 Show Posts
|
|
Pages: [1] 2 »
|
Here's the latest with just one hashboard connected. I have also successfully flashed with the SD card. Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 197340K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 32036K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 18996K (cc873000 - cdb00000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
nand_read_bbt: bad block at 0x000002420000
nand_read_bbt: bad block at 0x000002440000
nand_read_bbt: bad block at 0x000002460000
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 17/7, WL threshold: 4096, image sequence number: 131776731
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID AD63E5E5-DA5C-4DAD-9550-959A80DA7C1B, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 3652/898, WL threshold: 4096, image sequence number: 267841159
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 31AA9D87-7438-4BA5-AB48-E0CFF57D9D53, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab01b
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
[2021-04-15 15:44:27.190] start listen on 6060 ...
2021-04-15 15:43:57 driver-btm-soc.c:7273:init_freq_mode: This is scan-user version
2021-04-15 15:43:57 driver-btm-soc.c:8125:bitmain_soc_init: T15
2021-04-15 15:43:57 driver-btm-soc.c:8126:bitmain_soc_init: opt_multi_version=1
2021-04-15 15:43:57 driver-btm-soc.c:8127:bitmain_soc_init: opt_bitmain_ab=1
2021-04-15 15:43:57 driver-btm-soc.c:8128:bitmain_soc_init: opt_bitmain_economic_mode=false
2021-04-15 15:43:57 driver-btm-soc.c:8129:bitmain_soc_init: opt_bitmain_work_mode_test = 0
2021-04-15 15:43:57 driver-btm-soc.c:7682:_show_sn: no SN got, please write SN to /nvdata/sn
2021-04-15 15:43:57 driver-btm-soc.c:7304:init_phy_mem_nonce2_jobid_address: Detect 256MB control board of XILINX
2021-04-15 15:43:57 driver-btm-soc.c:8149:bitmain_soc_init: Miner compile time: Fri Dec 13 15:46:16 CST 2019 type: Antminer T15
2021-04-15 15:43:57 driver-btm-soc.c:8151:bitmain_soc_init: last commit version: 53156cb commit time: 2019-11-06 10:21:42 build: 2019-12-13 15:53:57
2021-04-15 15:43:57 driver-btm-soc.c:7336:check_fan_multi: check fan for 20 times...
2021-04-15 15:43:59 driver-btm-soc.c:8214:bitmain_soc_init: miner ID : 8074f42429e04814
2021-04-15 15:43:59 driver-btm-soc.c:7410:init_miner_version: FPGA Version = 0xB01B
2021-04-15 15:43:59 driver-btm-soc.c:1092:check_chain: get_hash_on_plug is 0x1
2021-04-15 15:43:59 driver-btm-soc.c:1104:check_chain: !! chain[0]is exist
2021-04-15 15:44:01 eeprom.c:1418:eeprom_load: done
2021-04-15 15:44:01 driver-btm-soc.c:7431:init_pcb_version: chain[0] PCB Version : 0x0101
2021-04-15 15:44:01 driver-btm-soc.c:7449:init_pcb_version: chain[0] BOM Version : 0x0100
2021-04-15 15:44:02 dspic33ep16gs202.c:538:reset_pic: chain[0] ok
2021-04-15 15:44:06 dspic33ep16gs202.c:504:jump_to_app_from_loader: chain[0] ok
2021-04-15 15:44:06 power.c:137:power_init: power init ...
2021-04-15 15:44:06 driver-btm-soc.c:3130:heart_beat_func_one_chain: for chain 0
2021-04-15 15:44:06 power.c:114:power_on: init gpio907
2021-04-15 15:44:08 dspic33ep16gs202.c:409:hashboard_power_cntl: [0] ok, i2c=0!
2021-04-15 15:44:11 driver-btm-soc.c:8241:bitmain_soc_init: Enter 30s sleep to make sure power release finish.
2021-04-15 15:44:41 driver-btm-soc.c:7626:set_working_voltage_by_eeprom: eeprom voltage[0] = 19.300000
2021-04-15 15:44:41 driver-btm-soc.c:7630:set_working_voltage_by_eeprom: max = 19.30, min = 19.30
2021-04-15 15:44:41 power.c:149:set_working_voltage: working_voltage = 19.300000
2021-04-15 15:44:41 power.c:274:set_iic_power_to_highest_voltage: setting to voltage: 20.00 ...
2021-04-15 15:44:41 power.c:227:set_iic_power_by_voltage: now setting voltage to : 20.000000
2021-04-15 15:44:41 eeprom.c:840:travel_eeprom_store: chain[0] data in eeprom is:
magic number: 0x7f
freq data per ASIC:
IC[000]:450 IC[001]:450 IC[002]:450 IC[003]:450 IC[004]:420
IC[005]:420 IC[006]:450 IC[007]:450 IC[008]:450 IC[009]:450
IC[010]:420 IC[011]:450 IC[012]:450 IC[013]:450 IC[014]:450
IC[015]:450 IC[016]:450 IC[017]:420 IC[018]:450 IC[019]:450
IC[020]:450 IC[021]:420 IC[022]:450 IC[023]:450 IC[024]:450
IC[025]:450 IC[026]:420 IC[027]:450 IC[028]:450 IC[029]:450
IC[030]:450 IC[031]:450 IC[032]:450 IC[033]:450 IC[034]:420
IC[035]:420 IC[036]:450 IC[037]:450 IC[038]:450 IC[039]:450
IC[040]:420 IC[041]:450 IC[042]:450 IC[043]:450 IC[044]:450
IC[045]:450 IC[046]:450 IC[047]:420 IC[048]:450 IC[049]:450
IC[050]:450 IC[051]:450 IC[052]:420 IC[053]:450 IC[054]:450
IC[055]:450 IC[056]:450 IC[057]:450 IC[058]:450 IC[059]:420
voltage: 18.60 V
hash rate: 06797 GH/s
freq data per ASIC in mode2:
IC[000]:510 IC[001]:510 IC[002]:510 IC[003]:510 IC[004]:480
IC[005]:480 IC[006]:510 IC[007]:510 IC[008]:510 IC[009]:510
IC[010]:480 IC[011]:510 IC[012]:510 IC[013]:510 IC[014]:510
IC[015]:510 IC[016]:510 IC[017]:480 IC[018]:510 IC[019]:510
IC[020]:510 IC[021]:480 IC[022]:510 IC[023]:510 IC[024]:510
IC[025]:510 IC[026]:480 IC[027]:510 IC[028]:510 IC[029]:510
IC[030]:510 IC[031]:510 IC[032]:510 IC[033]:480 IC[034]:510
IC[035]:480 IC[036]:510 IC[037]:510 IC[038]:510 IC[039]:510
IC[040]:480 IC[041]:510 IC[042]:510 IC[043]:510 IC[044]:510
IC[045]:510 IC[046]:510 IC[047]:510 IC[048]:480 IC[049]:510
IC[050]:510 IC[051]:510 IC[052]:480 IC[053]:510 IC[054]:510
IC[055]:510 IC[056]:510 IC[057]:510 IC[058]:510 IC[059]:480
voltage in mode2: 19.30 V
hash rate in mode2: 07703 GH/s
2021-04-15 15:44:42 dspic33ep16gs202.c:409:hashboard_power_cntl: [1] ok, i2c=0!
2021-04-15 15:44:42 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-04-15 15:44:45 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-04-15 15:44:48 driver-btm-soc.c:5456:check_asic_num_by_pre_open_core: Try to find asic by pre core: times 0
2021-04-15 15:44:48 driver-btm-soc.c:5412:check_asic_num_without_power_off: Open 16 core for chain 0
2021-04-15 15:44:48 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 16
2021-04-15 15:44:49 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:44:49 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 16
2021-04-15 15:44:50 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:44:50 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 16
2021-04-15 15:44:50 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:44:50 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 16
2021-04-15 15:44:51 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:44:51 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-04-15 15:44:54 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-04-15 15:44:58 driver-btm-soc.c:5426:check_asic_num_without_power_off: chain 0, find asic num = 0
2021-04-15 15:44:58 driver-btm-soc.c:5412:check_asic_num_without_power_off: Open 32 core for chain 0
2021-04-15 15:44:58 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 32
2021-04-15 15:45:00 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:45:00 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 32
2021-04-15 15:45:01 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:45:01 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 32
2021-04-15 15:45:03 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:45:03 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 32
2021-04-15 15:45:04 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:45:04 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-04-15 15:45:07 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-04-15 15:45:11 driver-btm-soc.c:5426:check_asic_num_without_power_off: chain 0, find asic num = 0
2021-04-15 15:45:11 driver-btm-soc.c:5412:check_asic_num_without_power_off: Open 64 core for chain 0
2021-04-15 15:45:11 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 64
2021-04-15 15:45:14 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:45:14 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 64
2021-04-15 15:45:17 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:45:17 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 64
2021-04-15 15:45:20 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:45:20 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 64
2021-04-15 15:45:23 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:45:23 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-04-15 15:45:26 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-04-15 15:45:30 driver-btm-soc.c:5426:check_asic_num_without_power_off: chain 0, find asic num = 0
2021-04-15 15:45:30 driver-btm-soc.c:5466:check_asic_num_by_pre_open_core: Unable to find all asic [0] times, power off hash board and wait [30] sec
2021-04-15 15:45:31 dspic33ep16gs202.c:409:hashboard_power_cntl: [0] ok, i2c=0!
2021-04-15 15:46:01 power.c:274:set_iic_power_to_highest_voltage: setting to voltage: 20.00 ...
2021-04-15 15:46:01 power.c:227:set_iic_power_by_voltage: now setting voltage to : 20.000000
2021-04-15 15:46:02 dspic33ep16gs202.c:409:hashboard_power_cntl: [1] ok, i2c=0!
2021-04-15 15:46:04 driver-btm-soc.c:5456:check_asic_num_by_pre_open_core: Try to find asic by pre core: times 1
2021-04-15 15:46:04 driver-btm-soc.c:5412:check_asic_num_without_power_off: Open 16 core for chain 0
2021-04-15 15:46:04 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 16
2021-04-15 15:46:05 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:46:05 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 16
2021-04-15 15:46:05 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:46:05 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 16
2021-04-15 15:46:06 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:46:06 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 16
2021-04-15 15:46:07 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:46:07 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-04-15 15:46:10 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-04-15 15:46:14 driver-btm-soc.c:5426:check_asic_num_without_power_off: chain 0, find asic num = 0
2021-04-15 15:46:14 driver-btm-soc.c:5412:check_asic_num_without_power_off: Open 32 core for chain 0
2021-04-15 15:46:14 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 32
2021-04-15 15:46:16 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:46:16 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 32
2021-04-15 15:46:17 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:46:17 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 32
2021-04-15 15:46:19 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:46:19 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 32
2021-04-15 15:46:20 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:46:20 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-04-15 15:46:23 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-04-15 15:46:27 driver-btm-soc.c:5426:check_asic_num_without_power_off: chain 0, find asic num = 0
2021-04-15 15:46:27 driver-btm-soc.c:5412:check_asic_num_without_power_off: Open 64 core for chain 0
2021-04-15 15:46:27 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 64
2021-04-15 15:46:30 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:46:30 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 64
2021-04-15 15:46:33 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:46:33 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 64
2021-04-15 15:46:36 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:46:36 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 64
2021-04-15 15:46:39 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-15 15:46:39 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-04-15 15:46:42 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-04-15 15:46:46 driver-btm-soc.c:5426:check_asic_num_without_power_off: chain 0, find asic num = 0
2021-04-15 15:46:46 driver-btm-soc.c:5466:check_asic_num_by_pre_open_core: Unable to find all asic [1] times, power off hash board and wait [30] sec
2021-04-15 15:46:47 dspic33ep16gs202.c:409:hashboard_power_cntl: [0] ok, i2c=0! |
|
|
|
I've reflashed the software and have disconnected one of the hash boards. Here's what I get now: Miner Type Antminer T15 Hostname antMiner Model GNU/Linux Hardware Version Socket connect failed: Connection refused Kernel Version Linux 4.6.0-xilinx-gff8137b-dirty #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018 File System Version Fri Dec 13 15:46:16 CST 2019 CGminer Version Uptime 7 Load Average 0.09, 0.16, 0.08 The pool is set up correctly, as I have an S17 using the same details with a different address. The miner status table is just empty. Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 197340K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 32036K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 18996K (cc873000 - cdb00000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
nand_read_bbt: bad block at 0x000002420000
nand_read_bbt: bad block at 0x000002440000
nand_read_bbt: bad block at 0x000002460000
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 17/7, WL threshold: 4096, image sequence number: 131776731
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID AD63E5E5-DA5C-4DAD-9550-959A80DA7C1B, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 3652/898, WL threshold: 4096, image sequence number: 267841159
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 31AA9D87-7438-4BA5-AB48-E0CFF57D9D53, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab01b
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
[2021-04-14 12:23:15.376] start listen on 6060 ...
2021-04-14 12:22:45 driver-btm-soc.c:7273:init_freq_mode: This is scan-user version
2021-04-14 12:22:45 driver-btm-soc.c:8125:bitmain_soc_init: T15
2021-04-14 12:22:45 driver-btm-soc.c:8126:bitmain_soc_init: opt_multi_version=1
2021-04-14 12:22:45 driver-btm-soc.c:8127:bitmain_soc_init: opt_bitmain_ab=1
2021-04-14 12:22:45 driver-btm-soc.c:8128:bitmain_soc_init: opt_bitmain_economic_mode=false
2021-04-14 12:22:45 driver-btm-soc.c:8129:bitmain_soc_init: opt_bitmain_work_mode_test = 0
2021-04-14 12:22:45 driver-btm-soc.c:7682:_show_sn: no SN got, please write SN to /nvdata/sn
2021-04-14 12:22:45 driver-btm-soc.c:7304:init_phy_mem_nonce2_jobid_address: Detect 256MB control board of XILINX
2021-04-14 12:22:45 driver-btm-soc.c:8149:bitmain_soc_init: Miner compile time: Fri Dec 13 15:46:16 CST 2019 type: Antminer T15
2021-04-14 12:22:45 driver-btm-soc.c:8151:bitmain_soc_init: last commit version: 53156cb commit time: 2019-11-06 10:21:42 build: 2019-12-13 15:53:57
2021-04-14 12:22:45 driver-btm-soc.c:7336:check_fan_multi: check fan for 20 times...
2021-04-14 12:22:47 driver-btm-soc.c:8214:bitmain_soc_init: miner ID : 8074f42429e04814
2021-04-14 12:22:47 driver-btm-soc.c:7410:init_miner_version: FPGA Version = 0xB01B
2021-04-14 12:22:47 driver-btm-soc.c:1092:check_chain: get_hash_on_plug is 0x5
2021-04-14 12:22:47 driver-btm-soc.c:1104:check_chain: !! chain[0]is exist
2021-04-14 12:22:47 driver-btm-soc.c:1104:check_chain: !! chain[2]is exist
2021-04-14 12:22:52 eeprom.c:1418:eeprom_load: done
2021-04-14 12:22:52 driver-btm-soc.c:7431:init_pcb_version: chain[0] PCB Version : 0x0101
2021-04-14 12:22:52 driver-btm-soc.c:7449:init_pcb_version: chain[0] BOM Version : 0x0100
2021-04-14 12:22:52 driver-btm-soc.c:7431:init_pcb_version: chain[2] PCB Version : 0x0101
2021-04-14 12:22:52 driver-btm-soc.c:7449:init_pcb_version: chain[2] BOM Version : 0x0100
2021-04-14 12:22:53 dspic33ep16gs202.c:538:reset_pic: chain[0] ok
2021-04-14 12:22:57 dspic33ep16gs202.c:504:jump_to_app_from_loader: chain[0] ok
2021-04-14 12:22:58 dspic33ep16gs202.c:538:reset_pic: chain[2] ok
2021-04-14 12:23:02 dspic33ep16gs202.c:504:jump_to_app_from_loader: chain[2] ok
2021-04-14 12:23:02 power.c:137:power_init: power init ...
2021-04-14 12:23:02 driver-btm-soc.c:3130:heart_beat_func_one_chain: for chain 2
2021-04-14 12:23:02 driver-btm-soc.c:3130:heart_beat_func_one_chain: for chain 0
2021-04-14 12:23:04 dspic33ep16gs202.c:409:hashboard_power_cntl: [0] ok, i2c=0!
2021-04-14 12:23:05 dspic33ep16gs202.c:409:hashboard_power_cntl: [0] ok, i2c=2!
2021-04-14 12:23:08 driver-btm-soc.c:8241:bitmain_soc_init: Enter 30s sleep to make sure power release finish.
2021-04-14 12:23:38 driver-btm-soc.c:7626:set_working_voltage_by_eeprom: eeprom voltage[0] = 19.300000
2021-04-14 12:23:38 driver-btm-soc.c:7626:set_working_voltage_by_eeprom: eeprom voltage[2] = 19.300000
2021-04-14 12:23:38 driver-btm-soc.c:7630:set_working_voltage_by_eeprom: max = 19.30, min = 19.30
2021-04-14 12:23:38 power.c:149:set_working_voltage: working_voltage = 19.300000
2021-04-14 12:23:38 power.c:274:set_iic_power_to_highest_voltage: setting to voltage: 20.00 ...
2021-04-14 12:23:38 power.c:227:set_iic_power_by_voltage: now setting voltage to : 20.000000
2021-04-14 12:23:38 eeprom.c:840:travel_eeprom_store: chain[0] data in eeprom is:
magic number: 0x7f
freq data per ASIC:
IC[000]:450 IC[001]:450 IC[002]:450 IC[003]:450 IC[004]:420
IC[005]:420 IC[006]:450 IC[007]:450 IC[008]:450 IC[009]:450
IC[010]:420 IC[011]:450 IC[012]:450 IC[013]:450 IC[014]:450
IC[015]:450 IC[016]:450 IC[017]:420 IC[018]:450 IC[019]:450
IC[020]:450 IC[021]:420 IC[022]:450 IC[023]:450 IC[024]:450
IC[025]:450 IC[026]:420 IC[027]:450 IC[028]:450 IC[029]:450
IC[030]:450 IC[031]:450 IC[032]:450 IC[033]:450 IC[034]:420
IC[035]:420 IC[036]:450 IC[037]:450 IC[038]:450 IC[039]:450
IC[040]:420 IC[041]:450 IC[042]:450 IC[043]:450 IC[044]:450
IC[045]:450 IC[046]:450 IC[047]:420 IC[048]:450 IC[049]:450
IC[050]:450 IC[051]:450 IC[052]:420 IC[053]:450 IC[054]:450
IC[055]:450 IC[056]:450 IC[057]:450 IC[058]:450 IC[059]:420
voltage: 18.60 V
hash rate: 06797 GH/s
freq data per ASIC in mode2:
IC[000]:510 IC[001]:510 IC[002]:510 IC[003]:510 IC[004]:480
IC[005]:480 IC[006]:510 IC[007]:510 IC[008]:510 IC[009]:510
IC[010]:480 IC[011]:510 IC[012]:510 IC[013]:510 IC[014]:510
IC[015]:510 IC[016]:510 IC[017]:480 IC[018]:510 IC[019]:510
IC[020]:510 IC[021]:480 IC[022]:510 IC[023]:510 IC[024]:510
IC[025]:510 IC[026]:480 IC[027]:510 IC[028]:510 IC[029]:510
IC[030]:510 IC[031]:510 IC[032]:510 IC[033]:480 IC[034]:510
IC[035]:480 IC[036]:510 IC[037]:510 IC[038]:510 IC[039]:510
IC[040]:480 IC[041]:510 IC[042]:510 IC[043]:510 IC[044]:510
IC[045]:510 IC[046]:510 IC[047]:510 IC[048]:480 IC[049]:510
IC[050]:510 IC[051]:510 IC[052]:480 IC[053]:510 IC[054]:510
IC[055]:510 IC[056]:510 IC[057]:510 IC[058]:510 IC[059]:480
voltage in mode2: 19.30 V
hash rate in mode2: 07703 GH/s
2021-04-14 12:23:38 eeprom.c:840:travel_eeprom_store: chain[2] data in eeprom is:
magic number: 0x7f
freq data per ASIC:
IC[000]:465 IC[001]:450 IC[002]:435 IC[003]:465 IC[004]:465
IC[005]:465 IC[006]:435 IC[007]:465 IC[008]:465 IC[009]:450
IC[010]:435 IC[011]:465 IC[012]:465 IC[013]:450 IC[014]:465
IC[015]:450 IC[016]:465 IC[017]:465 IC[018]:465 IC[019]:435
IC[020]:465 IC[021]:465 IC[022]:465 IC[023]:435 IC[024]:450
IC[025]:465 IC[026]:435 IC[027]:450 IC[028]:465 IC[029]:465
IC[030]:465 IC[031]:450 IC[032]:435 IC[033]:465 IC[034]:465
IC[035]:435 IC[036]:465 IC[037]:450 IC[038]:465 IC[039]:465
IC[040]:465 IC[041]:465 IC[042]:450 IC[043]:435 IC[044]:465
IC[045]:465 IC[046]:465 IC[047]:435 IC[048]:465 IC[049]:450
IC[050]:465 IC[051]:465 IC[052]:450 IC[053]:435 IC[054]:465
IC[055]:450 IC[056]:435 IC[057]:465 IC[058]:465 IC[059]:465
voltage: 18.60 V
hash rate: 06987 GH/s
freq data per ASIC in mode2:
IC[000]:510 IC[001]:510 IC[002]:510 IC[003]:495 IC[004]:510
IC[005]:510 IC[006]:495 IC[007]:510 IC[008]:510 IC[009]:510
IC[010]:495 IC[011]:510 IC[012]:510 IC[013]:510 IC[014]:510
IC[015]:510 IC[016]:510 IC[017]:510 IC[018]:510 IC[019]:495
IC[020]:510 IC[021]:495 IC[022]:510 IC[023]:510 IC[024]:510
IC[025]:510 IC[026]:495 IC[027]:510 IC[028]:510 IC[029]:510
IC[030]:510 IC[031]:495 IC[032]:510 IC[033]:510 IC[034]:510
IC[035]:495 IC[036]:510 IC[037]:510 IC[038]:510 IC[039]:510
IC[040]:510 IC[041]:510 IC[042]:510 IC[043]:495 IC[044]:510
IC[045]:510 IC[046]:510 IC[047]:495 IC[048]:510 IC[049]:510
IC[050]:495 IC[051]:510 IC[052]:510 IC[053]:510 IC[054]:510
IC[055]:510 IC[056]:495 IC[057]:510 IC[058]:510 IC[059]:510
voltage in mode2: 19.30 V
hash rate in mode2: 07752 GH/s
2021-04-14 12:23:39 dspic33ep16gs202.c:409:hashboard_power_cntl: [1] ok, i2c=0!
2021-04-14 12:23:39 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-04-14 12:23:42 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-04-14 12:23:45 driver-btm-soc.c:5456:check_asic_num_by_pre_open_core: Try to find asic by pre core: times 0
2021-04-14 12:23:45 driver-btm-soc.c:5412:check_asic_num_without_power_off: Open 16 core for chain 0
2021-04-14 12:23:45 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 16
2021-04-14 12:23:46 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:23:46 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 16
2021-04-14 12:23:46 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:23:46 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 16
2021-04-14 12:23:47 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:23:47 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 16
2021-04-14 12:23:48 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:23:48 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-04-14 12:23:51 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-04-14 12:23:55 driver-btm-soc.c:5426:check_asic_num_without_power_off: chain 0, find asic num = 0
2021-04-14 12:23:55 driver-btm-soc.c:5412:check_asic_num_without_power_off: Open 32 core for chain 0
2021-04-14 12:23:55 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 32
2021-04-14 12:23:57 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:23:57 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 32
2021-04-14 12:23:58 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:23:58 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 32
2021-04-14 12:23:59 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:23:59 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 32
2021-04-14 12:24:01 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:24:01 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-04-14 12:24:04 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-04-14 12:24:08 driver-btm-soc.c:5426:check_asic_num_without_power_off: chain 0, find asic num = 0
2021-04-14 12:24:08 driver-btm-soc.c:5412:check_asic_num_without_power_off: Open 64 core for chain 0
2021-04-14 12:24:08 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 64
2021-04-14 12:24:11 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:24:11 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 64
2021-04-14 12:24:14 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:24:14 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 64
2021-04-14 12:24:17 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:24:17 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 64
2021-04-14 12:24:20 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:24:20 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-04-14 12:24:23 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-04-14 12:24:27 driver-btm-soc.c:5426:check_asic_num_without_power_off: chain 0, find asic num = 0
2021-04-14 12:24:27 driver-btm-soc.c:5466:check_asic_num_by_pre_open_core: Unable to find all asic [0] times, power off hash board and wait [30] sec
2021-04-14 12:24:28 dspic33ep16gs202.c:409:hashboard_power_cntl: [0] ok, i2c=0!
2021-04-14 12:24:58 power.c:274:set_iic_power_to_highest_voltage: setting to voltage: 20.00 ...
2021-04-14 12:24:58 power.c:227:set_iic_power_by_voltage: now setting voltage to : 20.000000
2021-04-14 12:24:59 dspic33ep16gs202.c:409:hashboard_power_cntl: [1] ok, i2c=0!
2021-04-14 12:25:01 driver-btm-soc.c:5456:check_asic_num_by_pre_open_core: Try to find asic by pre core: times 1
2021-04-14 12:25:01 driver-btm-soc.c:5412:check_asic_num_without_power_off: Open 16 core for chain 0
2021-04-14 12:25:01 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 16
2021-04-14 12:25:02 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:25:02 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 16
2021-04-14 12:25:02 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:25:02 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 16
2021-04-14 12:25:03 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:25:03 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 16
2021-04-14 12:25:04 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:25:04 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-04-14 12:25:07 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-04-14 12:25:11 driver-btm-soc.c:5426:check_asic_num_without_power_off: chain 0, find asic num = 0
2021-04-14 12:25:11 driver-btm-soc.c:5412:check_asic_num_without_power_off: Open 32 core for chain 0
2021-04-14 12:25:11 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 32
2021-04-14 12:25:13 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:25:13 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 32
2021-04-14 12:25:14 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:25:14 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 32
2021-04-14 12:25:16 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:25:16 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 32
2021-04-14 12:25:17 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:25:17 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-04-14 12:25:20 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-04-14 12:25:24 driver-btm-soc.c:5426:check_asic_num_without_power_off: chain 0, find asic num = 0
2021-04-14 12:25:24 driver-btm-soc.c:5412:check_asic_num_without_power_off: Open 64 core for chain 0
2021-04-14 12:25:24 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 64
2021-04-14 12:25:27 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:25:27 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 64
2021-04-14 12:25:30 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:25:30 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 64
2021-04-14 12:25:33 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:25:33 driver-btm-soc.c:3992:open_core_BM1391_pre_open: pre open core = 64
2021-04-14 12:25:36 driver-btm-soc.c:3967:pre_open_core_one_chain: for chain 0
2021-04-14 12:25:36 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000ffff
2021-04-14 12:25:39 znyq.c:193:set_reset_hashboard: set_reset_hashboard = 0x0000fffe
2021-04-14 12:25:43 driver-btm-soc.c:5426:check_asic_num_without_power_off: chain 0, find asic num = 0
2021-04-14 12:25:43 driver-btm-soc.c:5466:check_asic_num_by_pre_open_core: Unable to find all asic [1] times, power off hash board and wait [30] sec
2021-04-14 12:25:44 dspic33ep16gs202.c:409:hashboard_power_cntl: [0] ok, i2c=0! |
|
|
|
|
Just doesn't seem to "kick in" while running. No stats displayed at all.
|
|
|
|
Wondering whether my T15 is completely dead or if it needs a new main board. Can anyone tell from this log? Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 197340K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 32036K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 18996K (cc873000 - cdb00000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
nand_read_bbt: bad block at 0x000002420000
nand_read_bbt: bad block at 0x000002440000
nand_read_bbt: bad block at 0x000002460000
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 17/7, WL threshold: 4096, image sequence number: 131776731
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID AD63E5E5-DA5C-4DAD-9550-959A80DA7C1B, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 3652/898, WL threshold: 4096, image sequence number: 267841159
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 31AA9D87-7438-4BA5-AB48-E0CFF57D9D53, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab01b
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
[2021-04-09 15:32:44.984] start listen on 6060 ...
2021-04-09 15:49:22 driver-btm-soc.c:7273:init_freq_mode: This is scan-user version
2021-04-09 15:49:22 driver-btm-soc.c:8125:bitmain_soc_init: T15
2021-04-09 15:49:22 driver-btm-soc.c:8126:bitmain_soc_init: opt_multi_version=1
2021-04-09 15:49:22 driver-btm-soc.c:8127:bitmain_soc_init: opt_bitmain_ab=1
2021-04-09 15:49:22 driver-btm-soc.c:8128:bitmain_soc_init: opt_bitmain_economic_mode=false
2021-04-09 15:49:22 driver-btm-soc.c:8129:bitmain_soc_init: opt_bitmain_work_mode_test = 0
2021-04-09 15:49:22 driver-btm-soc.c:7682:_show_sn: no SN got, please write SN to /nvdata/sn
2021-04-09 15:49:22 driver-btm-soc.c:7304:init_phy_mem_nonce2_jobid_address: Detect 256MB control board of XILINX
2021-04-09 15:49:22 driver-btm-soc.c:8149:bitmain_soc_init: Miner compile time: Fri Dec 13 15:46:16 CST 2019 type: Antminer T15
2021-04-09 15:49:22 driver-btm-soc.c:8151:bitmain_soc_init: last commit version: 53156cb commit time: 2019-11-06 10:21:42 build: 2019-12-13 15:53:57
2021-04-09 15:49:22 driver-btm-soc.c:7336:check_fan_multi: check fan for 20 times...
2021-04-09 15:49:24 driver-btm-soc.c:8214:bitmain_soc_init: miner ID : 8074f42429e04814
2021-04-09 15:49:24 driver-btm-soc.c:7410:init_miner_version: FPGA Version = 0xB01B
2021-04-09 15:49:24 driver-btm-soc.c:1092:check_chain: get_hash_on_plug is 0x7
2021-04-09 15:49:24 driver-btm-soc.c:1104:check_chain: !! chain[0]is exist
2021-04-09 15:49:24 driver-btm-soc.c:1104:check_chain: !! chain[1]is exist
2021-04-09 15:49:24 driver-btm-soc.c:1104:check_chain: !! chain[2]is exist
2021-04-09 15:49:31 eeprom.c:1418:eeprom_load: done
2021-04-09 15:49:31 driver-btm-soc.c:7431:init_pcb_version: chain[0] PCB Version : 0x0101
2021-04-09 15:49:31 driver-btm-soc.c:7449:init_pcb_version: chain[0] BOM Version : 0x0100
2021-04-09 15:49:31 driver-btm-soc.c:7431:init_pcb_version: chain[1] PCB Version : 0x0101
2021-04-09 15:49:31 driver-btm-soc.c:7449:init_pcb_version: chain[1] BOM Version : 0x0100
2021-04-09 15:49:31 driver-btm-soc.c:7431:init_pcb_version: chain[2] PCB Version : 0x0101
2021-04-09 15:49:31 driver-btm-soc.c:7449:init_pcb_version: chain[2] BOM Version : 0x0100
2021-04-09 15:49:32 dspic33ep16gs202.c:538:reset_pic: chain[0] ok
2021-04-09 15:49:36 dspic33ep16gs202.c:504:jump_to_app_from_loader: chain[0] ok
2021-04-09 15:49:37 dspic33ep16gs202.c:538:reset_pic: chain[1] ok
2021-04-09 15:49:42 dspic33ep16gs202.c:504:jump_to_app_from_loader: chain[1] ok
2021-04-09 15:49:42 dspic33ep16gs202.c:538:reset_pic: chain[2] ok |
|
|
|
|
I have to build a concrete base for a summer house in my garden. I had a bit of an idea that I might dig down and actually build a concrete bunker underneath while I was at it, in order to house some miners. Just wanted to find out whether anyone has actually done this themselves, and what solutions they had for heat, air, soundproofing? Electricity and internet connection should be easy enough.
Or is it an unfeasible idea?
|
|
|
|
I absolutely did get that trick from you  It was one of the very few things I could do myself to try to solve the problem, without sending it to someone else. I am really grateful for the help!! |
|
|
|
|
Thanks for all the help on my problems. I took the boards out and pushed in the heatsinks etc. Worked beautifully! All working at 100% now.
|
|
|
|
Thanks for your patience  I realise that I'm probably asking questions that will make people want to pull their hair out. Once I get it, I'll be able to just leave it running. I've downloaded those files, and there are 3 sets. My miner is an S17-53T so I'm not sure which of these to use, as they don't match the filename precisely? |
|
|
|
[...]
Thanks, will check it out.
This may well be another stupid question, but I downloaded what I think is the firmware for the S17 and put it on a microSD card. I put it in and switched it on, but all I get is the two lights steadily on. Which is the right one to flash the firmware? Maybe I'm using the wrong one. The instructions on the Bitmain site are not helpful. |
|
|
|
And this is after. The hashrate dropped to zero in this section. 2020-06-19 21:44:43 driver-btm-api.c:197:set_miner_status: WARN_NET_LOST
2020-06-19 21:44:44 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
2020-06-19 21:44:52 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
2020-06-19 21:44:58 log.c:100:_log_update_name: _log_update_name
2020-06-19 21:44:58 log.c:100:_log_update_name: _log_update_name
2020-06-19 21:45:05 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
2020-06-19 21:45:12 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
2020-06-19 21:45:13 driver-btm-api.c:197:set_miner_status: STATUS_OKAY
2020-06-19 21:45:25 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
2020-06-19 21:45:32 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
2020-06-19 21:45:45 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
2020-06-19 21:45:51 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
2020-06-19 21:46:04 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
2020-06-19 21:46:13 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
2020-06-19 21:46:26 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
2020-06-19 21:46:33 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
2020-06-19 21:46:46 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
2020-06-19 21:46:52 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
2020-06-19 21:47:06 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
2020-06-19 21:47:12 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
2020-06-19 21:47:25 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
2020-06-19 21:47:34 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
2020-06-19 21:47:47 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
2020-06-19 21:47:54 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
2020-06-19 21:48:07 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
2020-06-19 21:48:13 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
2020-06-19 21:48:26 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
2020-06-19 21:48:33 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
2020-06-19 21:48:46 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
2020-06-19 21:48:55 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
2020-06-19 21:49:08 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
2020-06-19 21:49:14 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
2020-06-19 21:49:27 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
2020-06-19 21:49:34 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
2020-06-19 21:49:47 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
2020-06-19 21:49:54 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
2020-06-19 21:50:07 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
2020-06-19 21:50:15 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
2020-06-19 21:50:28 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
2020-06-19 21:50:35 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
2020-06-19 21:50:48 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
2020-06-19 21:50:55 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
2020-06-19 21:51:08 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
2020-06-19 21:51:14 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
2020-06-19 21:51:27 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
2020-06-19 21:51:36 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
2020-06-19 21:51:49 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
2020-06-19 21:51:56 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
2020-06-19 21:52:09 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
2020-06-19 21:52:15 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
2020-06-19 21:52:28 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
2020-06-19 21:52:35 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
2020-06-19 21:52:48 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
2020-06-19 21:52:57 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
2020-06-19 21:53:10 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
2020-06-19 21:53:16 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
2020-06-19 21:53:29 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
2020-06-19 21:53:36 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
2020-06-19 21:53:49 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
2020-06-19 21:53:56 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
2020-06-19 21:54:09 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
2020-06-19 21:54:17 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
2020-06-19 21:54:31 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
2020-06-19 21:54:37 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
2020-06-19 21:54:50 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
2020-06-19 21:54:57 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
2020-06-19 21:55:10 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
2020-06-19 21:55:16 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
2020-06-19 21:55:30 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
2020-06-19 21:55:38 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
2020-06-19 21:55:51 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
2020-06-19 21:55:58 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
2020-06-19 21:56:11 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
2020-06-19 21:56:18 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
2020-06-19 21:56:31 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
2020-06-19 21:56:37 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
2020-06-19 21:56:50 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
2020-06-19 21:56:59 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
2020-06-19 21:57:12 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
2020-06-19 21:57:19 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
2020-06-19 21:57:32 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
2020-06-19 21:57:38 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
2020-06-19 21:57:51 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
2020-06-19 21:57:58 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
2020-06-19 21:58:11 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
2020-06-19 21:58:20 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
2020-06-19 21:58:33 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
2020-06-19 21:58:39 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
2020-06-19 21:58:52 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
2020-06-19 21:58:59 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
2020-06-19 21:59:12 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
2020-06-19 21:59:19 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
2020-06-19 21:59:32 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
2020-06-19 21:59:40 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
2020-06-19 21:59:54 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
2020-06-19 22:00:00 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
2020-06-19 22:00:13 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
2020-06-19 22:00:20 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
2020-06-19 22:00:33 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
2020-06-19 22:00:39 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
2020-06-19 22:00:53 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
2020-06-19 22:01:01 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
2020-06-19 22:01:14 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
2020-06-19 22:01:21 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
2020-06-19 22:01:34 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
2020-06-19 22:01:40 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
2020-06-19 22:01:53 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
2020-06-19 22:02:00 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
2020-06-19 22:02:13 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
2020-06-19 22:02:22 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
2020-06-19 22:02:35 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
2020-06-19 22:02:41 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
2020-06-19 22:02:54 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
2020-06-19 22:03:01 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
2020-06-19 22:03:14 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
2020-06-19 22:03:21 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
2020-06-19 22:03:34 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
2020-06-19 22:03:42 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
2020-06-19 22:03:55 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
2020-06-19 22:04:02 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
2020-06-19 22:04:15 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
2020-06-19 22:04:22 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
2020-06-19 22:04:35 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
2020-06-19 22:04:41 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
2020-06-19 22:04:54 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
2020-06-19 22:05:03 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
2020-06-19 22:05:16 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
2020-06-19 22:05:23 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
2020-06-19 22:05:36 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
2020-06-19 22:05:42 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
2020-06-19 22:05:55 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
2020-06-19 22:06:02 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
2020-06-19 22:06:15 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
2020-06-19 22:06:24 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
2020-06-19 22:06:37 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
2020-06-19 22:06:43 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
2020-06-19 22:06:56 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
2020-06-19 22:07:03 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
2020-06-19 22:07:16 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
2020-06-19 22:07:23 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
2020-06-19 22:07:36 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
2020-06-19 22:07:44 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
2020-06-19 22:07:58 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
2020-06-19 22:08:04 thread.c:221:calc_hashrate_avg: avg rate is 37667.44 in 30 mins
2020-06-19 22:08:04 temperature.c:449:temp_statistics_show: pcb temp 32~50 chip temp 55~69
2020-06-19 22:08:04 thread.c:302:check_hashrate: latest avg rate < 0.98......
2020-06-19 22:08:04 thread.c:303:check_hashrate: current PCB min temperature 32
2020-06-19 22:08:04 thread.c:304:check_hashrate: current voltage raw is 1900, working voltage raw is 1820
2020-06-19 22:08:04 thread.c:335:check_hashrate: high temp, increase voltage 0.1V/0.2V to 1910
2020-06-19 22:08:04 driver-btm-api.c:1996:bitmain_reopen_core: reopen_core start!
2020-06-19 22:08:04 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
2020-06-19 22:08:17 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
2020-06-19 22:08:24 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
2020-06-19 22:08:37 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
2020-06-19 22:08:43 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
2020-06-19 22:08:57 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
2020-06-19 22:09:04 driver-btm-api.c:945:init_miner_version: miner ID : 800864467910481c
2020-06-19 22:09:04 driver-btm-api.c:951:init_miner_version: FPGA Version = 0xB013
2020-06-19 22:09:09 driver-btm-api.c:589:get_product_id: product_id[0] = 0
2020-06-19 22:09:09 driver-btm-api.c:589:get_product_id: product_id[1] = 0
2020-06-19 22:09:09 driver-btm-api.c:589:get_product_id: product_id[2] = 0
2020-06-19 22:09:09 driver-btm-api.c:533:_set_project_type: project:1
2020-06-19 22:09:09 driver-btm-api.c:558:_set_project_type: Project type: Antminer S17
2020-06-19 22:09:09 driver-btm-api.c:569:dump_pcb_bom_version: Chain [0] PCB Version: 0x0101
2020-06-19 22:09:09 driver-btm-api.c:570:dump_pcb_bom_version: Chain [0] BOM Version: 0x0103
2020-06-19 22:09:09 driver-btm-api.c:569:dump_pcb_bom_version: Chain [1] PCB Version: 0x0101
2020-06-19 22:09:09 driver-btm-api.c:570:dump_pcb_bom_version: Chain [1] BOM Version: 0x0103
2020-06-19 22:09:09 driver-btm-api.c:569:dump_pcb_bom_version: Chain [2] PCB Version: 0x0101
2020-06-19 22:09:09 driver-btm-api.c:570:dump_pcb_bom_version: Chain [2] BOM Version: 0x0103
2020-06-19 22:09:10 driver-btm-api.c:1785:bitmain_board_init: Fan check passed.
2020-06-19 22:09:11 register.c:283:get_register: !!! reg crc error
2020-06-19 22:09:12 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2020-06-19 22:09:14 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
2020-06-19 22:09:15 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2020-06-19 22:09:17 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
2020-06-19 22:09:18 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2020-06-19 22:09:20 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
2020-06-19 22:09:20 power_api.c:207:power_init: Power init:
2020-06-19 22:09:20 power_api.c:208:power_init: current_voltage_raw = 0
2020-06-19 22:09:20 power_api.c:209:power_init: highest_voltage_raw = 2100
2020-06-19 22:09:20 power_api.c:210:power_init: working_voltage_raw = 1830
2020-06-19 22:09:20 power_api.c:211:power_init: higher_voltage_raw = 1950
2020-06-19 22:09:20 driver-btm-api.c:1795:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2020-06-19 22:09:52 power_api.c:251:set_to_highest_voltage: Set to voltage raw 2100, one step.
2020-06-19 22:09:54 power_api.c:87:check_voltage_multi: retry time: 0
2020-06-19 22:09:55 power_api.c:37:_get_avg_voltage: chain = 0, voltage = 21.063281
2020-06-19 22:09:56 power_api.c:37:_get_avg_voltage: chain = 1, voltage = 21.069404
2020-06-19 22:09:57 power_api.c:37:_get_avg_voltage: chain = 2, voltage = 21.044912
2020-06-19 22:09:57 power_api.c:50:_get_avg_voltage: average_voltage = 21.059199
2020-06-19 22:09:57 power_api.c:68:check_voltage: target_vol = 21.00, actural_vol = 21.06, check voltage passed.
2020-06-19 22:09:57 uart.c:71:set_baud: set fpga_baud to 115200
2020-06-19 22:09:57 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-06-19 22:09:57 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-06-19 22:09:57 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-06-19 22:10:09 driver-btm-api.c:888:check_asic_number_with_power_on: Chain[0]: find 47 asic, times 0
2020-06-19 22:10:20 driver-btm-api.c:888:check_asic_number_with_power_on: Chain[0]: find 48 asic, times 1
2020-06-19 22:10:31 driver-btm-api.c:888:check_asic_number_with_power_on: Chain[1]: find 48 asic, times 0
2020-06-19 22:10:42 driver-btm-api.c:888:check_asic_number_with_power_on: Chain[2]: find 48 asic, times 0
2020-06-19 22:10:47 driver-btm-api.c:344:set_order_clock: chain[0]: set order clock, stragegy 3
2020-06-19 22:10:47 driver-btm-api.c:344:set_order_clock: chain[1]: set order clock, stragegy 3
2020-06-19 22:10:47 driver-btm-api.c:344:set_order_clock: chain[2]: set order clock, stragegy 3
2020-06-19 22:10:47 driver-hash-chip.c:502:set_clock_delay_control: core_data = 0x34
2020-06-19 22:10:47 uart.c:71:set_baud: set fpga_baud to 3000000
2020-06-19 22:10:47 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
2020-06-19 22:10:47 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[1]: chip baud = 3000000, chip_divider = 0
2020-06-19 22:10:47 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[2]: chip baud = 3000000, chip_divider = 0
2020-06-19 22:10:47 driver-btm-api.c:1547:check_clock_counter: freq 50 clock_counter_limit 6
2020-06-19 22:10:49 uart.c:71:set_baud: set fpga_baud to 115200
2020-06-19 22:10:49 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
2020-06-19 22:10:49 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
2020-06-19 22:10:49 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
2020-06-19 22:10:49 voltage[0] = 1820
2020-06-19 22:10:49 voltage[1] = 1820
2020-06-19 22:10:49 voltage[2] = 1820
2020-06-19 22:10:49 power_api.c:219:set_working_voltage_raw: working_voltage_raw = 1820
2020-06-19 22:10:50 frequency.c:196:get_ideal_hash_rate_GH: ideal_hash_rate = 55249
2020-06-19 22:10:50 frequency.c:212:get_sale_hash_rate_GH: sale_hash_rate = 53000
2020-06-19 22:10:51 temperature.c:281:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
2020-06-19 22:10:52 temperature.c:281:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
2020-06-19 22:10:53 temperature.c:281:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 2 success.
2020-06-19 22:10:53 uart.c:71:set_baud: set fpga_baud to 6000000
2020-06-19 22:10:53 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
2020-06-19 22:10:53 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[1]: chip baud = 6000000, chip_divider = 7
2020-06-19 22:10:53 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[2]: chip baud = 6000000, chip_divider = 7
2020-06-19 22:10:55 driver-btm-api.c:244:check_bringup_temp: Bring up temperature is 23
2020-06-19 22:10:55 frequency.c:711:inc_freq_with_fixed_vco: chain = 255, freq = 555, is_higher_voltage = true
2020-06-19 22:10:55 power_api.c:287:set_to_voltage_by_steps: Set to voltage raw 2020, step by step.
2020-06-19 22:11:14 power_api.c:87:check_voltage_multi: retry time: 0
2020-06-19 22:11:15 power_api.c:37:_get_avg_voltage: chain = 0, voltage = 20.218301
2020-06-19 22:11:16 power_api.c:37:_get_avg_voltage: chain = 1, voltage = 20.255039
2020-06-19 22:11:17 power_api.c:37:_get_avg_voltage: chain = 2, voltage = 20.212177
2020-06-19 22:11:17 power_api.c:50:_get_avg_voltage: average_voltage = 20.228506
2020-06-19 22:11:17 power_api.c:68:check_voltage: target_vol = 20.20, actural_vol = 20.23, check voltage passed. |
|
|
|
This is the initial state before the clock sets: Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203620K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25756K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12716K (cce95000 - cdb00000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAGAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 15/7, WL threshold: 4096, image sequence number: 2419912869
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 1303F5C2-F3EF-4059-9B98-C469B28B1788, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 4/1, WL threshold: 4096, image sequence number: 2324953515
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 8C5051EC-2BDF-4773-B69A-558999E9CEC7, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
macb e000b000.ethernet eth0: link down
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xab013
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
macb e000b000.ethernet eth0: link down
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
random: nonblocking pool is initialized
1970-01-01 00:05:16 driver-btm-api.c:515:init_freq_mode: This is scan-user version
1970-01-01 00:05:16 driver-btm-api.c:1871:bitmain_soc_init: opt_multi_version = 1
1970-01-01 00:05:16 driver-btm-api.c:1872:bitmain_soc_init: opt_bitmain_ab = 1
1970-01-01 00:05:16 driver-btm-api.c:1873:bitmain_soc_init: opt_bitmain_work_mode = 2
1970-01-01 00:05:16 driver-btm-api.c:1874:bitmain_soc_init: Miner compile time: Wed Dec 25 09:45:06 CST 2019 type: Antminer S17
1970-01-01 00:05:16 driver-btm-api.c:1875:bitmain_soc_init: commit version: b1e11d0 2019-12-24 22:26:20, build by: lol 2019-12-25 09:54:26
1970-01-01 00:05:16 driver-btm-api.c:1664:show_sn: no SN got, please write SN to /nvdata/sn
1970-01-01 00:05:16 driver-btm-api.c:1013:miner_device_init: Detect 256MB control board of XILINX
1970-01-01 00:05:16 driver-btm-api.c:961:init_fan_parameter: fan_eft : 0 fan_pwm : 0
1970-01-01 00:05:22 driver-btm-api.c:945:init_miner_version: miner ID : 800864467910481c
1970-01-01 00:05:22 driver-btm-api.c:951:init_miner_version: FPGA Version = 0xB013
1970-01-01 00:05:27 thread.c:699:create_read_nonce_reg_thread: create thread
1970-01-01 00:05:27 driver-btm-api.c:589:get_product_id: product_id[0] = 0
1970-01-01 00:05:27 driver-btm-api.c:589:get_product_id: product_id[1] = 0
1970-01-01 00:05:27 driver-btm-api.c:589:get_product_id: product_id[2] = 0
1970-01-01 00:05:27 driver-btm-api.c:533:_set_project_type: project:1
1970-01-01 00:05:27 driver-btm-api.c:558:_set_project_type: Project type: Antminer S17
1970-01-01 00:05:27 driver-btm-api.c:569:dump_pcb_bom_version: Chain [0] PCB Version: 0x0101
1970-01-01 00:05:27 driver-btm-api.c:570:dump_pcb_bom_version: Chain [0] BOM Version: 0x0103
1970-01-01 00:05:27 driver-btm-api.c:569:dump_pcb_bom_version: Chain [1] PCB Version: 0x0101
1970-01-01 00:05:27 driver-btm-api.c:570:dump_pcb_bom_version: Chain [1] BOM Version: 0x0103
1970-01-01 00:05:27 driver-btm-api.c:569:dump_pcb_bom_version: Chain [2] PCB Version: 0x0101
1970-01-01 00:05:27 driver-btm-api.c:570:dump_pcb_bom_version: Chain [2] BOM Version: 0x0103
1970-01-01 00:05:28 driver-btm-api.c:1785:bitmain_board_init: Fan check passed.
1970-01-01 00:05:29 board.c:36:jump_and_app_check_restore_pic: chain[0] PIC jump to app
1970-01-01 00:05:31 board.c:40:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0xb9
1970-01-01 00:05:33 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
1970-01-01 00:05:35 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0xb9
1970-01-01 00:05:36 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
1970-01-01 00:05:38 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0xb9
1970-01-01 00:05:38 thread.c:694:create_pic_heart_beat_thread: create thread
1970-01-01 00:05:38 power_api.c:207:power_init: Power init:
1970-01-01 00:05:38 power_api.c:208:power_init: current_voltage_raw = 0
1970-01-01 00:05:38 power_api.c:209:power_init: highest_voltage_raw = 2100
1970-01-01 00:05:38 power_api.c:210:power_init: working_voltage_raw = 1830
1970-01-01 00:05:38 power_api.c:211:power_init: higher_voltage_raw = 1950
1970-01-01 00:05:38 driver-btm-api.c:1795:bitmain_board_init: Enter 30s sleep to make sure power release finish.
1970-01-01 00:06:10 power_api.c:251:set_to_highest_voltage: Set to voltage raw 2100, one step.
1970-01-01 00:06:12 power_api.c:87:check_voltage_multi: retry time: 0
1970-01-01 00:06:13 power_api.c:37:_get_avg_voltage: chain = 0, voltage = 21.020420
1970-01-01 00:06:14 power_api.c:37:_get_avg_voltage: chain = 1, voltage = 21.057158
1970-01-01 00:06:15 power_api.c:37:_get_avg_voltage: chain = 2, voltage = 21.032666
1970-01-01 00:06:15 power_api.c:50:_get_avg_voltage: average_voltage = 21.036748
1970-01-01 00:06:15 power_api.c:68:check_voltage: target_vol = 21.00, actural_vol = 21.04, check voltage passed.
1970-01-01 00:06:15 uart.c:71:set_baud: set fpga_baud to 115200
1970-01-01 00:06:15 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
1970-01-01 00:06:15 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
1970-01-01 00:06:15 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
1970-01-01 00:06:26 driver-btm-api.c:888:check_asic_number_with_power_on: Chain[0]: find 48 asic, times 0
1970-01-01 00:06:37 driver-btm-api.c:888:check_asic_number_with_power_on: Chain[1]: find 48 asic, times 0
1970-01-01 00:06:48 driver-btm-api.c:888:check_asic_number_with_power_on: Chain[2]: find 48 asic, times 0
1970-01-01 00:06:53 driver-btm-api.c:344:set_order_clock: chain[0]: set order clock, stragegy 3
1970-01-01 00:06:54 driver-btm-api.c:344:set_order_clock: chain[1]: set order clock, stragegy 3
1970-01-01 00:06:54 driver-btm-api.c:344:set_order_clock: chain[2]: set order clock, stragegy 3
1970-01-01 00:06:54 driver-hash-chip.c:502:set_clock_delay_control: core_data = 0x34
1970-01-01 00:06:54 uart.c:71:set_baud: set fpga_baud to 3000000
1970-01-01 00:06:54 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[0]: chip baud = 3000000, chip_divider = 0
1970-01-01 00:06:54 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[1]: chip baud = 3000000, chip_divider = 0
1970-01-01 00:06:54 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[2]: chip baud = 3000000, chip_divider = 0
1970-01-01 00:06:54 driver-btm-api.c:1547:check_clock_counter: freq 50 clock_counter_limit 6
1970-01-01 00:06:56 driver-btm-api.c:1537:clear_bad_clock_mark: clock counter check pass.
1970-01-01 00:06:56 uart.c:71:set_baud: set fpga_baud to 115200
1970-01-01 00:06:56 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[0]: chip baud = 115200, chip_divider = 26
1970-01-01 00:06:56 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[1]: chip baud = 115200, chip_divider = 26
1970-01-01 00:06:56 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[2]: chip baud = 115200, chip_divider = 26
1970-01-01 00:06:56 voltage[0] = 1820
1970-01-01 00:06:56 voltage[1] = 1820
1970-01-01 00:06:56 voltage[2] = 1820
1970-01-01 00:06:56 power_api.c:219:set_working_voltage_raw: working_voltage_raw = 1820
1970-01-01 00:06:57 temperature.c:281:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 0 success.
1970-01-01 00:06:59 temperature.c:281:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 1 success.
1970-01-01 00:07:00 temperature.c:281:calibrate_temp_sensor_one_chain: Temperature sensor calibration: chain 2 success.
1970-01-01 00:07:00 uart.c:71:set_baud: set fpga_baud to 6000000
1970-01-01 00:07:00 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[0]: chip baud = 6000000, chip_divider = 7
1970-01-01 00:07:00 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[1]: chip baud = 6000000, chip_divider = 7
1970-01-01 00:07:00 driver-hash-chip.c:245:dhash_chip_set_baud_v2: chain[2]: chip baud = 6000000, chip_divider = 7
1970-01-01 00:07:02 driver-btm-api.c:244:check_bringup_temp: Bring up temperature is 18
1970-01-01 00:07:02 thread.c:714:create_check_miner_status_thread: create thread
1970-01-01 00:07:02 thread.c:704:create_set_miner_status_thread: create thread
1970-01-01 00:07:02 thread.c:689:create_temperature_monitor_thread: create thread
1970-01-01 00:07:02 freq_tuning.c:195:freq_tuning_get_max_freq: Max freq of tuning is 780
1970-01-01 00:07:02 frequency.c:711:inc_freq_with_fixed_vco: chain = 255, freq = 555, is_higher_voltage = true
1970-01-01 00:07:02 power_api.c:287:set_to_voltage_by_steps: Set to voltage raw 2020, step by step.
1970-01-01 00:07:20 power_api.c:87:check_voltage_multi: retry time: 0
1970-01-01 00:07:21 power_api.c:37:_get_avg_voltage: chain = 0, voltage = 20.193808
1970-01-01 00:07:22 power_api.c:37:_get_avg_voltage: chain = 1, voltage = 20.224424
1970-01-01 00:07:23 power_api.c:37:_get_avg_voltage: chain = 2, voltage = 20.212177
1970-01-01 00:07:23 power_api.c:50:_get_avg_voltage: average_voltage = 20.210136
1970-01-01 00:07:23 power_api.c:68:check_voltage: target_vol = 20.20, actural_vol = 20.21, check voltage passed.
1970-01-01 00:07:32 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
1970-01-01 00:07:46 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
1970-01-01 00:07:52 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
1970-01-01 00:08:05 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
1970-01-01 00:08:12 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
1970-01-01 00:08:25 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
1970-01-01 00:08:31 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
1970-01-01 00:08:45 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
1970-01-01 00:08:53 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
1970-01-01 00:09:06 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
1970-01-01 00:09:13 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
1970-01-01 00:09:26 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
1970-01-01 00:09:33 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
1970-01-01 00:09:36 power_api.c:287:set_to_voltage_by_steps: Set to voltage raw 1900, step by step.
1970-01-01 00:09:46 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
1970-01-01 00:09:52 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
1970-01-01 00:09:54 power_api.c:87:check_voltage_multi: retry time: 0
1970-01-01 00:09:55 power_api.c:37:_get_avg_voltage: chain = 0, voltage = 18.981445
1970-01-01 00:09:56 power_api.c:37:_get_avg_voltage: chain = 1, voltage = 19.048799
1970-01-01 00:09:58 power_api.c:37:_get_avg_voltage: chain = 2, voltage = 18.987568
1970-01-01 00:09:58 power_api.c:50:_get_avg_voltage: average_voltage = 19.005937
1970-01-01 00:09:58 power_api.c:68:check_voltage: target_vol = 19.00, actural_vol = 19.01, check voltage passed.
1970-01-01 00:10:05 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
1970-01-01 00:10:14 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
1970-01-01 00:10:27 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
1970-01-01 00:10:31 frequency.c:761:inc_freq_with_fixed_step: chain = 1, freq_start = 555, freq_end = 585, freq_step = 5, is_higher_voltage = true
1970-01-01 00:10:31 power_api.c:287:set_to_voltage_by_steps: Set to voltage raw 1880, step by step.
1970-01-01 00:10:34 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
1970-01-01 00:10:47 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
1970-01-01 00:10:49 power_api.c:87:check_voltage_multi: retry time: 0
1970-01-01 00:10:50 power_api.c:37:_get_avg_voltage: chain = 0, voltage = 18.822246
1970-01-01 00:10:51 power_api.c:37:_get_avg_voltage: chain = 1, voltage = 18.858984
1970-01-01 00:10:52 power_api.c:37:_get_avg_voltage: chain = 2, voltage = 18.803877
1970-01-01 00:10:52 power_api.c:50:_get_avg_voltage: average_voltage = 18.828369
1970-01-01 00:10:52 power_api.c:68:check_voltage: target_vol = 18.80, actural_vol = 18.83, check voltage passed.
1970-01-01 00:10:53 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
1970-01-01 00:10:55 frequency.c:761:inc_freq_with_fixed_step: chain = 2, freq_start = 555, freq_end = 585, freq_step = 5, is_higher_voltage = true
1970-01-01 00:10:58 frequency.c:761:inc_freq_with_fixed_step: chain = 1, freq_start = 585, freq_end = 585, freq_step = 5, is_higher_voltage = true
1970-01-01 00:10:58 frequency.c:761:inc_freq_with_fixed_step: chain = 2, freq_start = 585, freq_end = 585, freq_step = 5, is_higher_voltage = true
1970-01-01 00:10:58 driver-btm-api.c:501:set_timeout: freq = 585, percent = 90, hcn = 73728, timeout = 126
1970-01-01 00:10:58 power_api.c:225:set_higher_voltage_raw: higher_voltage_raw = 1900
1970-01-01 00:10:58 power_api.c:281:set_to_higher_voltage_by_steps: Set to voltage raw 1900, step by step.
1970-01-01 00:11:06 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
1970-01-01 00:11:13 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
1970-01-01 00:11:16 power_api.c:87:check_voltage_multi: retry time: 0
1970-01-01 00:11:17 power_api.c:37:_get_avg_voltage: chain = 0, voltage = 18.975322
1970-01-01 00:11:18 power_api.c:37:_get_avg_voltage: chain = 1, voltage = 19.042676
1970-01-01 00:11:19 power_api.c:37:_get_avg_voltage: chain = 2, voltage = 18.993691
1970-01-01 00:11:19 power_api.c:50:_get_avg_voltage: average_voltage = 19.003896
1970-01-01 00:11:19 power_api.c:68:check_voltage: target_vol = 19.00, actural_vol = 19.00, check voltage passed.
1970-01-01 00:11:19 thread.c:709:create_check_system_status_thread: create thread
1970-01-01 00:11:20 driver-btm-api.c:1980:bitmain_soc_init: Init done!
1970-01-01 00:11:20 driver-btm-api.c:197:set_miner_status: STATUS_INIT
1970-01-01 00:11:25 driver-btm-api.c:197:set_miner_status: STATUS_OKAY
1970-01-01 00:11:26 frequency.c:196:get_ideal_hash_rate_GH: ideal_hash_rate = 55249
1970-01-01 00:11:26 frequency.c:212:get_sale_hash_rate_GH: sale_hash_rate = 53000
1970-01-01 00:11:26 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
1970-01-01 00:11:30 driver-btm-api.c:1172:dhash_chip_send_job: Version num 4
1970-01-01 00:11:35 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
1970-01-01 00:11:48 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
1970-01-01 00:11:54 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
1970-01-01 00:12:07 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
1970-01-01 00:12:14 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
1970-01-01 00:12:27 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
1970-01-01 00:12:34 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
1970-01-01 00:12:47 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
1970-01-01 00:12:55 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
1970-01-01 00:13:09 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
1970-01-01 00:13:15 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
1970-01-01 00:13:28 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
1970-01-01 00:13:35 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
1970-01-01 00:13:48 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
1970-01-01 00:13:54 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
1970-01-01 00:14:08 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
1970-01-01 00:14:16 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
1970-01-01 00:14:29 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
1970-01-01 00:14:36 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
1970-01-01 00:14:49 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
1970-01-01 00:14:56 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
1970-01-01 00:15:09 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
1970-01-01 00:15:15 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
1970-01-01 00:15:28 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
1970-01-01 00:15:37 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
1970-01-01 00:15:50 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
1970-01-01 00:15:57 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
1970-01-01 00:16:10 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
1970-01-01 00:16:16 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
1970-01-01 00:16:29 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
1970-01-01 00:16:36 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0
1970-01-01 00:16:49 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 1
1970-01-01 00:16:58 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 0
1970-01-01 00:17:11 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 0, chip = 55, reg = 1
1970-01-01 00:17:17 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 0
1970-01-01 00:17:30 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 1, chip = 40, reg = 1
1970-01-01 00:17:37 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 0
1970-01-01 00:17:50 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 2, chip = 180, reg = 1
1970-01-01 00:17:57 temperature.c:695:get_temp_info: read temp sensor failed: chain = 0, sensor = 3, chip = 195, reg = 0 |
|
|
|
|
Can anyone suggest anything to help here?
1. After around 20-30 mins of mining, I get a message of No data (in chinese) and it stops mining for about 10 minutes. Then starts up again and continues mining. Wondering whether it's a BT thing...
2. Of the 3 chains on the reporting page, the first one doesn't appear to have any hashing rate. The asic status is ok and all the other figures. The PCB temp is 51, the chip temp is 71 and the frequency is 555 compared to the other 2 at 585. The fans are all up around 6000rpm.
|
|
|
|
|
Thanks. I appreciate the help. To be clear.
1. I'm a newbie.
2. I was GIVEN the antminer.
3. I read the manual and dozens of posts/sites.
I'd actually put these details in previously but didn't know I had to wait 5-10 mins for it to kick in.
|
|
|
|
|
Does this sound correct now? I just put the below into the URL and nothing in Worker and Password?
cgminer -o stratum+tcp://solo.ckpool.org:3333 -u 1JuHMs8FZTzazq7B9B9Eg6oYpSQ9ADSTL9.0 -p x
Getting Socket connect failed: Connection refused error. Bloody thing.
|
|
|
|
Complete newbie here. I've been given an Antminer S17 and wanted to try it out. I think everything is connected up ok, but can you tell me if I've got this right to operate:
URL: stratum+tcp://de.ckpool.org:3333
Worker: xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx
Password: 123
nope . since I have no idea what you put for worker. a suggestion is put in a real btc addy and show us the BTC addy. we can show you if it is working. If you want privacy do it again with a real btc addy but do not tell us the one you use for keeps. here is an address I am mining to right now https://solo.ckpool.org:444/users/146UJM5kgzLVUV23CXCf33KQKHckoX1gx3note I disabled this https : // solo.ckpool . org: 444/ users / use your address to check not mine 146UJM5kgzLVUV23CXCf33KQKHckoX1gx3 Oh man, I'm such an idiot. BTC address, not wallet Thanks! Got it now. Seems to be working  I was looking at it all wrong. |
|
|
|
|
Complete newbie here. I've been given an Antminer S17 and wanted to try it out. I think everything is connected up ok, but can you tell me if I've got this right to operate:
URL: stratum+tcp://de.ckpool.org:3333
Worker: xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx
Password: 123
|
|
|
|
|
If everything is above board, I will buy it from you. DM me here to discuss payment & delivery.
|
|
|
|
Am selling for 1,300$
What is your WhatsApp or Viber number so i can add you and we chat about the miner because am not always online here.
You can add me or WhatsApp or viber (Mohammed +447438894079)
I await your soonest reply
Thanks
Are you still selling this? Looks like you're in the UK? |
|
|
|
|
Looking for Antminer S19 or S17. Ideally in the UK already if possible - makes things easier.
|
|
|
|
|
