 Show Posts
|
|
Pages: [1] 2 »
|
|
Is there anything happenning with the pool now? My miners are still running with the same speed but get much less earnings amount for 8 hours than usual. Please help.
|
|
|
|
I have 2 payouts being late. One is late for over a day, another is 6 hours. I checked the transaction, but both are unconfirmed. Usually, it takes about 1 hour to get through, those 2 of my payouts are longer than usual. Is that normal?
https://blockchain.info/unconfirmed-transactionsSo, that means, all the transaction will go through lately? I'm new to the pool, so, I dont really know how a multi-pool works or payout. there is a growing global queue of BTC transactions. All you can do it wait, and have a coffee. The BTC was sent from the pool and now waits. Thank you for your clarification, it helps a lot. I appreciate it. |
|
|
|
Sorry if this is out there but I couldn't find it.
What is the best way to set the miner NOT to mine a coin?
I found out that I can do that by not selecting the algorithm of that coin, but I don't wanna miss other coins of the same algor.
I just want the miner not to mine just that one coin, not the whole algo.
Please help, or link me to the old topic of this.
I appreciate your help.
I'm assuming you are using a profit miner? If so, which one? If you want to exclude a certain coin on an algo, then you will have to setup a pool for every coin you want to mine at that site, and put them in a pool group. It's a lot of work, if there's a few dozen coins in that algo. But... if you are using a profit miner, then you are generally at the mercy of what the multi-algo pool says is most profitable. I know that some pools like zpool can switch you to non-profitable coins in order to keep performance up, or to reach a minimum amount of coins so that they can send it to an exchange. Can't we just go in to Options then Algorithms and uncheck the ones we don't want? That's what I was mentioning. It's not about the algo, it's about the one coin in that algo. Let's say in Equilhash, u just want to mine Zencash, not zcash, how do u exclude zcash? |
|
|
|
Sorry if this is out there but I couldn't find it.
What is the best way to set the miner NOT to mine a coin?
I found out that I can do that by not selecting the algorithm of that coin, but I don't wanna miss other coins of the same algor.
I just want the miner not to mine just that one coin, not the whole algo.
Please help, or link me to the old topic of this.
I appreciate your help.
I'm assuming you are using a profit miner? If so, which one? If you want to exclude a certain coin on an algo, then you will have to setup a pool for every coin you want to mine at that site, and put them in a pool group. It's a lot of work, if there's a few dozen coins in that algo. But... if you are using a profit miner, then you are generally at the mercy of what the multi-algo pool says is most profitable. I know that some pools like zpool can switch you to non-profitable coins in order to keep performance up, or to reach a minimum amount of coins so that they can send it to an exchange. Can't we just go in to Options then Algorithms and uncheck the ones we don't want? That's what I was mentioning. It's not about the algo, it's about the one coin in that algo. Let's say in Equilhash, u just want to mine Zencash, not zcash, how do u exclude zcash? |
|
|
|
|
Sorry if this is out there but I couldn't find it.
What is the best way to set the miner NOT to mine a coin?
I found out that I can do that by not selecting the algorithm of that coin, but I don't wanna miss other coins of the same algor.
I just want the miner not to mine just that one coin, not the whole algo.
Please help, or link me to the old topic of this.
I appreciate your help.
|
|
|
|
I switched to Awesome Miner, but I am prepared to give WinMiner another go if that doesn't work out.
Would you please review your income profit in Awesome Miner? |
|
|
|
Well it appears to me like they worked out whatever the numbers issue was. Well done WinMiner Team. I finally made what I feel what would be inline with my 5 rigs production pocketing a 55 bucks in under a 24 hour period. Not sure about if I'll ever see what I earned the 3 days before but to me it seems as if the system is now recording numbers correctly. Happy Happy Joy Joy!!!  Totally AGREE!! They got themselves back together, and so do I. |
|
|
|
Well I left and went with MegaMiner setup to use both miningpoolhub and zpool.ca and went from making $12 per day (WinMiner) to $30 per day (MegaMiner) using my 5 RX 470's, 1 gtx 1080TI, 1 GTX 1080. Not going to look back. Either the pools they use are incompetent or they are thieves.
Can I have their website, please? |
|
|
|
Seems to be working well again now. Back to my normal $0.01 every 10 minutes. I just have to avoid VTC & ZEN.
Zen seems to be the highest paying right now. I am back to being opted in to all coins and the system seems to be stable today. Just hopeful the payout after 24 hours matches with what I would expect! Zclassic is paying highest right now for me at nearly 11$ per day but on winminer im getting 7.6$.This is theft of the highest order.Waste of my electricity and what a waste of a good sotware. You can check it every hour, to see if it matches with your expecting payout. |
|
|
|
Seems to be working well again now. Back to my normal $0.01 every 10 minutes. I just have to avoid VTC & ZEN.
Can anyone else confirm it, please? |
|
|
|
Yeah I must say that the numbers within the past 24 hours do not seem to be matching up very well for me either.
My 5 rigs are pushing anywhere from $45-$78 combined on the estimated "Live" earnings however my take home on the Statistic graph was only $32.54 for yesterday.
Hush, VTC and Zen seem to be working the best numbers wise for my GPUs and Sumo on the CPUs...
Oddly enough I did find one of my 8xGPU rigs was just at "idle" on the CPU and GPUs this morning. Stopped and started the WinMiner client again and it started right back up.. Not sure what that was about.
For me, it's been for a couple of days, like 3-4 days, I believe, since I found out there was a drastically decrease in my income, about 30%. No matter how high the supposed income was. |
|
|
|
Is there any delay in registering numbers under 'Statistics' page? The reported numbers seem very low considering the pace at which WinMiner is earning (under 'Live' page).
I agree, there is a delay now in updating the income, I wonder what is happening. I can give an example for this. Let's say I can make it like 5USD/hr. Before, WM will update every hour, and it added up 5USD/hr for me, but now, like, at 10am, my wallet has 5USD. 11am, nothing happens. 11:30, it ticks up to 10USD. Then, it will do like that for the next hours. That means, every hour, we lose some bucks, added up for a whole day, that could be a big money. Usually I will believe there is a decrease/increase of income, but I also made a log to update from my computer for every hour, and did some math, and I found out that I lost almost 30% of my income. Where did all those bucks go?  ?? I am ok if you said that you are having tons of things to do to scale up, but will my fund be back later then? At least, please clarify everything to us users. I used WM for a long time, and I love it. But this time is out of line, I really need some explanation for this. |
|
|
|
|
Are they doing ok now?
First, yesterday I got an update from them, but miner stopped working, not auto reset like usual.
Today, the website does not update my income in their wallet for a long time (usually it will update every hour), I wonder if there is anything happen to them.
|
|
|
|
I got a question, this could be noob, but I am confused a lil now.
The fee is 3%, but when I withdrew 400 usd from my account, and the amount comes to my btc wallet or paypal is around 370. That means 30 usd had been deducted, which is 8~9% deduction. Is that normal?
i think paypal have higher fees than normal withdraws I mean, even I withdraw my money into a BTC wallet, it deducted the same amount. |
|
|
|
|
I got a question, this could be noob, but I am confused a lil now.
The fee is 3%, but when I withdrew 400 usd from my account, and the amount comes to my btc wallet or paypal is around 370. That means 30 usd had been deducted, which is 8~9% deduction. Is that normal?
|
|
|
|
|
Hi there,
I am a newbie in mining coin, so I tried to setup a rig myself, and here is my problem.
I am using Asrock H81 Pro BTC Mobo, 4GB RAM, and 6x Asus Rx 480 4GB.
I am using Claymore miner to mine Zcash, but I have a serious problem.
After a couple of secs running, one of 6 GPU will hang and watchdog will reset the rig. It says "OpenCL call, GPU 3 hangs, watchdog will reset"..
I tried so many solutions but no use.
I tried and replace all the Riser - no use.
I think because I didn't plug in 2 4 PIN power connector before, but now even I plug all the power connectors in, problem still exists.
I hope if anyone had this problem before or had experience about this, please help me.
|
|
|
|
hopely this will help you, if all your hardware don't have a problem from PSU,cable, and riser, instal the lastest driver ( in my experience for multiple GPU wait until finish all instal the driver), restart, and run MAB set default for all setting accept fan speed as you needed at your temp room, and then run claymore v.9.1. If still get hang try setting your intensity one by one from 5, 6,7 or 8.
I did all those steps, but no use. And yes, I have latest catalyst 16.11.2, I even low intensity to 4. May I ask about your hardware, like CPU, Mobo, PSU, RAM, and OS? I read from above that it need 80 bronze cert PSU, im not sure if that's the problem, or from my OS. Just my .02, but I believe the default intensity is 4. I could be wrong, but I have set -i 4 and my hashrate is same as default without setting intensity. Try backing it down to 1 or 2, then try to get up to 3 and see what runs stable. Also, suppose you have a 1000 watt bronze psu and 4 RX 480's running. 150 watts per card. They actually use much less, but that would be 600 watts. Then your cpu is maybe going to be pulling 100 max, and that's if it ever gets to any kind of load... You'd have lots of headroom. Unless you're trying to run a 6 card rig on 1000 watt psu lol. I have 2 x 750W PSU, each PSU runs 3 cards. I dont blame Claymore 9.0 or 9.1, I had this problem since the first time I use claymore, since 5.0. There will be 1 card always not working, will hash 0 H/s. After a certain of time, watchdog says that GPU hangs and reset. No matter how many GPU I use, there will be 1 not working. My temporary fix was keep rebooting until all GPUs working, but now that ways seems not work anymore. |
|
|
|
hopely this will help you, if all your hardware don't have a problem from PSU,cable, and riser, instal the lastest driver ( in my experience for multiple GPU wait until finish all instal the driver), restart, and run MAB set default for all setting accept fan speed as you needed at your temp room, and then run claymore v.9.1. If still get hang try setting your intensity one by one from 5, 6,7 or 8.
I did all those steps, but no use. And yes, I have latest catalyst 16.11.2, I even low intensity to 4. May I ask about your hardware, like CPU, Mobo, PSU, RAM, and OS? I read from above that it need 80 bronze cert PSU, im not sure if that's the problem, or from my OS. |
|
|
|
Hello guys,
I have a problem when mining. I am using Claymore miner and 6 RX 480 GPUs.
My problem is, there will be 1 GPU not recognized or something like that.
Let's make an example like: when I have 6 GPUs, GPU 3 will be mining at 0 H/s, and the console says: "GPU 3 hangs when OpenCL calls, exit".
when I have 5 GPUs, one of them will behave the same, which means, GPU x will be mining at 0 H/s, "GPU x hangs when OpenCL calls, exit".
I follow all the settings, put in necessary command lines, etc.
I used to reboot until my rig let all the GPUs work, but now that way is not working anymore.
Please help.
well there are various things to try/check.... first let us know what components you are using (mobo, ram, PSU, CPU, Win7/8/10) and what settings for the GPU (OC, voltage??) from the first shoot i would gues low virtual mem (have to be 16gb min.) or too much OC/undervolt ( as many wrote that this is the main problem by the "hanging" of the GPU).. I forgot about my components: Mobo: Biostar TB85 CPU: Intel Celeron G1840 2.8Ghz PSU: 2 x 750W OS: window 10 enterprise About paging memory, I first tried to set it up to 16GB, but now I set it to even 30~40GB, still no help, and I dont even OC it. well i would gues: 1, try to change the gpu 3 (the GPU which is hanging and loosing the hash rate to 0h/s) to the main port and plug the monitor to it, or use an dummy plug... 2, bad GPU riser (hope you are powering the risers with the molex directly to the PSU, the sata cables are dangerous and it doesnt deliver enough power to the riser which could cause the hanging..) 3, something wrong with the GPU... I would try to set up the rig with 1 gpu, if it works then add next one and try with 2 GPUs, if it works then add next one and try it with 3 until you find out which one is causing the problem.. It will take some time, but this way you can see with how much GPUs max is your rig running normal, where is the limit...) 4, dont know the mobo - so maybee it is not able to handle 6 GPUs (really dont know, try to search if some1 experienced to get it work, the mobo, with 6 gpus) dont have any amd RX, but check also here on forum what driver to use, as im using the 15.12 driver but this one is not the right one for the RX GPUs... Hope it helps.... GL Thank you for your advice, Anything related to physical touch up, like, try another riser, switch GPU, plug 1 by 1, etc, I tried them all. About GPU, I dont think that the GPU problem. You know, it's not about GPU 3 or the power, my case is like I described before When I plug 6 GPUs in, GPU 3 will hang. When I plug 5 GPUs in, GPU x will hang. There will be always 1 GPU hanging, no matter how many GPUs I plug in. always same port? maybee the port on the mobo is bad... (if it is the same port..) No, when I have 5 GPUs in, that means I take that GPU 3 out, just left 5 on the rig, at that time, another GPU will hang. ok i did a small research, obviusly you are not the only one with this problem. Most ppl had the problem when it was OC, but you said you are using stock settings.... Next if the GPU hangs is there any change in the device manager? Are all 6 GPUs recognized by the system and device manager? Also did you tryied the 6 gpu setting, and after it hangs put a dummy or a monitor to the "hanged" gpu? does it changed after miner restart? Yes, Im using stock settings, Device manager show all 6 GPUs are recognized. eh, about the tried 6 GPus setting, put dummy or a monitor things, I dont have those kind of things to monitor GPU. Im using MSI afterburner to take care of fan speed, but I thought mb it is the reason, I tried to turn off the Afterburner, but no help. |
|
|
|
Hello guys,
I have a problem when mining. I am using Claymore miner and 6 RX 480 GPUs.
My problem is, there will be 1 GPU not recognized or something like that.
Let's make an example like: when I have 6 GPUs, GPU 3 will be mining at 0 H/s, and the console says: "GPU 3 hangs when OpenCL calls, exit".
when I have 5 GPUs, one of them will behave the same, which means, GPU x will be mining at 0 H/s, "GPU x hangs when OpenCL calls, exit".
I follow all the settings, put in necessary command lines, etc.
I used to reboot until my rig let all the GPUs work, but now that way is not working anymore.
Please help.
well there are various things to try/check.... first let us know what components you are using (mobo, ram, PSU, CPU, Win7/8/10) and what settings for the GPU (OC, voltage??) from the first shoot i would gues low virtual mem (have to be 16gb min.) or too much OC/undervolt ( as many wrote that this is the main problem by the "hanging" of the GPU).. I forgot about my components: Mobo: Biostar TB85 CPU: Intel Celeron G1840 2.8Ghz PSU: 2 x 750W OS: window 10 enterprise About paging memory, I first tried to set it up to 16GB, but now I set it to even 30~40GB, still no help, and I dont even OC it. well i would gues: 1, try to change the gpu 3 (the GPU which is hanging and loosing the hash rate to 0h/s) to the main port and plug the monitor to it, or use an dummy plug... 2, bad GPU riser (hope you are powering the risers with the molex directly to the PSU, the sata cables are dangerous and it doesnt deliver enough power to the riser which could cause the hanging..) 3, something wrong with the GPU... I would try to set up the rig with 1 gpu, if it works then add next one and try with 2 GPUs, if it works then add next one and try it with 3 until you find out which one is causing the problem.. It will take some time, but this way you can see with how much GPUs max is your rig running normal, where is the limit...) 4, dont know the mobo - so maybee it is not able to handle 6 GPUs (really dont know, try to search if some1 experienced to get it work, the mobo, with 6 gpus) dont have any amd RX, but check also here on forum what driver to use, as im using the 15.12 driver but this one is not the right one for the RX GPUs... Hope it helps.... GL Thank you for your advice, Anything related to physical touch up, like, try another riser, switch GPU, plug 1 by 1, etc, I tried them all. About GPU, I dont think that the GPU problem. You know, it's not about GPU 3 or the power, my case is like I described before When I plug 6 GPUs in, GPU 3 will hang. When I plug 5 GPUs in, GPU x will hang. There will be always 1 GPU hanging, no matter how many GPUs I plug in. always same port? maybee the port on the mobo is bad... (if it is the same port..) No, when I have 5 GPUs in, that means I take that GPU 3 out, just left 5 on the rig, at that time, another GPU will hang. |
|
|
|
|
