Latest posts of: Mtplig

Quote from: BitMaxz on September 19, 2023, 05:45:27 PM

Quote from: Mtplig on September 19, 2023, 05:23:44 PM

How can I get the logs?

I don't know exactly how but if you can access the IP would you mind adding this after you type the IP on the browser "/logs" without the double quote.

Sample 192.168.90.4/logs
Then post here with the insert code tag.

I installed the innomonitor and managed to find error code 35

Quote from: BitMaxz on September 18, 2023, 10:57:04 PM

Quote from: Mtplig on September 18, 2023, 07:23:10 PM

Yes. I managed to install the soc version. But it’s still not mining. It stays at the status page and never shows the hashrate, fan speed etc. I have left it running for about 2 hours now and does not appear on the pool also. What can I do more?

Would you mind to tell us where or what pool you mine you might be configuring the pool incorrectly extra spaces can cause to miner not to work properly.

If its setup fine then can you share the logs here so that we can analyze the issue

How can I get the logs?

Quote from: BitMaxz on September 18, 2023, 10:57:04 PM

Quote from: Mtplig on September 18, 2023, 07:23:10 PM

Ok thanks for the help!
When I set to factory settings it goes to the factory pool but that way it also does not hash. Later I will turn it on again and send the log

Quote from: BitMaxz on September 18, 2023, 12:38:16 PM

Quote from: Mtplig on September 18, 2023, 11:43:51 AM

I tried to upgrade the firmware and it says on status: Failure
I tried upgrading on the miner web page

Check carefully the firmware you are trying to flash t2th+ does have two different firmware the Soc and G19 firmware.

Check the miner's dashboard under overview you should see the controller's version if it's g19 or Soc. Or check the control board directly there is a G19 or Soc version written on the control board.

Quote from: Mtplig on September 18, 2023, 07:42:23 AM

Quote from: ZeusBtc.com on September 18, 2023, 01:32:21 AM

Hey, you can download with confidence at ZeusBtc.com, these firmwares are from Innosilicon.
Innosilicon Miner Firmware Download | Zeus Mining

Ok thanks. I am going to try this out. Still have not recieved response from innosilicon

Hello.
I tried to upgrade the firmware and it says on status: Failure
I tried upgrading on the miner web page

Quote from: ZeusBtc.com on September 18, 2023, 01:32:21 AM

Hey, you can download with confidence at ZeusBtc.com, these firmwares are from Innosilicon.
Innosilicon Miner Firmware Download | Zeus Mining

Ok thanks. I am going to try this out. Still have not recieved response from innosilicon

Quote from: BitMaxz on September 17, 2023, 08:24:54 AM

Quote from: Mtplig on September 17, 2023, 07:48:57 AM

Ok thanks. I did check on their website but there are no updates. I sent an email to them. I did find some firmware on the web but it’s risky stuff

Where did you find the firmware? Did you find them on the Innosilicon website?
If you find a firmware make sure the firmware is for t2th+ but if it's a random firmware don't use it because flashing a random firmware to this unit can brick a program and unable to flash it back to stock firmware be careful.

No I found external of innosilicon website. So it can contain malicious virus

Ok thanks. I did check on their website but there are no updates. I sent an email to them. I did find some firmware on the web but it’s risky stuff

Hello!
I have a innosilicon t2th+ that is not hashing. I set the pool and worker and it only says updating settings. I leave it on for about 2hours and it does not go past through that setting. It also does not appear on the pool. I have tried resetting it with no improvement. Anyone knows what is wrong?

It was infected with a virus. I updated the firmware and changed the ip and password. Now it’s all ok. What I notice now is that the hashrate has gone from 81th to 76th. I have done the aging option but it does not pass from that

Quote from: BitMaxz on September 07, 2023, 04:29:47 PM

Did you buy this miner as a used unit?

Can you use other devices to set up your miner maybe the device you currently using is infected try to set up your miner through mobile or another PC that you know is clean.

Also, try to change the pool using another browser and incognito mode.
Update here if it works or not.

Yes I bought it used but it was working fine.
What is strange is that it changes the login password. Usually it should be root

Quote from: DaveF on September 07, 2023, 01:32:58 PM

Quote from: Mtplig on September 07, 2023, 12:41:18 PM

It changes to a pool I think is original. Pool: stratum+tcp://sd.antpool.com:3333 with worker name: stockmnr.avalon

ss.antpool or sd.antpool? sd is not a valid address.

stockmnr.avalon is not what mine defaults to, but I don't know if they have more then 1 username.

I would make sure you are on the latest firmware https://www.canaan.io/service/447
and reach out to avalon support they also have a sales rep in the forum you can try sending a PM to: https://bitcointalk.org/index.php?action=profile;u=3481962

-Dave

Thanks for the help. It is ss.antpool and the worker is stockmnr.avalon. How can I check the if I am on the latest firmware?

It changes to a pool I think is original. Pool: stratum+tcp://sd.antpool.com:3333 with worker name: stockmnr.avalon

Hello,
I have some Avalon 1166pro but 1 asic is always rebooting and changing the pool address and worker name.
It also changes the login password. Usually it is user: root and pass: root but it changes the password to another.
Has someone had similar problem?