconds etc...
Im hoping someone out there has run into this prior....
Any help would be appreciated
Thanks
have you tried running 1 GPU on PCIex16 slot? dont use riser I have a feeling that one of your hardware might caused your issue i havent but i will give it a try..whats strange is that they were all working before the windows update....thanks
|
|
|
Guys,
I have one miner that i cannot figure out. Mind you i have 30+ but yes i cannot figure this one out, and its driving me nuts.
The issue is that after the Windows 10 April update the miner will start but pauses....it does not close. I have tried everything i know and nothing. So i went ahead and installed a clean version of 1709 build with all of its updates.
I have reinstalled 11.7(which was working with no issues prior) and still nothing. I have tried adrenaline 18.2 and even downgraded to the blockchain drivers and still nothing. The motherboard is up to date, windows sees all the cards...no issues there. I have patched the drivers...etc...etc...
These are AMD RX560's that have been modded...and again these were working fine before the darn update got me.....I have also excluded the claymore folder in defender, set a pause for 30 seconds etc...
Im hoping someone out there has run into this prior....
Any help would be appreciated
Thanks
|
|
|
Has anyone been able to figure out how to use the new "Y" feature in 11.6 to automatically turn on compute mode....
I have tried the following but a no go
Make a batch file in an editor and nameit.bat then create a shortcut to it. Nameit.bat - shortcut. then right click on Nameit.bat - shortcut ->Properties->Shortcut tab -> Advanced and click Run as administrator. Execute it from the shortcut.
Any help would be appreciated
|
|
|
notbatman im having a hell of a time with some xfx rx570's 4gb and was wondering if you can take a look at the bios. Most of the ones i have have elpida. Using Polaris editor 1.6.6 im getting some to do 29mh while others can only do 27mh stable. I have tried copying different straps, anoraks bios etc. I have also tried different drivers from the august blockchain to the newest adrenaline and getting the same results. Below is the original bios http://s000.tinyupload.com/index.php?file_id=74853664151030133515thanks in advance for any help
|
|
|
Guys
I have a strange issue with one of my rigs that i cannot figure out. I currently have 13 rigs but for some reason this one has been an issue for me
8 sapphire 570's modded 1500+ straps using PBE 1.6.3 asus z270-a 8gb ddr 4
2 EVGA G3 850's and 2 server PSU's
Im using claymore 10 and have used 10.1 ..using the latest amd drivers with compute turned on.
Windows 10 1703 build just like all my other rigs
the issue is that whenever i change any voltage settings in claymore and i reboot the computer the miner locks up the computer after it initializes the open cl...
once it locks up reboot it again and the hashrate is back at stock...reboot again and then starts working ok
another issue is that every minute or so i get a random card that drops the hashrate...2-3 hashes
ive tried lowering the clocks and slowly raising them but no luck
is this a Claymore issue ?
I have changed out the mobo, the DDR, the pci risers...currently i have 3200 watts available to it so i know its not a power issue....
Any help would be appreciated
|
|
|
Guys
I have a strange issue with one of my rigs that i cannot figure out. I currently have 13 rigs but for some reason this one has been an issue for me
8 sapphire 570's modded 1500+ straps using PBE 1.6.3 asus z270-a 8gb ddr 4
2 EVGA G3 850's and 2 server PSU's
Im using claymore 10 and have used 10.1 ..using the latest amd drivers with compute turned on.
Windows 10 1703 build just like all my other rigs
the issue is that whenever i change any voltage settings in claymore and i reboot the computer the miner locks up the computer after it initializes the open cl...
once it locks up reboot it again and the hashrate is back at stock...reboot again and then starts working ok
another issue is that every minute or so i get a random card that drops the hashrate...2-3 hashes
ive tried lowering the clocks and slowly raising them but no luck
I have changed out the mobo, the DDR, the pci risers...currently i have 3200 watts available to it so i know its not a power issue....
Any help would be appreciated
|
|
|
Can anyone help with figuring out how to solo mine ?
I need the rpc port and a way to download the chain....
does pirl use a version of geth ?
Thanks in advance
|
|
|
all the exchanges say exp is worth around 2.00 USD but this pool states its worth 4.65 ? on the home page...im confused also what is up with whattomine....with EXP its way off ?
|
|
|
Guys,
I have one card on one of my rigs that will not switch from graphics to compute on the latest drivers...i have rebooted countless times...nothing
Anyone else have this issue ?
Thanks in advance
|
|
|
Guys
im using claymore with my rigs...as always im trying how to maximize hash rate but keep electricity costs down
Im using the claymore commands -mvddc and -cvddc
i have used those in conjunction with the -powlim -xxx but i do not see any difference when i add the -pow lim option
anyone have any thoughts they could share regarding which one would do the best job ?
...also read somewhere that the gpu and mem voltage is paired...meaning one cannot say lower the gpu voltage and not the mem ?
Thanks in advance
|
|
|
Sent info and an email 2 days ago...please respond
|
|
|
Guys,
Struggling with this card. Currently getting 27 with about 1150 watts at the wall with 8 cards.
Anyone getting better results ? Maybe this is all its got
Thanks
|
|
|
hello, I have 5 exact messages from contact form, I guess it works ;-) Already have answered to your email.
ok sent info...lets see
|
|
|
Guys,
not sure where to post this...
I am trying to use hashcat to "try" and recover my wallet. I have recovered the hash already with john the ripper.
My question is if anyone knows...the hash pertains to the passphrase of the wallet or does it pertain to the seed/keys ?
Using bitcoin core
Any help would be appreciated
|
|
|
|