Hi could some body take a look at this please. I just purchaced from some body and got faults. can you tell when the fault first happened
Many thanks
0.000000@0] Booting Linux on physical CPU 0x0
[ 0.000000@0] Linux version 4.9.113 (jenkins@nomd-nomd-fwc-bj) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Fri Feb 2 17:23:53 CST 2024
[ 0.000000@0] Boot CPU: AArch64 Processor [410fd034]
[ 0.000000@0] earlycon: aml_uart0 at MMIO 0x00000000ff803000 (options '')
[ 0.000000@0] bootconsole [aml_uart0] enabled
[ 0.000000@0] efi: Getting EFI parameters from FDT:
[ 0.000000@0] efi: UEFI not found.
[ 0.000000@0] 07400000 - 07500000, 1024 KB, ramoops@0x07400000
[ 0.000000@0] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB
[ 0.000000@0] 05000000 - 05400000, 4096 KB, linux,secmon
[ 0.000000@0] cma: Reserved 16 MiB at 0x000000000f000000
[ 0.000000@0] On node 0 totalpages: 65536
[ 0.000000@0] DMA zone: 1024 pages used for memmap
[ 0.000000@0] DMA zone: 0 pages reserved
[ 0.000000@0] DMA zone: 65536 pages, LIFO batch:15
[ 0.000000@0] psci: probing for conduit method from DT.
[ 0.000000@0] psci: PSCIv1.0 detected in firmware.
[ 0.000000@0] psci: Using standard PSCI v0.2 function IDs
[ 0.000000@0] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000@0] psci: SMC Calling Convention v1.1
[ 0.000000@0] percpu: Embedded 25 pages/cpu @ffffffc00ef53000 s64536 r8192 d29672 u102400
[ 0.000000@0] pcpu-alloc: s64536 r8192 d29672 u102400 alloc=25*4096
[ 0.000000@0] pcpu-alloc:
[ 0.000000@0] Detected VIPT I-cache on CPU0
[ 0.000000@0] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64512
[ 0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=,loaded,androidboot.selinux=enforcing androidboot.firstboot=1 jtag=disable androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01 androidboot.build.expect.baseband=N/A androidboot.serialno=1234567890 androidboot.rpmb_state=0 rootfstype=ramfs init=/sbin/init
[ 0.000000@0] PID hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.000000@0] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.000000@0] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.000000@0] Memory: 209416K/262144K available (8764K kernel code, 1194K rwdata, 2424K rodata, 3648K init, 1017K bss, 32248K reserved, 20480K cma-reserved)
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ 0.000000@0] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)
[ 0.000000@0] .text : 0xffffff8009080000 - 0xffffff8009910000 ( 8768 KB)
[ 0.000000@0] .rodata : 0xffffff8009910000 - 0xffffff8009b80000 ( 2496 KB)
[ 0.000000@0] .init : 0xffffff8009b80000 - 0xffffff8009f10000 ( 3648 KB)
[ 0.000000@0] .data : 0xffffff8009f10000 - 0xffffff800a03aa00 ( 1195 KB)
[ 0.000000@0] .bss : 0xffffff800a03aa00 - 0xffffff800a139034 ( 1018 KB)
[ 0.000000@0] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 4116 KB)
[ 0.000000@0] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)
[ 0.000000@0] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)
[ 0.000000@0] 0xffffffbf00000000 - 0xffffffbf00400000 ( 4 MB actual)
[ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc010000000 ( 256 MB)
[ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] Build-time adjustment of leaf fanout to 64.
[ 0.000000@0] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
[ 0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[ 0.000000@0] axg_aoclkc_init: register ao clk ok!
[ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[ 0.000000@0] axg_amlogic_init_media: register meson media clk
[ 0.000000@0] axg_amlogic_init_misc: register amlogic axg misc clks
[ 0.000000@0] axg_amlogic_init_misc: register amlogic sdemmc clk
[ 0.000000@0] axg_clkc_init initialization complete
[ 0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000003@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.008251@0] meson_bc_timer: mclk->mux_reg =ffffff800800a190,mclk->reg =ffffff800800c194
[ 0.016908@0] Console: colour dummy device 80x25
[ 0.021106@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.031585@0] pid_max: default: 32768 minimum: 301
[ 0.036435@0] thread_stack_cache_init, vmap:ffffffc00e5af600, bitmap:ffffffc00e5a3000, cache page:e5e0
[ 0.045772@0] thread_stack_cache_init, allocation vm area:ffffffc00e5d94c0, addr:ffffff8020000000, size:20001000
[ 0.056004@0] cpu 0, vmap_stack:[ffffffc00ef5c960-ffffffc00ef60950]
[ 0.062303@0] cpu 0, irq_stack: [ffffffc00ef53060-ffffffc00ef57050]
[ 0.068603@0] cpu 1, vmap_stack:[ffffffc00ef75960-ffffffc00ef79950]
[ 0.074903@0] cpu 1, irq_stack: [ffffffc00ef6c060-ffffffc00ef70050]
[ 0.081203@0] cpu 2, vmap_stack:[ffffffc00ef8e960-ffffffc00ef92950]
[ 0.087503@0] cpu 2, irq_stack: [ffffffc00ef85060-ffffffc00ef89050]
[ 0.093803@0] cpu 3, vmap_stack:[ffffffc00efa7960-ffffffc00efab950]
[ 0.100103@0] cpu 3, irq_stack: [ffffffc00ef9e060-ffffffc00efa2050]
[ 0.106463@0] Security Framework initialized
[ 0.110696@0] SELinux: Initializing.
[ 0.114387@0] SELinux: Starting in permissive mode
[ 0.114424@0] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
[ 0.121107@0] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)
[ 0.128836@0] ftrace: allocating 30061 entries in 118 pages
[ 0.186603@0] sched-energy: CPU device node has no sched-energy-costs
[ 0.187417@0] CPU0: update cpu_capacity 1024
[ 0.191744@0] ASID allocator initialised with 32768 entries
[ 0.229879@0] secmon: can't fine clear_range
[ 0.230082@0] EFI services will not be available.
[ 0.233346@0] Meson chip version = RevC (25:C - 23:0)
[ 0.267017@1] Detected VIPT I-cache on CPU1
[ 0.267077@1] CPU1: update cpu_capacity 1024
[ 0.267079@1] CPU1: Booted secondary processor [410fd034]
[ 0.295086@2] Detected VIPT I-cache on CPU2
[ 0.295138@2] CPU2: update cpu_capacity 1024
[ 0.295141@2] CPU2: Booted secondary processor [410fd034]
[ 0.323141@3] Detected VIPT I-cache on CPU3
[ 0.323192@3] CPU3: update cpu_capacity 1024
[ 0.323194@3] CPU3: Booted secondary processor [410fd034]
[ 0.323283@0] Brought up 4 CPUs
[ 0.362503@0] SMP: Total of 4 processors activated.
[ 0.367412@0] CPU features: detected feature: 32-bit EL0 Support
[ 0.373448@0] CPU features: detected feature: Kernel page table isolation (KPTI)
[ 0.384002@0] CPU: All CPU(s) started at EL2
[ 0.385188@0] alternatives: patching kernel code
[ 0.390496@1] addr:ffffff802007be10 is in kernel, size fix 4096->10, data:mode=0755
[ 0.397716@0] devtmpfs: initialized
[ 0.412752@0] DMI not present or invalid.
[ 0.413150@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.421116@0] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.427694@0] pinctrl core: initialized pinctrl subsystem
[ 0.434088@0] NET: Registered protocol family 16
[ 0.457644@0] cpuidle: using governor menu
[ 0.458150@0] vdso: 2 pages (1 code @ ffffff8009917000, 1 data @ ffffff8009f14000)
[ 0.463751@0] hw-breakpoint: found 6 breakpoint and 2 watchpoint registers.
[ 0.471154@0] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.477321@0] clkmsr: clkmsr: driver init
[ 0.481350@0] aml_watch_point_probe, in, wp:2
[ 0.486776@0] pstore: using zlib compression
[ 0.490190@0] console [pstore-1] enabled
[ 0.493631@0] pstore: Registered ramoops as persistent store backend
[ 0.500039@0] ramoops: attached 0x100000@0x7400000, ecc: 0/0
[ 0.514390@0] aml_iomap: amlogic iomap probe done
[ 0.521184@0] clkmsr: msr_clk_reg0=ffffff800817e004,msr_clk_reg2=ffffff80081d100c
[ 0.523119@0] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0
[ 0.631370@0] usbcore: registered new interface driver usbfs
[ 0.631521@0] usbcore: registered new interface driver hub
[ 0.637152@0] usbcore: registered new device driver usb
[ 0.642461@0] pps_core: LinuxPPS API ver. 1 registered
[ 0.647385@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <
giometti@linux.it>
[ 0.656768@0] PTP clock support registered
[ 0.661105@0] dmi: Firmware registration failed.
[ 0.666103@0] secmon: reserve_mem_size:0x300000
[ 0.670132@0] secmon secmon: assigned reserved memory node linux,secmon
[ 0.677010@0] secmon: get page:ffffffbf00140000, 5000
[ 0.681746@0] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000
[ 0.690135@0] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000
[ 0.698009@0] NetLabel: Initializing
[ 0.700185@0] NetLabel: domain hash size = 128
[ 0.704772@0] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.710003@0] NetLabel: unlabeled traffic allowed by default
[ 0.716641@0] clocksource: Switched to clocksource arch_sys_counter
[ 0.843406@0] VFS: Disk quotas dquot_6.6.0
[ 0.843554@0] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.869660@0] NET: Registered protocol family 2
[ 0.870688@0] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.875902@0] TCP bind hash table entries: 2048 (order: 3, 32768 bytes)
[ 0.882631@0] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.889157@0] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.895121@0] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.901851@0] NET: Registered protocol family 1
[ 0.906834@0] RPC: Registered named UNIX socket transport module.
[ 0.912256@0] RPC: Registered udp transport module.
[ 0.917133@0] RPC: Registered tcp transport module.
[ 0.922030@0] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.931147@0] Unpacking initramfs...
[ 1.545473@2] Initramfs unpacking failed: junk in compressed archive
[ 1.554357@2] Freeing initrd memory: 8848K
[ 1.555285@2] hw perfevents: clusterb_enabled = 0
[ 1.557611@2] hw perfevents: cpumasks 0xf, 0x0
[ 1.562066@2] hw perfevents: cluster A irq = 7
[ 1.566632@2] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 1.576801@2] audit: initializing netlink subsys (disabled)
[ 1.580142@2] audit: type=2000 audit(1.392:1): initialized
[ 1.587447@2] workingset: timestamp_bits=62 max_order=16 bucket_order=0
[ 1.611499@2] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.618526@2] NFS: Registering the id_resolver key type
[ 1.618608@2] Key type id_resolver registered
[ 1.622537@2] Key type id_legacy registered
[ 1.627167@2] fuse init (API version 7.26)
[ 1.632504@2] SELinux: Registering netfilter hooks
[ 1.638718@2] NET: Registered protocol family 38
[ 1.638778@2] Key type asymmetric registered
[ 1.642022@2] Asymmetric key parser 'x509' registered
[ 1.647500@2] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 1.654714@2] io scheduler noop registered (default)
[ 1.659691@2] io scheduler deadline registered
[ 1.664575@2] io scheduler cfq registered
[ 1.685003@3] random: fast init done
[ 1.685102@3] random: crng init done
[ 1.685568@2] Unable to detect cache hierarchy for CPU 0
[ 1.725812@2] loop: module loaded
[ 1.731340@2] zram: Added device: zram0
[ 1.731737@2] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.736599@2] libphy: Fixed MDIO Bus: probed
[ 1.741828@2] tun: Universal TUN/TAP device driver, 1.6
[ 1.745769@2] tun: (C) 1999-2004 Max Krasnyansky <
maxk@qualcomm.com>
[ 1.753983@2] ee eth reset:Addr = ffffff80081fd008
[ 1.761466@2] meson6-dwmac ff3f0000.ethernet: no reset control found
[ 1.763409@2] stmmac - user ID: 0x11, Synopsys ID: 0x37
[ 1.768681@2] Ring mode enabled
[ 1.771889@2] DMA HW capability register supported
[ 1.776647@2] Normal descriptors
[ 1.779937@2] RX Checksum Offload Engine supported
[ 1.784855@2] COE Type 2
[ 1.787462@2] TX Checksum insertion supported
[ 1.791948@2] Wake-Up On Lan supported
[ 1.795883@2] Enable RX Mitigation via HW Watchdog Timer
[ 1.809438@2] libphy: stmmac: probed
[ 1.809491@2] eth%d: PHY ID 0007c0f1 at 0 IRQ POLL (stmmac-0:00) active
[ 1.815898@2] PPP generic driver version 2.4.2
[ 1.818903@2] PPP BSD Compression module registered
[ 1.823422@2] PPP Deflate Compression module registered
[ 1.828671@2] PPP MPPE Compression module registered
[ 1.833638@2] NET: Registered protocol family 24
[ 1.839104@2] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.845044@2] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.852093@2] usbcore: registered new interface driver cdc_acm
[ 1.857292@2] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.865696@2] usbcore: registered new interface driver usbserial
[ 1.872386@2] mousedev: PS/2 mouse device common for all mice
[ 1.877805@2] usbcore: registered new interface driver xpad
[ 1.883246@2] i2c /dev entries driver
[ 1.887963@2] cpu cpu0: bL_cpufreq_init: CPU 0 initialized
[ 1.892256@2] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi
[ 1.903162@2] ff803000.serial: clock gate not found
[ 1.904793@2] meson_uart ff803000.serial: ==uart0 reg addr = ffffff800830d000
[ 1.911957@2] ff803000.serial: ttyS0 at MMIO 0xff803000 (irq = 13, base_baud = 1500000) is a meson_uart
[ 1.926898@2] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 115200
[ 1.929608@2] console [ttyS0] enabled
[ 1.936826@2] bootconsole [aml_uart0] disabled
[ 1.946491@1] ff804000.serial: clock gate not found
[ 1.950619@1] meson_uart ff804000.serial: ==uart3 reg addr = ffffff8008321000
[ 1.957731@1] ff804000.serial: ttyS3 at MMIO 0xff804000 (irq = 14, base_baud = 1500000) is a meson_uart
[ 1.968080@0] meson_uart ffd24000.serial: ==uart1 reg addr = ffffff8008323000
[ 1.974224@0] ffd24000.serial: ttyS1 at MMIO 0xffd24000 (irq = 25, base_baud = 1500000) is a meson_uart
[ 1.984383@2] meson_uart ffd23000.serial: ==uart2 reg addr = ffffff8008325000
[ 1.990685@2] ffd23000.serial: ttyS2 at MMIO 0xffd23000 (irq = 26, base_baud = 1500000) is a meson_uart
[ 2.001684@1] amlogic-new-usb2 ffe09000.usb2phy: USB2 phy probe:phy_mem:0xffe09000, iomap phy_base:0xffffff8008348000
[ 2.010932@1] amlogic-new-usb3 ffe09080.usb3phy: This phy has no usb port
[ 2.017443@1] amlogic-new-usb3 ffe09080.usb3phy: USB3 phy probe:phy_mem:0xffe09080, iomap phy_base:0xffffff800834c080
[ 2.032429@1] i2c i2c-1: of_i2c: modalias failure on /soc/aobus@ff800000/i2c@5000/mcu6350@40
[ 2.036253@1] i2c i2c-1: Failed to create I2C device for /soc/aobus@ff800000/i2c@5000/mcu6350@40
[ 2.048567@1] aml_dma ff63e000.aml_dma: Aml dma
[ 2.051751@1] aml_aes_dma ff63e000.aml_dma:aml_aes: Aml AES_dma
[ 2.056793@1] aml_sha_dma ff63e000.aml_dma:aml_sha: Aml SHA1/SHA224/SHA256 dma
[ 2.063140@1] efusekeynum: 4
[ 2.065496@1] efusekeyname: mac offset: 0 size: 6
[ 2.071882@1] efusekeyname: mac_bt offset: 6 size: 6
[ 2.078294@1] efusekeyname: mac_wifi offset: 12 size: 6
[ 2.084701@1] efusekeyname: usid offset: 18 size: 16
[ 2.091526@3] efuse efuse: probe OK!
[ 2.097040@3] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller
[ 2.104377@3] meson-mmc: >>>>>>>>hostbase ffffff8008358000, dmode
[ 2.109313@3] meson-mmc: actual_clock :400000, HHI_nand: 0x80
[ 2.114507@3] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000033c
[ 2.160767@3] meson-mmc: meson_mmc_probe() : success!
[ 2.161029@3] amlogic mtd driver init
[ 2.165082@3] prase_get_dtb_nand_parameter:128,parse dts start
[ 2.169842@3] bl mode descrete
[ 2.172720@3] fip_copies 4
[ 2.175385@3] fip_size 0x200000
[ 2.178524@3] nand_clk_ctrl 0xffe07000
[ 2.182248@3] prase_get_dtb_nand_parameter:234,parse dts end
[ 2.187917@3] nand_clk_ctrl 0xffe07000
[ 2.191637@3] nand register base ffffff80083df800, nand clock register ffffff80083e1000
[ 2.200373@3] plat->aml_nand_device ffffff800a005c10
[ 2.204560@3] m3_nand_probe() aml_nand_device ffffff800a005c10
[ 2.210607@3] NAND device id: 2c da 90 95 6 0
[ 2.214671@3] NAND device: Manufacturer ID:
[ 2.218737@3] 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
[ 2.225780@3] oob_fill_cnt =32 oob_size =64, bch_bytes =14
[ 2.231215@3] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
[ 2.236762@3] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
[ 2.243008@3] mtd->oobavail: 0x8
[ 2.246475@3] aml_nand_init 2119: plat-name:bootloader
[ 2.251327@3] Creating 1 MTD partitions on "bootloader":
[ 2.256615@3] 0x000000000000-0x000000200000 : "bootloader"
[ 2.265455@1] bootloader initialized ok
[ 2.265874@1] plat->aml_nand_device ffffff800a005c10
[ 2.270863@1] m3_nand_probe() aml_nand_device ffffff800a005c10
[ 2.276989@1] NAND device id: 2c da 90 95 6 0
[ 2.280994@1] NAND device: Manufacturer ID:
[ 2.285041@1] 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
[ 2.292084@1] oob_fill_cnt =32 oob_size =64, bch_bytes =14
[ 2.297516@1] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
[ 2.303067@1] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
[ 2.309310@1] mtd->oobavail: 0x8
[ 2.312733@1] aml_nand_init 2119: plat-name:nandnormal
[ 2.317675@1] bbt_start=20
[ 2.320289@1] env_start=24
[ 2.323006@1] key_start=32
[ 2.325682@1] dtb_start=40
[ 2.328348@1] ddr_start=44
[ 2.331056@1] nbbt: info size=0x800 max_scan_blk=24, start_blk=20
[ 2.337548@1] get_free_node 43: bitmap=0
[ 2.341023@1] get_free_node 55: bitmap=1
[ 2.345114@1] get_free_node 43: bitmap=1
[ 2.348821@1] get_free_node 55: bitmap=3
[ 2.352913@1] get_free_node 43: bitmap=3
[ 2.356603@1] get_free_node 55: bitmap=7
[ 2.360523@1] nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1
[ 2.367193@1] nbbt free list:
[ 2.370140@1] blockN=21, ec=-1, dirty_flag=0
[ 2.374386@1] blockN=22, ec=-1, dirty_flag=0
[ 2.378632@1] blockN=23, ec=-1, dirty_flag=0
[ 2.382881@1] aml_nand_scan_rsv_info 1141: page_num=1
[ 2.388289@1] nbbt valid addr: 280000
[ 2.391547@1] aml_nand_bbt_check 1306 bbt is valid, reading.
[ 2.397182@1] aml_nand_read_rsv_info:423,read nbbt info at 280000
[ 2.403441@1] nenv: info size=0x10000 max_scan_blk=32, start_blk=24
[ 2.409869@1] get_free_node 43: bitmap=7
[ 2.413388@1] get_free_node 55: bitmap=f
[ 2.417479@1] get_free_node 43: bitmap=f
[ 2.421188@1] get_free_node 55: bitmap=1f
[ 2.425366@1] get_free_node 43: bitmap=1f
[ 2.429161@1] get_free_node 55: bitmap=3f
[ 2.433339@1] get_free_node 43: bitmap=3f
[ 2.437134@1] get_free_node 55: bitmap=7f
[ 2.441312@1] get_free_node 43: bitmap=7f
[ 2.445108@1] get_free_node 55: bitmap=ff
[ 2.449286@1] get_free_node 43: bitmap=ff
[ 2.453081@1] get_free_node 55: bitmap=1ff
[ 2.457346@1] get_free_node 43: bitmap=1ff
[ 2.461228@1] get_free_node 55: bitmap=3ff
[ 2.465301@1] nenv : phy_blk_addr=24, ec=0, phy_page_addr=0, timestamp=1
[ 2.471971@1] nenv free list:
[ 2.474919@1] blockN=25, ec=-1, dirty_flag=0
[ 2.479166@1] blockN=26, ec=-1, dirty_flag=0
[ 2.483413@1] blockN=27, ec=-1, dirty_flag=0
[ 2.487659@1] blockN=28, ec=-1, dirty_flag=0
[ 2.491906@1] blockN=29, ec=-1, dirty_flag=0
[ 2.496153@1] blockN=30, ec=-1, dirty_flag=0
[ 2.500399@1] blockN=31, ec=-1, dirty_flag=0
[ 2.504646@1] aml_nand_scan_rsv_info 1141: page_num=32
[ 2.521872@1] nenv valid addr: 310000
[ 2.521906@1] nkey: info size=0x8000 max_scan_blk=40, start_blk=32
[ 2.526264@1] get_free_node 43: bitmap=3ff
[ 2.530145@1] get_free_node 55: bitmap=7ff
[ 2.534410@1] get_free_node 43: bitmap=7ff
[ 2.538292@1] get_free_node 55: bitmap=fff
[ 2.542557@1] get_free_node 43: bitmap=fff
[ 2.546439@1] get_free_node 55: bitmap=1fff
[ 2.550790@1] get_free_node 43: bitmap=1fff
[ 2.554759@1] get_free_node 55: bitmap=3fff
[ 2.559110@1] get_free_node 43: bitmap=3fff
[ 2.563079@1] get_free_node 55: bitmap=7fff
[ 2.567430@1] get_free_node 43: bitmap=7fff
[ 2.571399@1] get_free_node 55: bitmap=ffff
[ 2.575750@1] get_free_node 43: bitmap=ffff
[ 2.579718@1] get_free_node 55: bitmap=1ffff
[ 2.584157@1] get_free_node 43: bitmap=1ffff
[ 2.588210@1] get_free_node 55: bitmap=3ffff
[ 2.592459@1] nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
[ 2.599130@1] nkey free list:
[ 2.602076@1] blockN=32, ec=-1, dirty_flag=0
[ 2.606323@1] blockN=33, ec=-1, dirty_flag=0
[ 2.610570@1] blockN=34, ec=-1, dirty_flag=0
[ 2.614816@1] blockN=35, ec=-1, dirty_flag=0
[ 2.619063@1] blockN=36, ec=-1, dirty_flag=0
[ 2.623309@1] blockN=37, ec=-1, dirty_flag=0
[ 2.627557@1] blockN=38, ec=-1, dirty_flag=0
[ 2.631803@1] blockN=39, ec=-1, dirty_flag=0
[ 2.636050@1] aml_nand_scan_rsv_info 1141: page_num=16
[ 2.641163@1] nkey valid addr: fffffffffffe0000
[ 2.645670@1] aml_nand_key_check 1251 NO key exist
[ 2.650436@1] ndtb: info size=0x20000 max_scan_blk=44, start_blk=40
[ 2.657060@1] get_free_node 43: bitmap=3ffff
[ 2.660925@1] get_free_node 55: bitmap=7ffff
[ 2.665371@1] get_free_node 43: bitmap=7ffff
[ 2.669419@1] get_free_node 55: bitmap=fffff
[ 2.673856@1] get_free_node 43: bitmap=fffff
[ 2.677912@1] get_free_node 55: bitmap=1fffff
[ 2.682245@1] ndtb : phy_blk_addr=40, ec=0, phy_page_addr=0, timestamp=1
[ 2.688916@1] ndtb free list:
[ 2.691846@1] blockN=41, ec=-1, dirty_flag=0
[ 2.696110@1] blockN=42, ec=-1, dirty_flag=0
[ 2.700356@1] blockN=43, ec=-1, dirty_flag=0
[ 2.704603@1] aml_nand_scan_rsv_info 1141: page_num=64
[ 2.721828@1] ndtb valid addr: 500000
[ 2.721862@1] nddr: info size=0x20000 max_scan_blk=46, start_blk=44
[ 2.726308@1] get_free_node 43: bitmap=1fffff
[ 2.730449@1] get_free_node 55: bitmap=3fffff
[ 2.734973@1] get_free_node 43: bitmap=3fffff
[ 2.739115@1] get_free_node 55: bitmap=7fffff
[ 2.743449@1] nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
[ 2.750119@1] nddr free list:
[ 2.753067@1] blockN=44, ec=-1, dirty_flag=0
[ 2.757313@1] blockN=45, ec=-1, dirty_flag=0
[ 2.761560@1] aml_nand_scan_rsv_info 1141: page_num=64
[ 2.766673@1] nddr valid addr: fffffffffffe0000
[ 2.771181@1] aml_nand_ddr_check 1281 NO ddr exist
[ 2.775951@1] tpl: off 8388608, size 8388608
[ 2.907513@1] Creating 6 MTD partitions on "nandnormal":
[ 2.907561@1] 0x000000800000-0x000001000000 : "tpl"
[ 2.918836@1] 0x000001000000-0x000001200000 : "misc"
[ 2.922311@1] 0x000001200000-0x000002200000 : "recovery"
[ 2.934076@1] 0x000002200000-0x000004200000 : "boot"
[ 2.953278@1] 0x000004200000-0x000004700000 : "config"
[ 2.957908@1] 0x000004700000-0x000010000000 : "nvdata"
[ 3.059021@2] nandnormal initialized ok
[ 3.059128@2] aml_ubootenv_init: register env chardev
[ 3.062860@2] aml_ubootenv_init: register env chardev OK
[ 3.067707@2] amlnf_dtb_init: register dtb cdev
[ 3.072666@2] amlnf_dtb_init: register dtd cdev OK
[ 3.076864@2] mtd_nand_probe 267 , err = 0
[ 3.082011@3] aml_vrtc rtc: rtc core: registered aml_vrtc as rtc0
[ 3.087448@3] input: aml_vkeypad as /devices/platform/rtc/input/input0
[ 3.094438@2] unifykey: storage in base: 0xffffffc005000000
[ 3.099069@2] unifykey: storage out base: 0xffffffc005040000
[ 3.104660@2] unifykey: storage block base: 0xffffffc005080000
[ 3.110471@2] unifykey: probe done!
[ 3.114665@2] unifykey: no efuse-version set, use default value: -1
[ 3.120198@2] unifykey: key unify config unifykey-num is 6
[ 3.125707@2] unifykey: key unify fact unifykey-num is 6
[ 3.130931@2] unifykey: unifykey_devno: f200000
[ 3.135925@0] unifykey: device unifykeys created ok
[ 3.140428@0] unifykey: aml_unifykeys_init done!
[ 3.145314@0] sysled: module init
[ 3.148773@0] meson_wdt ffd0f0d0.watchdog: start watchdog
[ 3.153565@0] meson_wdt ffd0f0d0.watchdog: creat work queue for watch dog
[ 3.161034@2] meson_wdt ffd0f0d0.watchdog: AML Watchdog Timer probed done
[ 3.169705@3] dmc_monitor_probe
[ 3.179445@3] defendkey defendkey: Reserved memory is not enough!
[ 3.179940@3] defendkey: probe of defendkey failed with error -22
[ 3.186375@3] GACT probability NOT on
[ 3.189708@3] Mirror/redirect action on
[ 3.193473@3] u32 classifier
[ 3.196289@3] Actions configured
[ 3.199870@3] Netfilter messages via NETLINK v0.30.
[ 3.205142@3] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 3.211346@3] ctnetlink v0.93: registering with nfnetlink.
[ 3.217212@0] xt_time: kernel timezone is -0000
[ 3.220941@0] ipip: IPv4 and MPLS over IPv4 tunneling driver
[ 3.227555@0] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.232284@0] arp_tables: arp_tables: (C) 2002 David S. Miller
[ 3.237745@0] Initializing XFRM netlink socket
[ 3.243252@0] NET: Registered protocol family 10
[ 3.248993@0] mip6: Mobile IPv6
[ 3.249814@0] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 3.255780@0] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 3.263749@0] NET: Registered protocol family 17
[ 3.266078@0] NET: Registered protocol family 15
[ 3.270650@0] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 3.283808@0] l2tp_core: L2TP core driver, V2.0
[ 3.288195@0] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 3.293123@0] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 3.298862@0] l2tp_netlink: L2TP netlink interface
[ 3.303684@0] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 3.309735@0] l2tp_debugfs: L2TP debugfs support
[ 3.314271@0] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 3.320922@0] NET: Registered protocol family 35
[ 3.325858@0] Key type dns_resolver registered
[ 3.330444@0] Registered swp emulation handler
[ 3.334310@0] Registered cp15_barrier emulation handler
[ 3.339499@0] Registered setend emulation handler
[ 3.344241@0] disable EAS feature
[ 3.349223@3] registered taskstats version 1
[ 3.365403@2] dwc3 ff500000.dwc3: Configuration mismatch. dr_mode forced to host
[ 3.871823@2] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 3.871913@2] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 3.880190@2] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f664 hci version 0x100 quirks 0x02010010
[ 3.888663@2] xhci-hcd xhci-hcd.0.auto: irq 22, io mem 0xff500000
[ 3.896160@3] hub 1-0:1.0: USB hub found
[ 3.898595@3] hub 1-0:1.0: 1 port detected
[ 3.903191@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 3.908215@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 3.916107@3] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.925623@2] hub 2-0:1.0: USB hub found
[ 3.928166@2] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.935515@2] usb usb2: Unsupported the hub
[ 3.940374@2] aml_vrtc rtc: setting system clock to 2025-03-05 18:36:25 UTC (1741199785)
[ 3.948332@2] dwc_otg ff400000.dwc2_a: dwc_otg_driver_probe(ffffffc00cd93000)
[ 3.948410@2] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: ffe09000, ctrl: 0
[ 3.956291@2] dwc_otg ff400000.dwc2_a: base=0xffffff8008580000
[ 3.956303@2] dwc_otg ff400000.dwc2_a: dwc_otg_device=0xffffffc00b396200
[ 4.056905@2] dwc_otg: Core Release: 3.10a
[ 4.056961@2] dwc_otg: Setting default values for core params
[ 4.061147@2] dwc_otg: curmode: 0, host_only: 0
[ 4.065659@2] dwc_otg ff400000.dwc2_a: DMA config: BURST_DEFAULT
[ 4.078175@2] dwc_otg: Using Buffer DMA mode
[ 4.078212@2] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
[ 4.082119@2] dwc_otg: Working on port type = SLAVE
[ 4.086976@2] dwc_otg: Dedicated Tx FIFOs mode
[ 4.093881@2] thermal thermal_zone0: binding zone soc_thermal with cdev thermal-cpufreq-0 failed:-22
[ 4.100706@2] cpucore_cooling_register, max_cpu_core_num:4
[ 4.113303@2] gxbb_pm: enter meson_pm_probe!
[ 4.113361@2] no vddio3v3_en pin
[ 4.115009@2] pm-meson aml_pm: Can't get switch_clk81
[ 4.120120@2] gxbb_pm: meson_pm_probe done
[ 4.125062@2] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
[ 4.131313@2] Freeing unused kernel memory: 3648K
[ 4.145451@2] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
[ 4.400803@0] ubi0: attaching mtd5
[ 4.419315@0] ubi0: scanning is finished
[ 4.423945@2] ubi0: attached mtd5 (name "config", size 5 MiB)
[ 4.424072@2] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 4.431123@2] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 4.438046@2] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 4.445143@2] ubi0: good PEBs: 40, bad PEBs: 0, corrupted PEBs: 0
[ 4.451216@2] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 4.458576@2] ubi0: max/mean erase counter: 11/5, WL threshold: 4096, image sequence number: 133719375
[ 4.467856@2] ubi0: available PEBs: 0, total reserved PEBs: 40, PEBs reserved for bad PEB handling: 4
[ 4.477061@0] ubi0: background thread "ubi_bgt0d" started, PID 1076
[ 4.490212@3] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 1080
[ 4.523777@1] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "config_data"
[ 4.526219@1] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 4.536235@1] UBIFS (ubi0:0): FS size: 2793472 bytes (2 MiB, 22 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
[ 4.546467@1] UBIFS (ubi0:0): reserved for root: 131942 bytes (128 KiB)
[ 4.553048@1] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID B4B290C6-0E09-4CF7-8946-F76A3A1E66EA, small LPT model
[ 4.577597@0] ubi2: attaching mtd6
[ 5.252286@0] ubi2: scanning is finished
[ 5.259641@1] ubi2: attached mtd6 (name "nvdata", size 185 MiB)
[ 5.259946@1] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 5.267059@1] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 5.273921@1] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.281015@1] ubi2: good PEBs: 1480, bad PEBs: 0, corrupted PEBs: 0
[ 5.287263@1] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 5.294624@1] ubi2: max/mean erase counter: 1348/517, WL threshold: 4096, image sequence number: 3408866948
[ 5.304336@1] ubi2: available PEBs: 0, total reserved PEBs: 1480, PEBs reserved for bad PEB handling: 4
[ 5.313785@3] ubi2: background thread "ubi_bgt2d" started, PID 1088
[ 5.326543@2] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 1092
[ 5.375068@0] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "nvdada_log"
[ 5.377418@0] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 5.387440@0] UBIFS (ubi2:0): FS size: 185384960 bytes (176 MiB, 1460 LEBs), journal size 9269248 bytes (8 MiB, 73 LEBs)
[ 5.398267@0] UBIFS (ubi2:0): reserved for root: 4952683 bytes (4836 KiB)
[ 5.405030@0] UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID 6C0ABFDD-4BCA-41D8-BB4A-20A4CC6237C9, small LPT model
[ 5.641130@0] eth0: device MAC address 02:66:70:f3:2f:4d
[ 5.725467@3] meson6-dwmac ff3f0000.ethernet eth0: fail to init PTP.
[ 5.726763@3] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 5.977233@2] uart_trans: loading out-of-tree module taints kernel.
[ 5.979817@2] register uart_trans chrdev success.
[ 5.983012@2] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 0 to 9600
[ 5.990632@2] tty port open success [/dev/ttyS3]!
[ 5.995326@2] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 9600 to 115200
[ 6.003935@2] init sucess for tty struct (246:3) [/dev/ttyS3]
[ 6.009916@2] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 0 to 9600
[ 6.017487@2] tty port open success [/dev/ttyS2]!
[ 6.022180@2] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 9600 to 115200
[ 6.030558@2] init sucess for tty struct (246:2) [/dev/ttyS2]
[ 6.036741@2] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 0 to 9600
[ 6.044332@2] tty port open success [/dev/ttyS1]!
[ 6.048982@2] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 9600 to 115200
[ 6.057389@2] init sucess for tty struct (246:1) [/dev/ttyS1]
[ 6.063637@3] create workqueue success!
[ 7.768980@3] meson6-dwmac ff3f0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
[ 7.772087@3] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 41.035581@3] uart trans dev open.
[ 41.035699@3] uart_buf virt addr = 0xffffffc00da00000
[ 41.038713@3] uart_buf phys addr = 0x0da00000
[ 41.042790@3] uart_buf pfn = 0x0000da00
[ 41.048532@3] uart trans stop send work timer.
[ 41.051891@3] uart trans set chain exist bits:0x7.
[ 41.056322@3] uart trans set work queue count 768.
[ 118.865443@3] uart set baud to: 4098
[ 118.865504@3] uart set baud to: 4098
[ 118.867060@3] uart set baud to: 4098
[ 135.713169@2] uart trans stop send work timer.
[ 144.715275@1] uart trans start send work timer.
[ 166.727247@1] uart trans stop send work timer.
[ 167.739605@1] uart trans stop send work timer.
[ 173.805540@3] uart trans start send work timer.
[ 184.788205@0] nf_conntrack: default automatic helper assignment has been turned off for security reasons and CT-based firewall rule not found. Use the iptables CT target to attach helpers instead.
[ 242.697792@2] uart trans dev open.
[ 242.697909@2] uart_buf virt addr = 0xffffffc00da00000
[ 242.700607@2] uart_buf phys addr = 0x0da00000
[ 242.705017@2] uart_buf pfn = 0x0000da00
[ 242.709387@2] uart trans stop send work timer.
[ 242.713991@2] uart trans set chain exist bits:0x7.
[ 242.718562@2] uart trans set work queue count 768.
[ 320.521412@3] uart set baud to: 4098
[ 320.521473@3] uart set baud to: 4098
[ 320.523034@3] uart set baud to: 4098
[ 337.367483@2] uart trans stop send work timer.
[ 354.836430@3] uart trans start send work timer.
[ 368.378073@2] uart trans stop send work timer.
[ 369.390359@1] uart trans stop send work timer.
[ 370.583667@3] uart trans start send work timer.
[ 446.398429@1] uart trans dev open.
[ 446.398546@1] uart_buf virt addr = 0xffffffc00da00000
[ 446.401307@1] uart_buf phys addr = 0x0da00000
[ 446.405614@1] uart_buf pfn = 0x0000da00
[ 446.409960@1] uart trans stop send work timer.
[ 446.414522@1] uart trans set chain exist bits:0x7.
[ 446.419129@1] uart trans set work queue count 768.
[ 524.186077@0] uart set baud to: 4098
[ 524.186138@0] uart set baud to: 4098
[ 524.187655@0] uart set baud to: 4098
[ 541.032658@1] uart trans stop send work timer.
[ 542.045987@1] uart trans stop send work timer.
[ 564.815374@1] uart trans start send work timer.
===========================================Miner log===========================================
2025-03-05 18:36:32 Open miner sn file /config/mac error
2025-03-05 18:36:32 Miner compile time: Fri Feb 2 17:03:40 CST 2024 type: Antminer S21 sn :DGAHFAUBDJCBG021Y mac:
2025-03-05 18:36:33 This is fix-freq version
2025-03-05 18:36:33 Miner compile time: Fri Feb 2 17:03:40 CST 2024 type: Antminer S21
2025-03-05 18:36:33 Miner sn: DGAHFAUBDJCBG021Y
2025-03-05 18:36:33 commit version: e676fcaf 2023-11-18 17:15:18, build by: jenkins 2024-02-02 17:17:08
2025-03-05 18:36:33 opt_multi_version = 1
2025-03-05 18:36:33 opt_bitmain_ab = 1
2025-03-05 18:36:33 mid_auto_gen = 1
2025-03-05 18:36:33 opt_bitmain_work_mode = 0
2025-03-05 18:36:33 port 439 already exported
2025-03-05 18:36:33 port 454 already exported
2025-03-05 18:36:33 port 440 already exported
2025-03-05 18:36:33 port 455 already exported
2025-03-05 18:36:33 port 441 already exported
2025-03-05 18:36:33 port 456 already exported
2025-03-05 18:36:33 port 438 already exported
2025-03-05 18:36:33 port 453 already exported
2025-03-05 18:36:33 port 446 already exported
2025-03-05 18:36:33 port 445 already exported
2025-03-05 18:36:33 Note: front fan is power on!
2025-03-05 18:36:33 Note: rear fan is power on!
2025-03-05 18:36:33 start the http server
2025-03-05 18:36:33 httpserver:6060 started ok
2025-03-05 18:36:33 load machine BHB68601 conf
2025-03-05 18:36:33 machine : BHB68601
2025-03-05 18:36:33 get test_loop_securely_find_asic_num failed
2025-03-05 18:36:33 abandon mix board!
2025-03-05 18:36:33 get mix boardname[0][BHB68601], name:BHB68601
2025-03-05 18:36:34 bad chain id = 3
2025-03-05 18:36:37 bad chain id = 3
2025-03-05 18:36:39 power off
2025-03-05 18:36:40 ==========================capability start==========================
2025-03-05 18:36:40 board num = 3
2025-03-05 18:36:40 board id = 0, chain num = 1
2025-03-05 18:36:40 chain id = 0
2025-03-05 18:36:40 board id = 1, chain num = 1
2025-03-05 18:36:40 chain id = 1
2025-03-05 18:36:40 board id = 2, chain num = 1
2025-03-05 18:36:40 chain id = 2
2025-03-05 18:36:40 ==========================capability end============================
2025-03-05 18:36:40 chain num = 3
2025-03-05 18:36:44 load chain 0 eeprom data
2025-03-05 18:36:47 load chain 1 eeprom data
2025-03-05 18:36:50 load chain 2 eeprom data
2025-03-05 18:36:50 eeprom load ret:0
2025-03-05 18:36:50 miner:BHB68601,board_name:BHB68606
2025-03-05 18:36:50 miner:BHB68602,board_name:BHB68606
2025-03-05 18:36:50 miner:BHB68603,board_name:BHB68606
2025-03-05 18:36:50 miner:BHB68606,board_name:BHB68606
2025-03-05 18:36:50 load machine BHB68606 conf
2025-03-05 18:36:50 machine : BHB68606
2025-03-05 18:36:50 get test_loop_securely_find_asic_num failed
2025-03-05 18:36:50 abandon mix board!
2025-03-05 18:36:50 get mix boardname[0][BHB68606], name:BHB68606
2025-03-05 18:36:50 update conf to BHB68606 complete
2025-03-05 18:36:50 reload start.
2025-03-05 18:36:50 ==========================capability start==========================
2025-03-05 18:36:50 board num = 3
2025-03-05 18:36:50 board id = 0, chain num = 1
2025-03-05 18:36:50 chain id = 0
2025-03-05 18:36:50 board id = 1, chain num = 1
2025-03-05 18:36:50 chain id = 1
2025-03-05 18:36:50 board id = 2, chain num = 1
2025-03-05 18:36:50 chain id = 2
2025-03-05 18:36:50 ==========================capability end============================
2025-03-05 18:36:50 chain num = 3
2025-03-05 18:36:53 load chain 0 eeprom data
2025-03-05 18:36:57 load chain 1 eeprom data
2025-03-05 18:37:00 load chain 2 eeprom data
2025-03-05 18:37:00 eeprom load ret:0
2025-03-05 18:37:00 create thread get_nonce_and_register_thread
2025-03-05 18:37:00 fixed working voltage = 1415
2025-03-05 18:37:00 Chain
2025-03-05 18:37:00 Chain
2025-03-05 18:37:00 Chain [1] PCB Version: 0x0100
2025-03-05 18:37:00 Chain [1] BOM Version: 0x0000
2025-03-05 18:37:00 Chain [2] PCB Version: 0x0100
2025-03-05 18:37:00 Chain [2] BOM Version: 0x0000
2025-03-05 18:37:00 bad chain id = 3
2025-03-05 18:37:03 Fan check passed.
2025-03-05 18:37:03 init fan pid target=60
2025-03-05 18:37:03 max sensor num = 4
2025-03-05 18:37:03 STATUS_INITED: soc init done!
2025-03-05 18:37:03 asic_temperature_and_voltage_monitor_thread start...
2025-03-05 18:37:03 temperature_monitor_thread start...
2025-03-05 18:37:05 start to init...
2025-03-05 18:37:05 i2c_sim_init start
2025-03-05 18:37:05 init gpio477
2025-03-05 18:37:05 init gpio476
2025-03-05 18:37:05 i2c_sim_init end
2025-03-05 18:37:07 power open power_version = 0xc1
2025-03-05 18:37:09 power fw_version = 0x1e08
2025-03-05 18:37:12 power is Calibrated
2025-03-05 18:37:13 power sn:DGQG335BDJDJH0205
2025-03-05 18:37:13 enable_power_calibration,calibration date:211208.
2025-03-05 18:37:14 power type version: 0x00c1
2025-03-05 18:37:16 power history status: 0
2025-03-05 18:37:18 disable power watchdog: 0x0000
2025-03-05 18:37:19 Initializing the power, please wait, this may take up to 2 minutes...
2025-03-05 18:37:49 Slept 30 seconds, diff = 0.
2025-03-05 18:37:59 set_voltage_by_steps to 1500.
2025-03-05 18:38:01 power on
2025-03-05 18:38:16 bad chain id = 3
2025-03-05 18:38:21 start up min temp by 75a = 17
2025-03-05 18:38:30 Chain[0]: find 0 asic, times 0
2025-03-05 18:38:34 Chain[0]: find 0 asic, times 1
2025-03-05 18:38:38 Chain[0]: find 0 asic, times 2
2025-03-05 18:38:38 Chain 0 only find 0 asic, will power off hash board 0
2025-03-05 18:38:38 Sweep error string = J1:2.
2025-03-05 18:38:38 ERROR_ASIC_NUM: asic number is not right
2025-03-05 18:38:38 stop_mining: asic number is not right
2025-03-05 18:38:38 uninit_temp_info
2025-03-05 18:38:38 do not read temp anymore...
2025-03-05 18:38:38 uninit_asic_temp_vol_info
2025-03-05 18:38:38 do not read asic_temp_vol anymore...
2025-03-05 18:38:38 cancel thread thread_id_rd_nonce_reg
2025-03-05 18:38:38 ****power off hashboard****
2025-03-05 18:38:38 power off
2025-03-05 18:38:38 asic_temperature_and_voltage_monitor_thread exit
2025-03-05 18:38:39 temp monitor thread exit
2025-03-05 18:38:39 ERROR_SOC_INIT: soc init failed!
2025-03-05 18:38:39 fail to open counter file, err:No such file or directory
2025-03-05 18:38:47 Version num 65536
2025-03-05 18:38:47 Mask num 0x1fffe000
2025-03-05 18:38:47 Note: addrInterval or corenum is not initialized.
2025-03-05 18:39:09 stop_mining_and_restart: soc init failed!
2025-03-05 18:39:09 ****power off hashboard****
2025-03-05 18:39:09 power off
2025-03-05 18:39:10 restart
2025-03-05 18:39:10 ****power off hashboard****
2025-03-05 18:39:10 power off
2025-03-05 18:39:41 httpserver6060 quit!
2025-03-05 18:39:55 Open miner sn file /config/mac error
2025-03-05 18:39:55 Miner compile time: Fri Feb 2 17:03:40 CST 2024 type: Antminer S21 sn :DGAHFAUBDJCBG021Y mac:
2025-03-05 18:39:56 This is fix-freq version
2025-03-05 18:39:56 Miner compile time: Fri Feb 2 17:03:40 CST 2024 type: Antminer S21
2025-03-05 18:39:56 Miner sn: DGAHFAUBDJCBG021Y
2025-03-05 18:39:56 commit version: e676fcaf 2023-11-18 17:15:18, build by: jenkins 2024-02-02 17:17:08
2025-03-05 18:39:56 opt_multi_version = 1
2025-03-05 18:39:56 opt_bitmain_ab = 1
2025-03-05 18:39:56 mid_auto_gen = 1
2025-03-05 18:39:56 opt_bitmain_work_mode = 0
2025-03-05 18:39:56 port 439 already exported
2025-03-05 18:39:56 port 454 already exported
2025-03-05 18:39:56 port 440 already exported
2025-03-05 18:39:56 port 455 already exported
2025-03-05 18:39:56 port 441 already exported
2025-03-05 18:39:56 port 456 already exported
2025-03-05 18:39:56 port 438 already exported
2025-03-05 18:39:56 port 453 already exported
2025-03-05 18:39:56 port 446 already exported
2025-03-05 18:39:56 port 445 already exported
2025-03-05 18:39:56 Note: front fan is power on!
2025-03-05 18:39:56 Note: rear fan is power on!
2025-03-05 18:39:56 start the http server
2025-03-05 18:39:56 httpserver:6060 started ok
2025-03-05 18:39:56 load machine BHB68601 conf
2025-03-05 18:39:56 machine : BHB68601
2025-03-05 18:39:56 get test_loop_securely_find_asic_num failed
2025-03-05 18:39:56 abandon mix board!
2025-03-05 18:39:56 get mix boardname[0][BHB68601], name:BHB68601
2025-03-05 18:39:56 bad chain id = 3
2025-03-05 18:39:59 bad chain id = 3
2025-03-05 18:40:01 power off
2025-03-05 18:40:02 ==========================capability start==========================
2025-03-05 18:40:02 board num = 3
2025-03-05 18:40:02 board id = 0, chain num = 1
2025-03-05 18:40:02 chain id = 0
2025-03-05 18:40:02 board id = 1, chain num = 1
2025-03-05 18:40:02 chain id = 1
2025-03-05 18:40:02 board id = 2, chain num = 1
2025-03-05 18:40:02 chain id = 2
2025-03-05 18:40:02 ==========================capability end============================
2025-03-05 18:40:02 chain num = 3
2025-03-05 18:40:05 load chain 0 eeprom data
2025-03-05 18:40:09 load chain 1 eeprom data
2025-03-05 18:40:12 load chain 2 eeprom data
2025-03-05 18:40:12 eeprom load ret:0
2025-03-05 18:40:12 miner:BHB68601,board_name:BHB68606
2025-03-05 18:40:12 miner:BHB68602,board_name:BHB68606
2025-03-05 18:40:12 miner:BHB68603,board_name:BHB68606
2025-03-05 18:40:12 miner:BHB68606,board_name:BHB68606
2025-03-05 18:40:12 load machine BHB68606 conf
2025-03-05 18:40:12 machine : BHB68606
2025-03-05 18:40:12 get test_loop_securely_find_asic_num failed
2025-03-05 18:40:12 abandon mix board!
2025-03-05 18:40:12 get mix boardname[0][BHB68606], name:BHB68606
2025-03-05 18:40:12 update conf to BHB68606 complete
2025-03-05 18:40:12 reload start.
2025-03-05 18:40:12 ==========================capability start==========================
2025-03-05 18:40:12 board num = 3
2025-03-05 18:40:12 board id = 0, chain num = 1
2025-03-05 18:40:12 chain id = 0
2025-03-05 18:40:12 board id = 1, chain num = 1
2025-03-05 18:40:12 chain id = 1
2025-03-05 18:40:12 board id = 2, chain num = 1
2025-03-05 18:40:12 chain id = 2
2025-03-05 18:40:12 ==========================capability end============================
2025-03-05 18:40:12 chain num = 3
2025-03-05 18:40:15 load chain 0 eeprom data
2025-03-05 18:40:18 load chain 1 eeprom data
2025-03-05 18:40:22 load chain 2 eeprom data
2025-03-05 18:40:22 eeprom load ret:0
2025-03-05 18:40:22 create thread get_nonce_and_register_thread
2025-03-05 18:40:22 fixed working voltage = 1415
2025-03-05 18:40:22 Chain
2025-03-05 18:40:22 Chain
2025-03-05 18:40:22 Chain [1] PCB Version: 0x0100
2025-03-05 18:40:22 Chain [1] BOM Version: 0x0000
2025-03-05 18:40:22 Chain [2] PCB Version: 0x0100
2025-03-05 18:40:22 Chain [2] BOM Version: 0x0000
2025-03-05 18:40:22 bad chain id = 3
2025-03-05 18:40:25 Fan check passed.
2025-03-05 18:40:25 init fan pid target=60
2025-03-05 18:40:25 max sensor num = 4
2025-03-05 18:40:25 STATUS_INITED: soc init done!
2025-03-05 18:40:25 asic_temperature_and_voltage_monitor_thread start...
2025-03-05 18:40:25 temperature_monitor_thread start...
2025-03-05 18:40:27 start to init...
2025-03-05 18:40:27 i2c_sim_init start
2025-03-05 18:40:27 i2c_sim_init end
2025-03-05 18:40:29 power open power_version = 0xc1
2025-03-05 18:40:30 power fw_version = 0x1e08
2025-03-05 18:40:34 power is Calibrated
2025-03-05 18:40:34 power sn:DGQG335BDJDJH0205
2025-03-05 18:40:34 enable_power_calibration,calibration date:211208.
2025-03-05 18:40:36 power type version: 0x00c1
2025-03-05 18:40:38 power history status: 0
2025-03-05 18:40:40 disable power watchdog: 0x0000
2025-03-05 18:40:41 Initializing the power, please wait, this may take up to 2 minutes...
2025-03-05 18:41:11 Slept 30 seconds, diff = 0.
2025-03-05 18:41:21 set_voltage_by_steps to 1500.
2025-03-05 18:41:23 power on
2025-03-05 18:41:38 bad chain id = 3
2025-03-05 18:41:43 start up min temp by 75a = 18
2025-03-05 18:41:51 Chain[0]: find 0 asic, times 0
2025-03-05 18:41:55 Chain[0]: find 0 asic, times 1
2025-03-05 18:41:59 Chain[0]: find 0 asic, times 2
2025-03-05 18:41:59 Chain 0 only find 0 asic, will power off hash board 0
2025-03-05 18:41:59 Sweep error string = J1:2.
2025-03-05 18:41:59 ERROR_ASIC_NUM: asic number is not right
2025-03-05 18:41:59 stop_mining: asic number is not right
2025-03-05 18:41:59 uninit_temp_info
2025-03-05 18:41:59 do not read temp anymore...
2025-03-05 18:41:59 uninit_asic_temp_vol_info
2025-03-05 18:41:59 do not read asic_temp_vol anymore...
2025-03-05 18:41:59 cancel thread thread_id_rd_nonce_reg
2025-03-05 18:41:59 ****power off hashboard****
2025-03-05 18:41:59 power off
2025-03-05 18:42:00 asic_temperature_and_voltage_monitor_thread exit
2025-03-05 18:42:00 temp monitor thread exit
2025-03-05 18:42:00 ERROR_SOC_INIT: soc init failed!
2025-03-05 18:42:17 Version num 65536
2025-03-05 18:42:17 Mask num 0x1fffe000
2025-03-05 18:42:17 Note: addrInterval or corenum is not initialized.
2025-03-05 18:42:30 stop_mining_and_restart: soc init failed!
2025-03-05 18:42:30 ****power off hashboard****
2025-03-05 18:42:30 power off
2025-03-05 18:42:31 restart
2025-03-05 18:42:31 ****power off hashboard****
2025-03-05 18:42:31 power off
2025-03-05 18:43:02 httpserver6060 quit!
2025-03-05 18:43:18 Open miner sn file /config/mac error
2025-03-05 18:43:18 Miner compile time: Fri Feb 2 17:03:40 CST 2024 type: Antminer S21 sn :DGAHFAUBDJCBG021Y mac:
2025-03-05 18:43:20 This is fix-freq version
2025-03-05 18:43:20 Miner compile time: Fri Feb 2 17:03:40 CST 2024 type: Antminer S21
2025-03-05 18:43:20 Miner sn: DGAHFAUBDJCBG021Y
2025-03-05 18:43:20 commit version: e676fcaf 2023-11-18 17:15:18, build by: jenkins 2024-02-02 17:17:08
2025-03-05 18:43:20 opt_multi_version = 1
2025-03-05 18:43:20 opt_bitmain_ab = 1
2025-03-05 18:43:20 mid_auto_gen = 1
2025-03-05 18:43:20 opt_bitmain_work_mode = 0
2025-03-05 18:43:20 port 439 already exported
2025-03-05 18:43:20 port 454 already exported
2025-03-05 18:43:20 port 440 already exported
2025-03-05 18:43:20 port 455 already exported
2025-03-05 18:43:20 port 441 already exported
2025-03-05 18:43:20 port 456 already exported
2025-03-05 18:43:20 port 438 already exported
2025-03-05 18:43:20 port 453 already exported
2025-03-05 18:43:20 port 446 already exported
2025-03-05 18:43:20 port 445 already exported
2025-03-05 18:43:20 Note: front fan is power on!
2025-03-05 18:43:20 Note: rear fan is power on!
2025-03-05 18:43:20 start the http server
2025-03-05 18:43:20 httpserver:6060 started ok
2025-03-05 18:43:20 load machine BHB68601 conf
2025-03-05 18:43:20 machine : BHB68601
2025-03-05 18:43:20 get test_loop_securely_find_asic_num failed
2025-03-05 18:43:20 abandon mix board!
2025-03-05 18:43:20 get mix boardname[0][BHB68601], name:BHB68601
2025-03-05 18:43:20 bad chain id = 3
2025-03-05 18:43:23 bad chain id = 3
2025-03-05 18:43:25 power off
2025-03-05 18:43:26 ==========================capability start==========================
2025-03-05 18:43:26 board num = 3
2025-03-05 18:43:26 board id = 0, chain num = 1
2025-03-05 18:43:26 chain id = 0
2025-03-05 18:43:26 board id = 1, chain num = 1
2025-03-05 18:43:26 chain id = 1
2025-03-05 18:43:26 board id = 2, chain num = 1
2025-03-05 18:43:26 chain id = 2
2025-03-05 18:43:26 ==========================capability end============================
2025-03-05 18:43:26 chain num = 3
2025-03-05 18:43:29 load chain 0 eeprom data
2025-03-05 18:43:32 load chain 1 eeprom data
2025-03-05 18:43:36 load chain 2 eeprom data
2025-03-05 18:43:36 eeprom load ret:0
2025-03-05 18:43:36 miner:BHB68601,board_name:BHB68606
2025-03-05 18:43:36 miner:BHB68602,board_name:BHB68606
2025-03-05 18:43:36 miner:BHB68603,board_name:BHB68606
2025-03-05 18:43:36 miner:BHB68606,board_name:BHB68606
2025-03-05 18:43:36 load machine BHB68606 conf
2025-03-05 18:43:36 machine : BHB68606
2025-03-05 18:43:36 get test_loop_securely_find_asic_num failed
2025-03-05 18:43:36 abandon mix board!
2025-03-05 18:43:36 get mix boardname[0][BHB68606], name:BHB68606
2025-03-05 18:43:36 update conf to BHB68606 complete
2025-03-05 18:43:36 reload start.
2025-03-05 18:43:36 ==========================capability start==========================
2025-03-05 18:43:36 board num = 3
2025-03-05 18:43:36 board id = 0, chain num = 1
2025-03-05 18:43:36 chain id = 0
2025-03-05 18:43:36 board id = 1, chain num = 1
2025-03-05 18:43:36 chain id = 1
2025-03-05 18:43:36 board id = 2, chain num = 1
2025-03-05 18:43:36 chain id = 2
2025-03-05 18:43:36 ==========================capability end============================
2025-03-05 18:43:36 chain num = 3
2025-03-05 18:43:39 load chain 0 eeprom data
2025-03-05 18:43:42 load chain 1 eeprom data
2025-03-05 18:43:45 load chain 2 eeprom data
2025-03-05 18:43:45 eeprom load ret:0
2025-03-05 18:43:45 create thread get_nonce_and_register_thread
2025-03-05 18:43:45 fixed working voltage = 1415
2025-03-05 18:43:45 Chain
2025-03-05 18:43:45 Chain
2025-03-05 18:43:45 Chain [1] PCB Version: 0x0100
2025-03-05 18:43:45 Chain [1] BOM Version: 0x0000
2025-03-05 18:43:45 Chain [2] PCB Version: 0x0100
2025-03-05 18:43:45 Chain [2] BOM Version: 0x0000
2025-03-05 18:43:45 bad chain id = 3
2025-03-05 18:43:48 Fan check passed.
2025-03-05 18:43:48 init fan pid target=60
2025-03-05 18:43:48 max sensor num = 4
2025-03-05 18:43:48 STATUS_INITED: soc init done!
2025-03-05 18:43:48 asic_temperature_and_voltage_monitor_thread start...
2025-03-05 18:43:48 temperature_monitor_thread start...
2025-03-05 18:43:51 start to init...
2025-03-05 18:43:51 i2c_sim_init start
2025-03-05 18:43:51 i2c_sim_init end
2025-03-05 18:43:52 power open power_version = 0xc1
2025-03-05 18:43:54 power fw_version = 0x1e08
2025-03-05 18:43:58 power is Calibrated
2025-03-05 18:43:58 power sn:DGQG335BDJDJH0205
2025-03-05 18:43:58 enable_power_cal
Show Posts
