 Show Posts
|
|
Pages: [1]
|
|
I tried Angry IP Scanner 3, and does not appear on the network as the two others do.
so I suppose I just try to reset it with a sd card.
*********************** Reset worked**************************
|
|
|
|
|
Hello
I just bought one more SP20 used (No. 3), but I can not come in contact with it.
I have taken psu and network cable from one of the other that works. but it does not appear on myminer.io.
fan running as it should, but after a few minutes flashes the green LED green.
PSU = 2x CX750
/Bruno
|
|
|
|
|
2.6.14
Uptime:2399 | FPGA ver:100 | BIST in 144
-----BOARD-0-----
PSU[UNKNOWN]: 0->(266w/266w)[266 266 266] (->266w[266 266 266]) (lim=280) 0c 407GH cooling:0/0xc8
-----BOARD-1-----
PSU[UNKNOWN]: 0->(258w/258w)[258 258 258] (->258w[258 258 258]) (lim=280) 0c 399GH cooling:0/0xc8
-----BOARD-2-----
PSU[UNKNOWN]: 0->(269w/269w)[269 269 269] (->269w[269 269 269]) (lim=280) 0c 409GH cooling:0/0xc8
-----BOARD-3-----
PSU[UNKNOWN]: 0->(249w/249w)[249 249 249] (->249w[249 249 249]) (lim=280) 0c 391GH cooling:0/0xc8
LOOP[0] ON TO:0 (w:227)
0: DC2DC/1/:[vlt1:734 vlt2:738(DCl:794 Tl:794 Ul:738) 105W 143A 53c] ASIC:[ 85c (125c) 1030hz(BL:1030) 111 (E:193) F:0 L:0]
1: DC2DC/1/:[vlt1:730 vlt2:738(DCl:794 Tl:794 Ul:738) 110W 149A 77c] ASIC:[ 85c (125c) 1080hz(BL:1080) 116 (E:193) F:0 L:0]
LOOP[1] ON TO:0 (w:216)
2: DC2DC/1/:[vlt1:734 vlt2:738(DCl:794 Tl:794 Ul:738) 111W 150A 83c] ASIC:[105c (125c) 1070hz(BL:1070) 110 (E:193) F:0 L:0]
3: DC2DC/1/:[vlt1:714 vlt2:719(DCl:794 Tl:719 Ul:738) 98W 136A 85c] ASIC:[120c (125c) 1000hz(BL:1000) 106 (E:193) F:0 L:0]
LOOP[2] ON TO:0 (w:229)
4: DC2DC/1/:[vlt1:734 vlt2:738(DCl:794 Tl:794 Ul:738) 108W 146A 55c] ASIC:[ 85c (125c) 1050hz(BL:1050) 117 (E:193) F:0 L:0]
5: DC2DC/1/:[vlt1:734 vlt2:738(DCl:794 Tl:794 Ul:738) 110W 149A 73c] ASIC:[ 85c (125c) 1070hz(BL:1070) 112 (E:193) F:0 L:0]
LOOP[3] ON TO:0 (w:190)
6: DC2DC/1/:[vlt1:722 vlt2:727(DCl:794 Tl:727 Ul:738) 99W 136A 78c] ASIC:[120c (125c) 980hz(BL: 980) 97 (E:193) F:0 L:0]
7: DC2DC/1/:[vlt1:703 vlt2:709(DCl:794 Tl:709 Ul:738) 102W 144A 92c] ASIC:[120c (125c) 1050hz(BL:1050) 93 (E:193) F:0 L:0]
[H:HW:1607Gh (500),DC-W:845,L:0,A:8,MMtmp:0 TMP:(15/15)=>=>=>(66/66 , 69/69)]
Pushed 11 jobs , in HW queue 4 jobs (sw:0, hw:0)!
min:55 wins:862[this/last min:24/20] bist-fail:248, hw-err:0
leading-zeroes:42 idle promils[s/m]:0/0, rate:1398gh/s asic-count:328 (wins:9+15)
wall watts:1143
Fan:90, conseq:200
AC2DC BAD: 0 0
R/NR: 1607/0
RTF asics: 0
FET: 0:9 1:9
0 restarted 0 reset 0 reset2 0 fake_wins
0 stuck_bist 0 low_power 0 stuck_pll 0 runtime_dsble
0 purge_queue 0 read_timeouts 0 dc2dc_i2c 0 read_tmout2 0 read_crptn
0 purge_queue3 0 bad_idle
0 err_murata
Adapter queues: rsp=1, req=24
|
|
|
|
|
is this to high?
Temp Front / Back T,B
15 °C / 67,72 °C
or what is the max?
|
|
|
|
|
Hi
i got a Sp20 running of 2 corsair cx850.
I got free power, and was wondering if it's possible to get i to run higere then 1610ghs by adjusting the volt setup.
the setup is:
Temp Front / Back T,B
15 °C / 67,72 °C
Fan Speed
Auto
Start Voltage
0.67 / 0.67 / 0.67 / 0.67
Max Voltage
0.74
Max Watts
280 / 280 / 280 / 280
Is there a guide to adjust so that it is running faster?
Thx.
|
|
|
|
|
