 Show Posts
|
|
Pages: [1]
|
|
sp_,
I try with the last update of HiveOs, I think they failed the 1.22 upgrade and correct that yesterday.
Now -Y [id] work perfectly !
about the --lhr-unlock [id] command, the id number is only for the nvidia card, you agree ?
So if I have :
GPU0 : nvidia
GPU1 : nvidia LHR
GPU2 : amd
GPU3 : nvidia
The command should be : --lhr-unlock [0,1,0] with 0 (1st nvidia), 1 (2nd nvidia), 0 (3rd nvidia) ?
Does the unlock command work with FE version (3070ti and 3080ti) ?
Regards,
snoby
|
|
|
|
Maybe it is because it is an old HiveOs image file ? With new amd driver could work ? Amd drivers 20.40 (5.11.0701)
Use the latest HiveOs image file, and the latest nvidia driver. I already have the latest nvidia driver, but I’ll try tomorrow to put the lastest HiveOs image file on the rig and give you the Feedback if working or not. |
|
|
|
--list-devices give me 0 to 4 cuda device (Nvidia) and 5 to 7 CL devices (amd).
So i put -Y [4,5,6] -U [0,1,2,3]
Look in my picture. --list-devices give opencl Device number: 5 (amd card) so I use -Y [5] to enable the amd card. Does one card work? I try only with -Y [5] or 6 or 7 on my side, no other parameters (see on my picture, I have 3 AMD card). Again No device selected on my miner. With -b AMD card works fine. I try -Y [id] with id = 0 to 20, invalid CL for 0 to 4 and no devices for 5 to 20. Maybe it is because it is an old HiveOs image file ? With new amd driver could work ? Amd drivers 20.40 (5.11.0701) |
|
|
|
What about the bugged command --cl-devices or -Y? Do you have a deadline to find an issue ?
Like first rig amd gpu are gpu0-1 then on rig2 gpu0 is nvidia and when loading miner to get correct settings on first rig will give rig2 incorrect settings so it's difficult to used mixed rigs
This was fixed in v1.22. Working fine here... If you have a opencl and a cuda selection in the same launch config the Opencl devices will be selected first. In the picture I am running with --cu-devices[1] --cl-devices [5] gpu0: rx 580 AMD (cl-device #5) gpu1: gtx 2060 (cuda device #1)  -Y [5,6,7] : no device are set
Are you sure you are using the correct version? Hello sp_ Yes I use TBM 1.22 on HiveOs. --list-devices give me 0 to 4 cuda device (Nvidia) and 5 to 7 CL devices (amd). So i put -Y [4,5,6] -U [0,1,2,3] Nvidia start fine, and AMD not. Maybe you would like a log file or somerthing like that ? Another guy who use TBM try on his side and same issue |
|
|
|
|
What about the bugged command --cl-devices or -Y? Do you have a deadline to find an issue ?
|
|
|
|
thanks! this is very good news! I promote TBM among the Russian miners community. already have satisfied users.
Thanks for your support. v1.22 has been added to hiveos. Can you try v1.22?. Should work now.
I will try it when it will be added to HiveOS (: Added to hiveos now. Yep, I try with my bug on mixed rig... AMD cards still not work. My AMD devices are 5, 6 and 7 (see the picture hereafter)  -Y [5,6,7] : no device are set No problem on nvidia cards. Only -b is working, so the nvidia cards should stay on other miner :-( |
|
|
|
I have the same problem, asked SP_ 3-4 times and didn’t respond...
Choose Nvidia card ok no problem, choose only AMD card no problem, but choose couple of nvidia and all amd card impossible...
It's a bug in v1.21 in the --cl-device selection. I have reproduced and fix it in v1.22. So you need to wait for the new version. Thx for the feedback, good job and continu like that ! Have a nice day |
|
|
|
You pick the devices you want to mine with the command line options --cl-devices [6] --cu-devices [2]
to see the correct id use: tbminer --list-devices It doesn't work. I had to write --cuda-devices [2], cu is not recognized by TBM TBM doesn't mine with my AMD cards with those settings https://ibb.co/KrZsvTchttps://ibb.co/pbV9R4qhttps://ibb.co/PG4mhTpI have the same problem, asked SP_ 3-4 times and didn’t respond... Choose Nvidia card ok no problem, choose only AMD card no problem, but choose couple of nvidia and all amd card impossible... |
|
|
|
|
sp_, do you have an idea about my problem ? Message #1096
Still do not work to chose nvidia and amd card one by one
|
|
|
|
Do tou have an idea with mine ?  |
|
|
|
I try, but seems the same problem try cl-devices before cuda-devices --cl-devices [1] --cuda-devices [2] I will give you all my config rig. With -D I have : If I only try --cl-devices [5] I have : No device are set It is the same for --cl-devices [6] and [7].  Maybe it is the begining of my problem. |
|
|
|
I try to setup TBM on HiveOs with different GPU.
I try all --cl-devices [ i ] with i=0 to 15 and all the time the miner fail and restart.
You can try the short option instead -Y [ 0 ] I try, but seems the same problem |
|
|
|
|
Hello All,
I try to setup TBM on HiveOs with different GPU.
GPU 0 : 3070ti
GPU 1 : 6700XT
GPU2 : 3060ti
etc
I try different setting to take only 3060ti and 6700XT but seems doesn't work.
AMD driver : 20.40 (5.11.0701)
Nvidia driver : 495.44
1st test : -b --> take only amd card is working
2nd test : --auto-detect --> all card is working
3rd test : --cuda-devices [2] --> OK only 3060ti is working
4rd test : --cuda-devices [2] --cl-devices [1] --> 1 is the id of the 6700XT card // FAIL : source/sp_workers/cl_gpu.cpp:cl_setup_devices():576: A OpenCL runtime error occured: CL_INVALID_VALUE
I try all --cl-devices [ i ] with i=0 to 15 and all the time the miner fail and restart.
I just would like to take all the AMD card and a list of NVIDIA card (no-LHR card), do you have another way to do that or something I do wrong ?
|
|
|
|
|
