so can the L3 only mine ltc ?

i also have been talking to bitfury trying to get the 16nm chip but they always only offer $1m buy order then thay tell me i can buy smaller orders of chips or miners from one of there partners but after many times of asking where to buy they always say we will connect you to them...... time and time again.
i have access to board designers,PCB manufacturing,PCB tooling...........but with all this I CANT GET 1 CHIP...... so frustrating!!!!

someone can buy my 1954 ford f100 for 42. btc
you pay shipping

I SELL ON EBAY AND I ACCEPT BTC
i also say btc accepted in my listing.
sure it goes around ebay but thay get 10% of all my sells and paypal another 4% otherwise 

i have also bought many things for btc on ebay all i do is ask the seller the worst they can say is no

its not your power supply or pool ....ITS THE FIRMWARE !!!!!!!
there is a power setting that's messed up in it.
the power settings in the miner did not save properly at the factory so after 20 min to a few hrs it drops to nothing or lo.
look in your advanced settings under your clock speed is the voltage it is probably empty or shows .0770 this is wrong

i explained all this on this sight but no one would listen.

the firmware is screwed up and if you don't uncheck the save settings box above your flashing file on your first flash back it will crash during flash and will be unbootable!!!!!!
if you don't uncheck save settings box before the next two flashes it wont save the power properly.

try it on your worst one and fallow my instructions exactly and it will run perfectly ! then you can do it to the rest

so download the first 3 bitmain s3+ firmware from there sight
antMiner_S320140826.bin
antMiner_S320141013.bin
antMiner_S320141219.bin

then reboot your miner!!! just so its a fresh start up

when its back up go to update firmware uncheck the save settings box and flash antMiner_S320140826.bin
at this time you will be at ip .99
when its done and back up go back to flash firmware and uncheck the save settings box and flash antMiner_S320141013.bin
when its done and back up go back to flash firmware and uncheck the save settings box and flash antMiner_S320141219.bin
when its back up go to miner settings erase all of there mining and replace with yours then push save and apply
then go to advanced settings click on 225 then push save and apply
then go to your networks and change your ip to what you want from .99 to . (your miner ip)

now type your new ip in search bar and your up and gowning!!!!!!!!!!!!!


i explained this to many people the other day and no one believed me thy thought i was lying. but now you are down.

i have 26 s3's and my s3' were crashing many times a day thy were working good and then crash down to 40 gh/s i have been working on this problem for a month and finely fixed them.
if you had flashed bitmains last firmware 1226 or you have batch 11 that's the problem and reset wont work and if you flash back to earlier program it crashes the miner and is un bootable.
i am willing to enplane step by step how to recover the unbootable miner and flash crashing miners back to good firmware with success. bitmain is making tones of btc telling people the control boards are bad just like thy told me and i fixed it. it took me three hrs to set up and figure it out and now that im setup it only takes 15 minuts to fix a crashed s3's.
if you want the help i can give it and in return it would be nice to get a btc donation for saving you tons of time and money 15s7keW5PNYESG63p2ZWc5GcEkDebx4Awp

its not your power supply or pool ....ITS THE FIRMWARE !!!!!!!
there is a power setting that's messed up in it.
the power settings in the miner did not save properly at the factory so after 20 min to a few hrs it drops to nothing or lo.
look in your advanced settings under your clock speed is the voltage it is probably empty or shows .0770 this is wrong

i explained all this on this sight but no one would listen.

the firmware is screwed up and if you don't uncheck the save settings box above your flashing file on your first flash back it will crash during flash and will be unbootable!!!!!!
if you don't uncheck save settings box before the next two flashes it wont save the power properly.

try it on your worst one and fallow my instructions exactly and it will run perfectly ! then you can do it to the rest

so download the first 3 bitmain s3+ firmware from there sight
antMiner_S320140826.bin
antMiner_S320141013.bin
antMiner_S320141219.bin

then reboot your miner!!! just so its a fresh start up

when its back up go to update firmware uncheck the save settings box and flash antMiner_S320140826.bin
at this time you will be at ip .99
when its done and back up go back to flash firmware and uncheck the save settings box and flash antMiner_S320141013.bin
when its done and back up go back to flash firmware and uncheck the save settings box and flash antMiner_S320141219.bin
when its back up go to miner settings erase all of there mining and replace with yours then push save and apply
then go to advanced settings click on 225 then push save and apply
then go to your networks and change your ip to what you want from .99 to . (your miner ip)

now type your new ip in search bar and your up and gowning!!!!!!!!!!!!!


i explained this to many people the other day and no one believed me thy thought i was lying. but now you are down.

i have 26 s3's and my s3' were crashing many times a day thy were working good and then crash down to 40 gh/s i have been working on this problem for a month and finely fixed them.
if you had flashed bitmains last firmware 1226 or you have batch 11 that's the problem and reset wont work and if you flash back to earlier program it crashes the miner and is un bootable.
i am willing to enplane step by step how to recover the unbootable miner and flash crashing miners back to good firmware with success. bitmain is making tones of btc telling people the control boards are bad just like thy told me and i fixed it. it took me three hrs to set up and figure it out and now that im setup it only takes 15 minuts to fix a crashed s3's.
if you want the help i can give it and in return it would be nice to get a btc donation for saving you tons of time and money 15s7keW5PNYESG63p2ZWc5GcEkDebx4Awp

i explained all this on this sight but no one would listen.

the firmware is screwed up and if you don't uncheck the save settings box above your flashing file  it will crash during flash and will be unbootable.
i explained this to many people the other day and no one believed me thy thought i was lying. but now you are down.
i have 26 s3's and my s3' were crashing many times a day thy were working good and then crash down to 40 gh/s i have been working on this problem for a month and finely fixed them.
if you had flashed bitmains last firmware 1226 thats the problem and reset wont work and if you flash back to earlier program it crashes the miner and is un bootable.
i am willing to enplane step by step how to recover the unbootable miner and flash crashing miners back to good firmware with success. bitmain is making tones of btc telling people the control boards are bad just like thy told me and i fixed it. it took me three hrs to set up and figure it out and now that im setup it only takes 15 minuts to fix a crashed s3's.
if you want the help i can give it and in return it would be nice to get a btc donation for saving you tons of time and money
but it can still be fixed

what exactly are your miners doing?
wont boot?
drops hash down to 0-40-50 gh/s

so what i found out is using pc power supply's is OK but you cant push them to there max or it will just kill them in like a month or so and even tho you are using a good power supply you cant get all the power out of them without using every yellow wire on them or you can smoke and melt the wires.
when i was using all pc psu's i would cut all the plugs off then connect 1 black to 1 green then i would put all the black together and all the yellow together then i would have all the 12v it can do.
so with your psu i would divide all black and yellow into groups of 6 then re connect them to 6 pin this why you can run 3 s3's on it.

now don't believe it when bitmain say thy only take 355 w at the wall that is only if thy are way under clocked!!!! so most people end up pulling way too much power from there psu and killing it.

i use a 3000w platinum rated server power suppl
so i have the cleanest power i can get.

the best power at the wall i have gotten is
s3 384w
s3+ 390w
this is all at stock clocking s3+ use more power

also if you have s3+ batch 11 the program is screwed up and hash rate drops to nothing and the power is ether not set or is set way too high and you will need to ere flash back to the first 3 s3+ programs offered from bitmain but if you do that make sure you un check the saved settings box or it can crash and be un bootable

i have 26 s3's and my s3' were crashing many times a day thy were working good and then crash down to 40 gh/s i have been working on this problem for a month and finely fixed them.
if you had flashed bitmains last firmware December that's the problem and reset wont work and if you flash back to earlier program it crashes the miner and is un bootable.
i am willing to enplane step by step how to recover the unbootable miner and flash crashing miners back to good firmware with success. bitmain is making tones of btc telling people the control boards are bad just like thy told me and i fixed it. it took me three hrs to set up and figure it out and now that im setup it only takes 15 minuts to fix a crashed s3's.
if you want the help i can give it and in return it would be nice to get a btc donation for saving you tons of time and money

Well like i said i fixed the firmware on the dead one that crashed from bad firmware with ttfp server program threw serial converter wiping the program and re installing new firmware.

i still had quite a few running with the bad firmware on them, so after bench testing 1 a few times i found out how to take the program back without crashing the miner.
i successfully took all the others with bad firmware back to the first s3+ firmware!

The trick to go back from the bad firmware  is to first make sure your at the stock clock speed then reboot then go to flash firmware  (un check Save settings)!! then load the proper file then complete flash.

If you don't set stock clock and uncheck save settings it will not recover from the flash.

Once it reboots you can get the next 2 firmware updates in order one at a time don't skip an update each update must be flashed.
this will take it back to ip .99 and then you set your mining and save , then pick your clock speed and save, then go to networks change your ip to what you want and save, then when all is done reboot the miner.

for s3
flash all 3 one at a time tell you get done.
make sure you uncheck the save settings box before each flash or it will crash
antMiner_S320140711.bin
antMiner_S320140721.bin
antMiner_S320140811.bin
if you want the s3+ program on your s3 keep going down the list
s3+
flash all 3 one at a time tell you get done.
make sure you uncheck the save settings box before each flash or it will crash
antMiner_S320140826.bin
antMiner_S320141013.bin
antMiner_S320141024.bin
for good firmware stop at the first one 0826 or the third one 1024 if you stop at 1013 you will have problems but you still need to flash it to get to the 1024 program.

if you still have the December program on it it is probably is going crazy! to flash back don't forget to uncheck the save settings box or it may not be rotatable

then all will be good!!!!!!!!!!!!
please donate me some btc if this helped you out saving you tons of time and money!! 1P3WnGzCgWD9tFYrBKHReP1VoqRFF4fEXB

You have just been sent a personal message by dbm74 on Bitcoin Forum.

IMPORTANT: Remember, this is just a notification. Please do not reply to this email.

The message they sent you was:

i have 26 s3's and my s3' were crashing many times a day thy were working good and then crash down to 40 gh/s i have been working on this problem for a month and finely fixed them.
if you had flashed bitmains last firmware 1226 thats the problem and reset wont work and if you flash back to earlier program it crashes the miner and is un bootable.
i am willing to enplane step by step how to recover the unbootable miner and flash crashing miners back to good firmware with success. bitmain is making tones of btc telling people the control boards are bad just like thy told me and i fixed it. it took me three hrs to set up and figure it out and now that im setup it only takes 15 minuts to fix a crashed s3's.
if you want the help i can give it and in return it would be nice to get a btc donation for saving you tons of time and money

i have 26 s3's and my s3' were crashing many times a day thy were working good and then crash down to 40 gh/s i have been working on this problem for a month and finely fixed them.
if you had flashed bitmains last firmware 1226 thats the problem and reset wont work and if you flash back to earlier program it crashes the miner and is un bootable.
i am willing to enplane step by step how to recover the unbootable miner and flash crashing miners back to good firmware with success. bitmain is making tones of btc telling people the control boards are bad just like thy told me and i fixed it. it took me three hrs to set up and figure it out and now that im setup it only takes 15 minuts to fix a crashed s3's.
if you want the help i can give it and in return it would be nice to get a btc donation for saving you tons of time and money

i have 26 s3's and my s3' were crashing many times a day thy were working good and then crash down to 40 gh/s i have been working on this problem for a month and finely fixed them.
if you had flashed bitmains last firmware 1226 thats the problem and reset wont work and if you flash back to earlier program it crashes the miner and is un bootable.
i am willing to enplane step by step how to recover the unbootable miner and flash crashing miners back to good firmware with success. bitmain is making tones of btc telling people the control boards are bad just like thy told me and i fixed it. it took me three hrs to set up and figure it out and now that im setup it only takes 15 minuts to fix a crashed s3's.
if you want the help i can give it and in return it would be nice to get a btc donation for saving you tons of time and money

i am running 26 s3+ and just went threw all that it has been a pain! but i got them all fixed now! do you still need help???