Show Posts
I received recently from bitmain reseller my 6 S19 JPro 104 Th i ordered a couple of weeks ago ! I started the configuration on the servers one by one and plugged them on my farm gradually ! one of them started to show abnormal behaviour until i noticed that the hashbords went off- line after some server reboots !!
Kindly get notified that the server is still under warranty period
Other 5 Servers S19 JPro are mining fine !! Except the one mentioned above
please find in the attachment the log file for the faulty server
2023-05-14 12:34:52 ==========================capability start==========================
2023-05-14 12:34:52 board num = 3
2023-05-14 12:34:52 board id = 0, chain num = 1
2023-05-14 12:34:52 chain id = 0
2023-05-14 12:34:52 board id = 1, chain num = 1
2023-05-14 12:34:52 chain id = 1
2023-05-14 12:34:52 board id = 2, chain num = 1
2023-05-14 12:34:52 chain id = 2
2023-05-14 12:34:52 ==========================capability end============================
2023-05-14 12:34:52 chain num = 3
2023-05-14 12:34:52 skip loading levels for now
2023-05-14 12:34:53 load chain 0 eeprom data
2023-05-14 12:34:54 load chain 1 eeprom data
2023-05-14 12:34:54 load chain 2 eeprom data
2023-05-14 12:34:54 i2c_sim_init start
2023-05-14 12:34:54 init gpio477
2023-05-14 12:34:54 init gpio476
2023-05-14 12:34:54 i2c_sim_init end
2023-05-14 12:34:56 power open power_version = 0x75
2023-05-14 12:34:58 power is not Calibrated
2023-05-14 12:35:00 miner type: Antminer S19j Pro
2023-05-14 12:35:00 multi machine mode
2023-05-14 12:35:00 load machine BHB42603 conf
2023-05-14 12:35:00 machine : BHB42603
2023-05-14 12:35:00 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2023-05-14 12:35:00 fan_eft : 0 fan_pwm : 100
2023-05-14 12:35:00 create thread get_nonce_and_register_thread
2023-05-14 12:35:00 fixed working voltage = 1360
2023-05-14 12:35:00 min freq in eeprom = 545
2023-05-14 12:35:00 fixed frequency is 545
2023-05-14 12:35:00 Chain
- PCB Version: 0x0170
- BOM Version: 0x0010
2023-05-14 12:35:00 Chain [1] BOM Version: 0x0010
2023-05-14 12:35:00 Chain [2] PCB Version: 0x0170
2023-05-14 12:35:00 Chain [2] BOM Version: 0x0010
2023-05-14 12:35:00 bad chain id = 3
2023-05-14 12:35:00 Fan check passed.
2023-05-14 12:35:00 uart_trans addr:0xf704d000.
2023-05-14 12:35:00 max sensor num = 4
2023-05-14 12:35:00 STATUS_INITED: soc init done!
2023-05-14 12:35:00 temperature_monitor_thread start...
2023-05-14 12:35:02 start to init...
2023-05-14 12:35:04 power type version: 0x0075
2023-05-14 12:35:05 disable power watchdog: 0x0000
2023-05-14 12:35:06 Enter sleep to make sure power release finish.
2023-05-14 12:36:02 Slept 55 seconds, diff = 5.
2023-05-14 12:36:06 set_voltage_by_steps to 1500.
2023-05-14 12:36:15 start up min temp by 75a = 24
2023-05-14 12:36:18 Chain[0]: find 126 asic, times 0
2023-05-14 12:36:19 !!! reg crc error
2023-05-14 12:36:20 Chain[1]: find 124 asic, times 0
2023-05-14 12:36:21 !!! reg crc error
2023-05-14 12:36:22 Chain[1]: find 124 asic, times 1
2023-05-14 12:36:23 !!! reg crc error
2023-05-14 12:36:24 Chain[1]: find 124 asic, times 2
2023-05-14 12:36:24 Chain 1 only find 124 asic, will power off hash board 1
2023-05-14 12:36:26 Chain[2]: find 126 asic, times 0
2023-05-14 12:36:26 ERROR_SOC_INIT: soc init failed!
2023-05-14 12:36:26 stop_mining: soc init failed!
2023-05-14 12:36:26 uninit_temp_info
2023-05-14 12:36:26 do not read temp anymore...
2023-05-14 12:36:26 cancel thread
2023-05-14 12:36:26 ****power off hashboard****
2023-05-14 12:36:27 temp monitor thread exit
2023-05-14 12:37:19 Version num 65536
2023-05-14 12:37:19 Mask num 0x1fffe000
2023-05-14 12:37:19 opt_multi_version = 65536, interval timeout = 2837042
2023-05-14 12:37:19 freq = 545, percent = 90, hcn = 4809, timeout = 2837042
Would you please assist for the case described !
Many Thanks in advance.
