 Show Posts
|
|
Pages: [1]
|
|
little question : i have a t17 with a hashboard with 3 defectives ASIC, 27 still ok but the original firmware turn off completly the hashboar. is you firmware can use the 27 asics and disable the 3 defectives one to continue working anyway?
|
|
|
|
|
i have a question : is it possible to activate only the asicboost but not the overclock ?
asicboost must offer 10-15% increase with same stability.. or am i wrong ?
|
|
|
|
|
i expected a lot with this new version with auto-tuing...and finally what a big deception...
impossible to get over 45/48 Ths with a T17, after, its overheating...the air is 7°, so very cold to the machine, but its not enough.
this firmware seems useless for overclocking with air cooling.
|
|
|
|
|
belgium, shipping worldwide possible
|
|
|
|
|
200$ for S9
150$ for M3X
Cleaned, revised, perfect condition & working fully ( no defective chips, news fans, can show hashrate last month )
|
|
|
|
|
i have latest T17 firmware and it work fine nicehash. i tried overclock firmware, and in that case nicehash didn't reconized it
you have to do it by SD, bec it overide the downgrade protection.
|
|
|
|
|
for 10 x 2500w miner ( T17, S9 , M3X, etc..), one extractor 50cm is enough ( extract 6900 m³/h ).
|
|
|
|
error: get_temp_info: read temp sensor failed
its bad sign, its mean motherboard or hash board are defective, captor dont give temperature... |
|
|
|
You can downgrade it with signed firmware but it looks like Bitmain always remove older version from their download page.
Maybe some user here who use the same miner has a backup or older firmware version but I don't recommend to download them from unknown source unless if they have a bitmain direct link of older version.
if you use a non signed firmware ( like AsicTuner overclock ), it wont work on NiceHash ( maybe not compatible with their "Asicboost" ? ). But if you use original firmware, even the latest, it works perfectly. To downgare, just recover 1st firmware ( not on their website, they removed it ), put on SD and flash it through the Sd reader. |
|
|
|
The dev fee does not affect hashrate.
really ? so how did you get your dev free ? |
|
|
|
|
I hope the auto tune will fix the problem...because actually its nearly impossible to go over 49 TH/S in the very best case without overheating ( 45 TH/S for most of machines )
Another problem, the dev fee....
I have 1 T17 producing 49.48Th/s on miner control panel but on slushpool i have only 44.80Th/s ... its 10% of dev fee...
another exemple :
46.15Th/s on miner control panel and...41.64Th/s on slushpool... so less than original firmware !
I checked other machine with original firmware, and the the value are both same in miner config panel and on slushpool.
|
|
|
|
i used this firmware : 20191205119-sig_4803Kernel Version Linux 4.6.0-xilinx-gff8137b-dirty #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
File System Version Thu Dec 5 11:19:08 CST 2019I can't unclock SSH anymore since i reloaded the original firmware. I have thisi error with your tool : SSH Unlock
Asic.to
[+] Found Antminer T17.. Try unlock it..
/www/pages/cgi-bin/create_log_backup.cgi: exit: line 27: Illegal number: -1
[+] Connect: 192.168.0.17 Success..
I think the new firmware from bitmain fix the exploit of create_log_backup.cgi. |
|
|
|
|
Hi Taserz,
I think i did a mistake : i unlocked T17 with your tool, flashed your firmware, but it doesn't start to mine.
So, i reflashed with the original firmware. With original firmware it mines correctly. I i wanted to try again your firmware.
but there is a problem : i think the firmware i downloaded on bitmain fix the the exploit you used in your tool, i can't access SSH anymore.
There is a way to downgrade it ?
|
|
|
|
|
