Anyone here have the dimensions for the bus bar? Trying to make one on autocad but I don't have the specific dimensions atm to cut it out. Just need the length and width. Third pic from the top.

https://bixbit.io/en/documentation/connecting-an-additional-variable-power-supply-unit/3-setting-and-connecting-an-additional-power-supply-unit

Chips say they reach 30 C on the miner's IP website. Seems like a possible error in the firmware to me, considering the voltage does not show up correctly when using 2 PSUs.
Is there another way to connect the PSU apart from commoning the ground?

The surface temp for the machine never got hotter than 50-55C as the firmware would stop it from doing so. I can run at 93TH forever without the power supply. When I connect the supply, it runs for about 10-20 minutes at a comfortable 100 TH before stopping, and then it only goes up to 50 TH after that.

I have a whatsminer MS30. I scrapped a Core Scientific DL SeKU-2R5S12 power supply with an input of 100-240VAC 50/60Hz 15A max and an output of 13.2Vdc/184A @230Vac 13.2 Vdc/116A@120Vac. I made a new board out of aluminum with the leftmost connection between the board and the power supply cut off (the one that looks like an L) and connected that one to my power supply, as detailed here:
https://bixbit.io/en/documentation/connecting-an-additional-power-supply-unit/2-the-connection-procedure-of-the-additional-power-supply-unit .
On startup, I am able to get it to about 100 TH until  it seems to overheat and I get error code 5050. The new PSU is connected to only one hashboard.

Anyone here know the procedure on what frequency and voltage to set whatsminers at using bixbit when overclocking with 2 PSUs? I'm having errors connecting a PSU currently and I am pretty sure it has to do with how the machine's settings are configured.

I'm trying to overclock some whatsminers right now with 2 PSUs. Usually it works fine, pulling power like it should, until after about 20 minutes I get an error of 505x or 901 depending on how high I have my power consumption settings. Anyone here have any experience dealing with these errors? I don't know where to start troubleshooting, but I have a feeling it has to do with the finer points of tuning the firmware's frequency and other power related specs.

Is there any documentation in general of non-stock whatsminer PSUs being used to overclock the miners?

I have some extras laying around and wanted to use them as scrap. Where I live PSUs are expensive, but scrapped Canaan ones are not. If I go to the scrapyard, is there any guide to know which PSUs in general will work?

Thank you for the reply. What does the testing procedure look like? Any guide or resource that exists online?

Does anyone know if it is possible to overclock a whatsminer ms30 with an avalon PSU? I've seen people do it with stock PSUs but I haven't gotten mine to work with an old Avalon PSU. I'm not sure if this is due to the fact that the Avalon PSU might be programmable - not sure if that PSU is or isn't. Anyone here have any experience with this? I was curious if it would even be possible with the s19 power supplies, or if those need to be reprogrammed in some way to function as a normal power supply. I'm lacking the proper documentation to know - if anyone has any experience with the topic or could point me in the right direction I would appreciate it.

I'm looking into making my own automated bitcoin trader and Gekko seemed like a good option, but I'm worried about it not being maintained anymore. Anyone here have any experience with it? I want to make sure as of this year it's still a viable option. If anyone has any other recommendations, I'd love to hear them. I have a friend that also is looking for software with automated payments that isn't on binance and I haven't been able to easily find a wallet with those kind of uses. If anyone can point me in their direction, it would be greatly appreciated.