Show Posts
|
Pages: [1] 2 »
|
100% of all the fees collected will be distributed to tokens holders right? So how will you guys earn money?
It's a exchange , they will charge something , I mean its impossible like them to give you same value with 1 ETH ( actually 340 $ ).
|
|
|
I don't like your turnover and profit estimates like they are made for phishing. It's impossible to make it in next 2-3 years for a new project. 115M monthly?!?! profit??
How you will solve the documentation problem on CCs deposits? The only option is like localbitcoins.com and then why we need you? Do you see localbitcoins to make even 1% of your profit estimates and they are proven project??
Why you are avoiding answer my questions and only answering some shill newbies saying how good you are? 115M monthly profit lol bro , they have lowest fees than others exchanges , and also you do not need to be verified with ID or other documents , if you go on kraken or other trading site you will need to be first time verified if you want to exchange crypto to USD
|
|
|
What are the differences from other ICOs???
|
|
|
on the advice set yakminer. I use here are the settings for the 280X
{code and stuff}
speed - 285 h\s
but one card does not work, and constantly driver error, or the card falls or Sikc and Dead
that's not right I can not understand ...
I think your "starttime" is wrong. Try making it 1388361600, Also make sure you have "gpu-threads" : "1”. And then, cut it down to a bare minimum to test. Get rid of Expiry, Queue, Scan-time, anything other than temp control which is really not vital. If you get it working that way, you can slowly ad them back in. Good luck!
|
|
|
I've actually been able to push my memclocks to 1500, but that was in the scrypt days. Usually there's not enough difference in hash power for the heat generated, especially with asic resistance coin formulas. As it is, both my cards hover between 69 and 71 with the settings I posted (with help from some extra case fans).
I did partially figure the issue out tho and am now mining away. I pulled this out of the config:
--gpu-powertune 20 --queue 0 --expiry 1 --scan-time 1 --no-submit-stale
So something in there really didn't work well with NF16. I'll do some experimenting later on as I fine tune.
|
|
|
I'm getting one accept after a few minutes of mining and then I'm getting dropped by the pool (or at least it's showing no workers, even tho my cards are chugging away) with no further accepted shares. Running 2x 280x, about 275h/s. Nothing else has changed aside from the slight configuration updates fro N16. Any ideas?
can you share a batch for 280x ? Here's what I am using: yacminer.exe --scrypt-chacha --nfmin 4 --nfmax 30 --starttime 1388361600 -d 0,1 -R 1280 --buffer-size 2590 -g 1 -w 128 --lookup-gap 8 --gpu-engine 1200,1200 --gpu-memclock 1200,1200 --gpu-powertune 20 --queue 0 --expiry 1 --scan-time 1 --no-submit-stale --temp-cutoff 90 --temp-overheat 85 --auto-fan
|
|
|
I'm getting one accept after a few minutes of mining and then I'm getting dropped by the pool (or at least it's showing no workers, even tho my cards are chugging away) with no further accepted shares. Running 2x 280x, about 275h/s. Nothing else has changed aside from the slight configuration updates fro N16. Any ideas?
|
|
|
Is MineBig really not finding any Aiden blocks, or is it just not updating?
|
|
|
N Factor changes tomorrow, correct? Maybe in some time zones this has happened already?
|
|
|
Right now I can spend $6750 for 1000 DRK to setup a masternode. Earnings per day would be: 1.019 DRK = $6.912
I can also spend $6750 for 5870 XC. Earnings per day from POS would be: 0.54 XC = $0.616
Yes but you are forgetting about the fact that you will also get money from it being a node. Will I earn more if I setup 100 XC wallets/nodes then? Is there a limit to the number of nodes I can have? More on this please. Someone smart speculate what running an Xnode would bring in daily coinwise.
|
|
|
Is there more info to dirtydiggers? What are the "low fees"? How often are we paid, as blocks are found?
Thanks!
|
|
|
Sorry guys for feeding the troll. I think we have all seen his true intentions now. For something more worthy of discussion, how about we celebrate the fact that after yesterday's announcements, we now have arguably the most competent team in crypto. Read up on the team here: http://xc-official.com/the-xc-team/Not just 1, not just 2, not just 3, but ELEVEN Competent and Motivated Official Team Members. This is worthy of being excited about.
|
|
|
Bigger logo (lunch is late being delivered):
|
|
|
Filthy, you asked for this yesterday on page 668 Let me know if you want anything tweaked.
|
|
|
Yeah, I would tip him 0.25 XCurrency for it if he had a adress in his Sig. cryptoboh wants u to submit it to his twitter.. possible u can win some xc Go ahead and submit. If you need it smaller or cropped, just let me know (I can supply the PSD as well if needed). My XC address: XDp8cyLKByuJdUnrmB8phaypSVu2v3LCaU
|
|
|
I've been looking, but I probably don't know the correct terms. Is there a way to convert the current UTC Net Hashrate and Difficulty to "scrypt" numbers?
|
|
|
I've been mining on cryptotrain for a while now and every now and then I switch to direct UTC pool mining, just to compare numbers which have always been pretty close (need to mine on cryptotrain for 3+ days to get full results).
But now since I updated to AMD 14.4 drivers (which do increase speed and lower temps for X11 at least) I get nothing but hardware errors from my old configs. I had used the config generator to set me up and everything was working correctly. Now I get tons of HW errors. Any experiencing the same or have working 280x settings they can share once on 14.4?
Thanks!
|
|
|
Voted!
Anyone else having an issue with "adn.minebig.com". I haven't been able to connect since yesterday, but my hashes are being accepted.
|
|
|
|