 Show Posts
|
|
Pages: [1]
|
Super Zombie Mode requires lolminer and 4gb gpu. You can run 1 or 2 (a few very large cpus can run 3 or more) 4gb gpus at nearly full speed. You must put the card physically in the long slots. 1st gpu in slot 0 closest the cpu. The second if your board support into another full slot, The trick works by using the pcie lanes to supplement the vram on gpu with a little bit of system ram. You need x16 pcie lanes to get full speed with x8 providing about 50% of the SZM vs ZM. So a 570 about 26+mhs, 560 14.5mhs....at SZM.
So if you had say a 3 card riig (580-8 / 570-4 / 560-4)..and it has 2 long slots...and you have 24 pcie lanes becuase of the cpu you are running you would put 570-4 in slot 0 / 560-4 in slot 1 / 580-8 on riser to x1 slot...and could see 26/14/30mhs = 70mhs.
Which beats the hell out of doing all x1 risers and only seeing 48mhs for all 3 cards (4gb cards would be in zm but not szm)
It will end but looks to be some weeks/months away. Eventually the dag will grow to a point were there is no speed advantage to using system ram. The pcie lanes are not quite fast enough to equal the speed of vram...if it was it would continue to work. Its all about moving bits fast.
You dont have to set options in command line. It will detect and tune all cards automatically. Just set algo to eth.
Hey does this work on Windows ? Or MUST be in Linux? |
|
|
|
add -config config.txt: setx GPU_FORCE_64BIT_PTR 0 setx GPU_MAX_HEAP_SIZE 100 setx GPU_USE_SYNC_OBJECTS 1 setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_SINGLE_ALLOC_PERCENT 100 PhoenixMiner.exe -pool eth-us-east1.nanopool.org:9999 -wal WALLETNUMBER.RIGNAME -pass x -config config.txtpause and move following part to config.txt: -amd
-acm
-mode 1
-hstats 1
-cclock 1250
-mclock 2250
-cvddc 890
-mvddc 890
-log 0
-tstop 85
-tstart 55
-tt 65
#-fanmin 45
-fanmin 35,40,35,35,35,35,35
-fanmax 100
-cdm 0
-fcm 2
-gpus 1,2,3,4,5,6,7
-clKernel 1
-gser 5
-altinit
-rvram -1
-wdog 0
-rmode 0
You can also move -wallet -pass and -pool options to config.txt Edit: You should still customize this config for your GPUs (number and model) Do you think it would be possible to post screen shot of your miner file AND config file so I can see? (You can hide your wallet number and rig name if you want of course) Thanks in advance There is no secret in my config but I prefer not to post it here as it would just create more confusion for you, so forget the config above as well. Start from scratch, download PhoenixMiner, open start_miner.bat file with notepad and replace your wallet, then save and try to run it. Also read the readme.txt file in the same folder where you can find a lot other information. Before asking any other questions, remember to specify which GPU you are using. Good luck! Hello, Ive been mining without any trouble. I just seem to have trouble with 5.2d. I have MSI RX 580 8GB that is running well with another version of Phoenix Miner I also have 2 XFX RX 570 4GB and 1 MSI RX 570 4GB. Havent been able to run any of them due to them being 4GB. This is why I have decided to try 5.2d. My 4GB cards are currently NOT plugged in. So I only hvave my 8GB card. But it seems like I have been getting error with 5.2d. Can't even get it to work with my 8 GB Card.... |
|
|
|
add -config config.txt: setx GPU_FORCE_64BIT_PTR 0 setx GPU_MAX_HEAP_SIZE 100 setx GPU_USE_SYNC_OBJECTS 1 setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_SINGLE_ALLOC_PERCENT 100 PhoenixMiner.exe -pool eth-us-east1.nanopool.org:9999 -wal WALLETNUMBER.RIGNAME -pass x -config config.txtpause and move following part to config.txt: -amd
-acm
-mode 1
-hstats 1
-cclock 1250
-mclock 2250
-cvddc 890
-mvddc 890
-log 0
-tstop 85
-tstart 55
-tt 65
#-fanmin 45
-fanmin 35,40,35,35,35,35,35
-fanmax 100
-cdm 0
-fcm 2
-gpus 1,2,3,4,5,6,7
-clKernel 1
-gser 5
-altinit
-rvram -1
-wdog 0
-rmode 0
You can also move -wallet -pass and -pool options to config.txt Edit: You should still customize this config for your GPUs (number and model) Do you think it would be possible to post screen shot of your miner file AND config file so I can see? (You can hide your wallet number and rig name if you want of course) Thanks in advance |
|
|
|
Hi everyone
I am having issue with 5.2d
When I turn Phoenix Miner on, it says "Press any key to continue".
Once I press any key with my keyboard, the miner closes
Any idea?
Think is some error in config or bat file.. Any idea what? Would you mind sharing your config and bat file infos? (delete you wallet number and name if you want) Same version 5.2C and 5.2.D, cause concern with my RX580 8GB cards, I lose MH/S even with daglimit XXXX
I reverted to 5.1C is no longer a problem.
Can you tell us the driver version and what are you mining (ETH or ETC)? We can't detect any loss of hashrate on 8GB cards in our internal testing. - Driver AMD 19.5.2 - Mining ETH on ethermine.org - Cards rx580 nitro+ and rx580 nitro+ SE - vram 8Go -amd
-acm
-mode 1
-hstats 1
-cclock 1250
-mclock 2250
-cvddc 890
-mvddc 890
-log 0
-tstop 85
-tstart 55
-tt 65
#-fanmin 45
-fanmin 35
-fanmax 100
-cdm 0
-fcm 2
-gpus 1
-clKernel 1
-gser 5
-altinit
-rvram -1
-wdog 0
-rmode 0
Try my config !I should copy and paste this on my miner note pad? (bat file) Right under "pause"? yes add your pool and run it ! This is what I did and it's not working. Same error setx GPU_FORCE_64BIT_PTR 0 setx GPU_MAX_HEAP_SIZE 100 setx GPU_USE_SYNC_OBJECTS 1 setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_SINGLE_ALLOC_PERCENT 100 PhoenixMiner.exe -pool eth-us-east1.nanopool.org:9999 -wal WALLETNUMBER.RIGNAME -pass x pause -amd -acm -mode 1 -hstats 1 -cclock 1250 -mclock 2250 -cvddc 890 -mvddc 890 -log 0 -tstop 85 -tstart 55 -tt 65 #-fanmin 45 -fanmin 35,40,35,35,35,35,35 -fanmax 100 -cdm 0 -fcm 2 -gpus 1,2,3,4,5,6,7 -clKernel 1 -gser 5 -altinit -rvram -1 -wdog 0 -rmode 0 |
|
|
|
Hi everyone
I am having issue with 5.2d
When I turn Phoenix Miner on, it says "Press any key to continue".
Once I press any key with my keyboard, the miner closes
Any idea?
Think is some error in config or bat file.. Any idea what? Would you mind sharing your config and bat file infos? (delete you wallet number and name if you want) Same version 5.2C and 5.2.D, cause concern with my RX580 8GB cards, I lose MH/S even with daglimit XXXX
I reverted to 5.1C is no longer a problem.
Can you tell us the driver version and what are you mining (ETH or ETC)? We can't detect any loss of hashrate on 8GB cards in our internal testing. - Driver AMD 19.5.2 - Mining ETH on ethermine.org - Cards rx580 nitro+ and rx580 nitro+ SE - vram 8Go -amd
-acm
-mode 1
-hstats 1
-cclock 1250
-mclock 2250
-cvddc 890
-mvddc 890
-log 0
-tstop 85
-tstart 55
-tt 65
#-fanmin 45
-fanmin 35
-fanmax 100
-cdm 0
-fcm 2
-gpus 1
-clKernel 1
-gser 5
-altinit
-rvram -1
-wdog 0
-rmode 0
Try my config !I should copy and paste this on my miner note pad? (bat file) Right under "pause"? |
|
|
|
Hi everyone
I am having issue with 5.2d
When I turn Phoenix Miner on, it says "Press any key to continue".
Once I press any key with my keyboard, the miner closes
Any idea?
Think is some error in config or bat file.. Any idea what? Would you mind sharing your config and bat file infos? (delete you wallet number and name if you want) |
|
|
|
|
Hi everyone
I am having issue with 5.2d
When I turn Phoenix Miner on, it says "Press any key to continue".
Once I press any key with my keyboard, the miner closes
Any idea?
|
|
|
|
|
