This is a scam, nothing else. They think it's OK and serious when they give a month to move coins, for example? Who is still receiving tweets in today's crazy age? In addition, on a tweet somewhere where nothing happens for a long time. The coin holder may be ill mainly at this time. And then like me, will he lose all the coins?
This is a scam, nothing else. Do they think that with this brand of coins, people will believe? Hardly. And I and others will take care of that too!
I mined this amount for several years. I only move to well-known coins, albeit with a lower yield. I ignore these shitcoins from now on.
Musicoin = scam!

I'm reading it here now. I had 2,200,000 Musicoin coins there. Irretrievably lost. It never occurred to me to watch their news every month. Especially when nothing has happened with this shitcoin for a long time. Great!

I'm looking for a modified firmware for S9 Hydro (4x Hashboard) with AsicBoost. Preferably something similar to the modified fw for S9, which allows chip tuning.
But I don't see anything on the S9 Hydro. Theoretically, the fw for S9 Hydro could be derived from the firmware for T9 + which has similar connectors and I tried it. It's OK, but I can only use 3 Hashboards.
Thank you for your reply or for the link, recommendation ...

I have a DR3 and unfortunately I didn't know about it. In good faith, I (although there was no reason) upgraded to the November fw. It is functional, but does not allow to reduce the fan speed. I will never give a new bitman's shit fw for no reason.
Is there any new solution to get older fw into DR3? Or via SD card? It never worked for me on another Antminer. In addition, there are no jumpers on the DR3 control board for switching to the SD card, and I didn't find anything about that on the net.
Thank you!

Of course my E3 also does not mined ETC. But, when I still mined GPU 380 2GB so 2 (??) years ago, so after a change in the epoch when the 2GB GPU was not enough. But it was enough to swap only one for 4GB in the rig, the others was just 2GB, and the whole rig was mined at full power for ETC. Unfortunately, it is probably not possible to do some trick in E3....

And I think that even though there is 4GB of memory per module in E3, maybe it uses a bit of memory outside and that's why the problem is now when the DAG ETC is 3,57GB. This is similar to having a 4GB Flashdisk and using only 95% max.

I would like to connect Antminer S1 to cksolo. What is the probability of mining a BTC block with 200GHs? I tried to count it, but I'm not sure of the result. I would like to compare it with the probability of some lottery in our country. Do you know anyone how to calculate it correctly? Thanks.

Big thanks! I confirm it works. Now Musicoin works on MEW and MyCrypto. I tried Trezor One and also Ledger X. Everything OK!

MEW and MyCrypto wallets report a "0" balance, although the correct balance can be seen in the explorer. Apparently there is a problem in the expiration of the SSL Musicoin node. What wallet do you use for Musicoin? Thank you.

9,182,025.45 RIC

https://chainz.cryptoid.info/ric/#!wallets

Poloniex - biggest balance

Yes it is written correctly. But I have 0.008 Dash unpaid, and I do not know if it will be reset until Dash is available.
I switched to BTC and still unpaid. It's been a few days, I have 0.002 BTC and I can not find info on the minimum payout. Thank you, if anyone knows.
Dash I'm now mining from Antpool, but I have outages.

ZPOOL now does not pay in DASH, but only in BTC!
I need a DASH payout.

Thanks a lot, it's OK. I wrote a + x. The webtranslator has a space between a + x. With the spaces it does not work. That was the mistake :-)

https://imgur.com/a/ZaWxu2O

Hello
is it possible that my version of L3 + (12/2017) does not work?
Or am I doing something wrong?
Thanks for reply or advice

P.S.
ssh login and commands after restarting L3 +
I tried everything possible and still the same.

The same with me for two D3. Here's the red LED and high fan speeds. Then the D3 itself restarts and again mining. What with this?

Hi guys,

Does anyone know of you in detail the 2x LED function on hash boards? Some lights on before start mining S9 on and some are not. And for each piece S9 it's different.
And now I find that the light LED on the hash board, which lights after the next restart is off.

Bitmain has just recently (the current manual for the auto fw is not and probably it's all secret :-) replied that after switching on the LEDs indicate power supply hash plates. But this is not the case, because the CH8 LED is not light on some of the S9 pieces, and for another S9 piece, for example, LED on CH7 is off. All LEDs before S9 start up only on one of my S9 pieces.
I feel that the LEDs after switching on before the start indicates the max hash frequency of the board. Frequency hash boards of the automatic fw is different.

Then, when the S9 is mining, all the top LEDs on the hash boards light up and the lower LED is off.

Thank you for your experience.

Hi guys,

I have S9 bought in 03/2017 and the 7 hash board is turned off after switching on and does not blink the LED even at start or after.
Do you have any experience with this?
Several times she was dead after a restart but after resting (about 3 hours) or resetting to the factory setting it was OK again 1-2 months.
Now it does not help. PSU OK, control board OK, data cable for hash plate also 100% OK. Nothing was burned, it did not smell and it was visually OK.
Is there a hard reset, resetting error hash boards, etc?

Bitmain claims to send "the entire miner" for a warranty test and repair.
S9 purchased before October 1, 2016 - just send a faulty hash board.
S9 purchased after October 1, 2016 - send the entire miner. That's bad, I come up with all the performance (even good hash boards).

What are your experiences?
And what about the S9 post-warranty service (even those new after October 1, 2016) is also sent to the entire miner?

Thanks for all!

Hi guys,

question, perhaps more for programmers and all who went further in depth sw Antmineru S1. But I was wondering this for Antminery S3-S9.

It would be possible to reduce the maximum temperature set by the manufacturer at 80 degrees C?

In S3 and above this temperature limitation can be switched off only. But I needed it must reduce to 60 - 70 degrees C. In order not to overload.
Then I could turn off the fan and it would be quiet :-)
I have proved that S1 has cooled to 80 degrees C, it automatically goes again.
Then it would work as a thermostat. Yes, the production would be lower. But mostly silence. In the winter, it would be ideal for heating :-)

Hi guys,

question, perhaps more for programmers and all who went further in depth sw Antmineru S1. But I was wondering this for Antminery S3-S9.

It would be possible to reduce the maximum temperature set by the manufacturer at 80 degrees C?

In S3 and above this temperature limitation can be switched off only. But I needed it must reduce to 60 - 70 degrees C. In order not to overload.
Then I could turn off the fan and it would be quiet :-)
I have proved that S1 has cooled to 80 degrees C, it automatically goes again.
Then it would work as a thermostat. Yes, the production would be lower. But mostly silence. In the winter, it would be ideal for heating :-)

Hi,
Thanks for your feedback.
Our S3 + B11 should be able to regulate the voltage below the frequency of in the menu, but I can not. I do not know why.
I think it should work with fw 2014 10xx.

I have these fw:
2014 0711
2014 0721
2014 0811
2014 0826
2014 1013
2014 1216
2014 1219
2015 0109

I got extra 2014 1216
But I have no 2014 1024, and this would like to get. Can we exchanged them?

Thanks and have a nice day!

Hi,
I can not set the voltage chips. In the menu box for tension, but typing in any value after boot S3 + B11 unresponsive and I measured voltage of the chip voltmeter and there is still 0.760 V. Bitmain then somehow forbid editing tension in newer firmwares, right? You have what firmware and editing tension will really work?
The whole history of issued fw is available somewhere for download? Bitmain on site, some fw deleted and not available. Thank you for advice.