 Show Posts
|
|
Pages: [1] 2 »
|
Thanks received the airdrop. I should be able to mine on pool using my web wallet address, correct? Just want to confirm that there won't be any issues in getting payment from the pool to my web wallet.
That is correct, it should not be a problem to mine to the online web wallet address. |
|
|
|
B2B looks like a good coin and and active dev, I like it!  |
|
|
|
I have been mining all day in this pool http://chrc.blockbit.ch/ and I can see the payments have been done in the pool, but my wallet is empty and the daemon is synced... What could be wrong? Will I ever recive the coins I mined that have still not been showing up in my wallet? I did try both the GUI and CLI wallet, same for both, wallet is empty.  Payments are going out fine to all miners from http://chrc.blockbit.ch. We have also been paying out steadily in 1000 CHRC blocks every 60s (to avoid tx errors) and do not have any payment backlogs. Any issues please notify us on support@blockbit.ch or DM here. SwedishBTC please follow these steps: open your wallet go to "settings" then choose "Show seed" enter your wallet password as will be asking by a prompt copy and save passphrase (nmenomic) which are given to you "close wallet" form settings in the opening window, after have choosing your language, choose the second option "Restore wallet from ..." in the other opening window, paste or enter previously saved passphrase (nmenomic) give to your wallet a new name (or keep old name but old associated backup files need to be deleted first) go to next step and give to a new password (or keep the old one) then your wallet will be well updated and you must have good behavior now (expected balance, unlocked amount, ...) As soon as I click "settings" the GUI wallet hang, I created my wallet with the CLI wallet... I installed the GUI wallet on another PC and now I could open the settings and click the "Show Seed" and this tutorial you made is working after the wallet synced again  Thank you m8! |
|
|
|
I have been mining all day in this pool http://chrc.blockbit.ch/ and I can see the payments have been done in the pool, but my wallet is empty and the daemon is synced... What could be wrong? Will I ever recive the coins I mined that have still not been showing up in my wallet? I did try both the GUI and CLI wallet, same for both, wallet is empty. Payments are going out fine to all miners from http://chrc.blockbit.ch. We have also been paying out steadily in 1000 CHRC blocks every 60s (to avoid tx errors) and do not have any payment backlogs. Any issues please notify us on support@blockbit.ch or DM here. SwedishBTC please follow these steps: open your wallet go to "settings" then choose "Show seed" enter your wallet password as will be asking by a prompt copy and save passphrase (nmenomic) which are given to you "close wallet" form settings in the opening window, after have choosing your language, choose the second option "Restore wallet from ..." in the other opening window, paste or enter previously saved passphrase (nmenomic) give to your wallet a new name (or keep old name but old associated backup files need to be deleted first) go to next step and give to a new password (or keep the old one) then your wallet will be well updated and you must have good behavior now (expected balance, unlocked amount, ...) As soon as I click "settings" the GUI wallet hang, I created my wallet with the CLI wallet... |
|
|
|
I have been mining all day in this pool http://chrc.blockbit.ch/ and I can see the payments have been done in the pool, but my wallet is empty and the daemon is synced... What could be wrong? Will I ever recive the coins I mined that have still not been showing up in my wallet? I did try both the GUI and CLI wallet, same for both, wallet is empty. |
|
|
|
|
Can you use your GPU to mine this coin?
|
|
|
|
To let ppl know, i am receiving weird message from newbies who are trying to get me to click a link,
Do not respond to the newbies & do not click the links.
That is all
I belive you are refering to me as the newbie with the link... I was just asking the current bidders if they might be intrested in buying the older Denarium coins from 2016 (Loaded, Empty & Auction) coins. And the link is just a link to an image with proof of the coins. |
|
|
|
Some people seems like they dont understand how to bid... Why not just bid +0.01 BTC from the cheapest coin? |
|
|
|
It is better if you raise 0.01 each time instead of 0.1... You never know if the BTC is sky high when the auction ends. Advice: Wait with placing a bet until the last day  |
|
|
|
|
BE AWARE!!!
A user named Technomage- is trying to scam the winners by sending a message with an address where he want you to pay the auction!
|
|
|
|
|
zcashgpuclient_silentarmy.exe crashes right after start on my Windows 10 64-bit, got 5x RX480 with latest drivers. Does anyone know how I can get this working to get up to 45 sol/s from each card?
|
|
|
|
|
This is still running on a test network, or can you mine real zCash already?
|
|
|
|
|
I have a question about the new version 7.2 and LBRY dual mining. Before I was using an older version of Claymore's Dual miner and mined ETH + DCR with my RX 480 and was running 27.3 MH/s on Ethereum, but after I updated to the v7.2 and started to mine Ethereum + LBRY I only get about 24.4 MH/s on Ethereum mining on the same settings, is this normal when mining LBRY instead of DCR?
|
|
|
|
I am having a problem with one of my rigs it is crashing all the time (sometimes I have to disconnect the power to all GPUs, uninstall the onboard graphics, and then connect the power to all cards again before rebooting the PC to get the PC to boot, and sometimes I even get THREAD_STUCK_IN_DEVICE_DRIVER error message when trying to boot the PC), and I did find out that if I turn off GPU 5 it seems to work better and not crashing.
I am running in Windows 10 x64 with Sappire Radeon RX 480, and I did try different drivers without any luck. And I got the same clock settings on all cards (I am running 4 more RX480 on another machine and that one did not crash one single time in over 3 weeks) This is how the logfile looks right before the crash if I run with GPU 5 on...
02:27:22:161 11f0 ETH: GPU0 27.335 Mh/s, GPU1 27.361 Mh/s, GPU2 27.348 Mh/s, GPU3 27.288 Mh/s, GPU4 27.351 Mh/s, GPU5 0.000 Mh/s
02:27:22:166 11f0 DCR - Total Speed: 2733.663 Mh/s, Total Shares: 319, Rejected: 4
02:27:22:171 11f0 DCR: GPU0 546.709 Mh/s, GPU1 547.214 Mh/s, GPU2 546.966 Mh/s, GPU3 545.762 Mh/s, GPU4 547.012 Mh/s, GPU5 0.000 Mh/s
02:27:22:446 ca0 DCR: weak share, skip
02:27:23:291 6ac DCR: weak share, skip
02:27:23:761 408 GPU0 t=59C fan=44%, GPU1 t=84C fan=61%, GPU2 t=79C fan=53%, GPU3 t=79C fan=58%, GPU4 t=85C fan=61%, GPU5 t=85C fan=60%
02:27:23:766 408 em hbt: 0, dm hbt: 0, fm hbt: 0,
02:27:23:766 408 watchdog - thread 0, hb time 203
02:27:23:771 408 watchdog - thread 1, hb time 94
02:27:23:771 408 watchdog - thread 2, hb time 0
02:27:23:771 408 watchdog - thread 3, hb time 125
02:27:23:776 408 watchdog - thread 4, hb time 31
02:27:23:776 408 watchdog - thread 5, hb time 141
02:27:23:781 408 watchdog - thread 6, hb time 219
02:27:23:781 408 watchdog - thread 7, hb time 110
02:27:23:786 408 watchdog - thread 8, hb time 94
02:27:23:786 408 watchdog - thread 9, hb time 203
02:27:23:791 408 watchdog - thread 10, hb time 77656
02:27:23:791 408 WATCHDOG: GPU 5 hangs in OpenCL call, exit
02:27:23:796 408 watchdog - thread 11, hb time 77547
02:27:23:801 408 WATCHDOG: GPU 5 hangs in OpenCL call, exit
02:27:24:806 408 Restarting OK, exit...
This is how my *.bat file looks
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool eth-eu.dwarfpool.com:8008 -ewal 0xMyEtherWalletAddress -epsw x -eworker miner2 -dpool stratum+tcp://dcr.coinmine.pl:2222 -dwal MyUsername.miner2 -dpsw MyPassword -dcri 40
What can be wrong, any advice?
Try not to push your GPU5 too hard... you must be running at 2250mhz solutions for you: 1. Find out which one is GPU5 2. back to stock setting and slowly work your way up (2100 or 2125 mem is a good start.. ) 2. Try ramp up the Fan speed (I saw your temp very high 85C) 3. Continue monitoring ok, I will try to reset that card, any advice what voltage settings I should have? If this not solve it I will change raiser and see if it works better with another. I am running at 2200mhz memory @ 940mV, and 1100 core clock @ 950mV. I am running the same setting for all cards. I have fan speed max set to 3200 (I dont really understand WattMan's fan settings??), can I make the fan always go on 70% speed? Because the noice is not a problem. I did try run without even clocking the cards, I still get the same error message on GPU 5 after some time mining... Is this card "broken"? |
|
|
|
I am having a problem with one of my rigs it is crashing all the time (sometimes I have to disconnect the power to all GPUs, uninstall the onboard graphics, and then connect the power to all cards again before rebooting the PC to get the PC to boot, and sometimes I even get THREAD_STUCK_IN_DEVICE_DRIVER error message when trying to boot the PC), and I did find out that if I turn off GPU 5 it seems to work better and not crashing.
I am running in Windows 10 x64 with Sappire Radeon RX 480, and I did try different drivers without any luck. And I got the same clock settings on all cards (I am running 4 more RX480 on another machine and that one did not crash one single time in over 3 weeks) This is how the logfile looks right before the crash if I run with GPU 5 on...
02:27:22:161 11f0 ETH: GPU0 27.335 Mh/s, GPU1 27.361 Mh/s, GPU2 27.348 Mh/s, GPU3 27.288 Mh/s, GPU4 27.351 Mh/s, GPU5 0.000 Mh/s
02:27:22:166 11f0 DCR - Total Speed: 2733.663 Mh/s, Total Shares: 319, Rejected: 4
02:27:22:171 11f0 DCR: GPU0 546.709 Mh/s, GPU1 547.214 Mh/s, GPU2 546.966 Mh/s, GPU3 545.762 Mh/s, GPU4 547.012 Mh/s, GPU5 0.000 Mh/s
02:27:22:446 ca0 DCR: weak share, skip
02:27:23:291 6ac DCR: weak share, skip
02:27:23:761 408 GPU0 t=59C fan=44%, GPU1 t=84C fan=61%, GPU2 t=79C fan=53%, GPU3 t=79C fan=58%, GPU4 t=85C fan=61%, GPU5 t=85C fan=60%
02:27:23:766 408 em hbt: 0, dm hbt: 0, fm hbt: 0,
02:27:23:766 408 watchdog - thread 0, hb time 203
02:27:23:771 408 watchdog - thread 1, hb time 94
02:27:23:771 408 watchdog - thread 2, hb time 0
02:27:23:771 408 watchdog - thread 3, hb time 125
02:27:23:776 408 watchdog - thread 4, hb time 31
02:27:23:776 408 watchdog - thread 5, hb time 141
02:27:23:781 408 watchdog - thread 6, hb time 219
02:27:23:781 408 watchdog - thread 7, hb time 110
02:27:23:786 408 watchdog - thread 8, hb time 94
02:27:23:786 408 watchdog - thread 9, hb time 203
02:27:23:791 408 watchdog - thread 10, hb time 77656
02:27:23:791 408 WATCHDOG: GPU 5 hangs in OpenCL call, exit
02:27:23:796 408 watchdog - thread 11, hb time 77547
02:27:23:801 408 WATCHDOG: GPU 5 hangs in OpenCL call, exit
02:27:24:806 408 Restarting OK, exit...
This is how my *.bat file looks
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool eth-eu.dwarfpool.com:8008 -ewal 0xMyEtherWalletAddress -epsw x -eworker miner2 -dpool stratum+tcp://dcr.coinmine.pl:2222 -dwal MyUsername.miner2 -dpsw MyPassword -dcri 40
What can be wrong, any advice?
Try not to push your GPU5 too hard... you must be running at 2250mhz solutions for you: 1. Find out which one is GPU5 2. back to stock setting and slowly work your way up (2100 or 2125 mem is a good start.. ) 2. Try ramp up the Fan speed (I saw your temp very high 85C) 3. Continue monitoring ok, I will try to reset that card, any advice what voltage settings I should have? If this not solve it I will change raiser and see if it works better with another. I am running at 2200mhz memory @ 940mV, and 1100 core clock @ 950mV. I am running the same setting for all cards. I have fan speed max set to 3200 (I dont really understand WattMan's fan settings??), can I make the fan always go on 70% speed? Because the noice is not a problem. |
|
|
|
|
I am having a problem with one of my rigs it is crashing all the time (sometimes I have to disconnect the power to all GPUs, uninstall the onboard graphics, and then connect the power to all cards again before rebooting the PC to get the PC to boot, and sometimes I even get THREAD_STUCK_IN_DEVICE_DRIVER error message when trying to boot the PC), and I did find out that if I turn off GPU 5 it seems to work better and not crashing.
I am running in Windows 10 x64 with Sappire Radeon RX 480, and I did try different drivers without any luck. And I got the same clock settings on all cards (I am running 4 more RX480 on another machine and that one did not crash one single time in over 3 weeks) This is how the logfile looks right before the crash if I run with GPU 5 on...
02:27:22:161 11f0 ETH: GPU0 27.335 Mh/s, GPU1 27.361 Mh/s, GPU2 27.348 Mh/s, GPU3 27.288 Mh/s, GPU4 27.351 Mh/s, GPU5 0.000 Mh/s
02:27:22:166 11f0 DCR - Total Speed: 2733.663 Mh/s, Total Shares: 319, Rejected: 4
02:27:22:171 11f0 DCR: GPU0 546.709 Mh/s, GPU1 547.214 Mh/s, GPU2 546.966 Mh/s, GPU3 545.762 Mh/s, GPU4 547.012 Mh/s, GPU5 0.000 Mh/s
02:27:22:446 ca0 DCR: weak share, skip
02:27:23:291 6ac DCR: weak share, skip
02:27:23:761 408 GPU0 t=59C fan=44%, GPU1 t=84C fan=61%, GPU2 t=79C fan=53%, GPU3 t=79C fan=58%, GPU4 t=85C fan=61%, GPU5 t=85C fan=60%
02:27:23:766 408 em hbt: 0, dm hbt: 0, fm hbt: 0,
02:27:23:766 408 watchdog - thread 0, hb time 203
02:27:23:771 408 watchdog - thread 1, hb time 94
02:27:23:771 408 watchdog - thread 2, hb time 0
02:27:23:771 408 watchdog - thread 3, hb time 125
02:27:23:776 408 watchdog - thread 4, hb time 31
02:27:23:776 408 watchdog - thread 5, hb time 141
02:27:23:781 408 watchdog - thread 6, hb time 219
02:27:23:781 408 watchdog - thread 7, hb time 110
02:27:23:786 408 watchdog - thread 8, hb time 94
02:27:23:786 408 watchdog - thread 9, hb time 203
02:27:23:791 408 watchdog - thread 10, hb time 77656
02:27:23:791 408 WATCHDOG: GPU 5 hangs in OpenCL call, exit
02:27:23:796 408 watchdog - thread 11, hb time 77547
02:27:23:801 408 WATCHDOG: GPU 5 hangs in OpenCL call, exit
02:27:24:806 408 Restarting OK, exit...
This is how my *.bat file looks
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool eth-eu.dwarfpool.com:8008 -ewal 0xMyEtherWalletAddress -epsw x -eworker miner2 -dpool stratum+tcp://dcr.coinmine.pl:2222 -dwal MyUsername.miner2 -dpsw MyPassword -dcri 40
What can be wrong, any advice?
|
|
|
|
|
I am currently running 10x Sapphire Radeon RX 480 at 27.3MH/s ETH and 550MH/s DCR each without any problem, my only problem is that I would like to solomine DCR, is it possible to solomine DCR with this software? Or do I have to mine in a pool?
|
|
|
|
I am running 3x Sapphire RX 480 8GB, all very stable at 27.3 MH/s each ETH & 546 MH/s DCR ~153w @ each card and temperature is 77C each card.  I will try get a bit more out of them, but this setting have been running without any problem for 4 days straight now. (Switched pool about 3 hours ago) I am running them at 1100 Core clock and 2200 Memory clock, Windows 10, Crimson 16.7.1. Does anyone know how many H/s you get from each card on Cryptonight mining with this RX 480 Cards? And what software and settings do you have? |
|
|
|
|
