 Show Posts
|
|
Pages: [1] 2 »
|
|
Como estan? Hace meses logre vender mis btc en Coinsbank y logre hacer la transferencia bancaria desde mi Usd wallet a mi cuenta en el mercantilbank en Usa. Sin embargo trate de hacer lo mismo ahorita y no están haciendo transferencias bancarias, que me recomiendan? Necesito unos dolares y quiero vender mis btc.
|
|
|
|
The first thing I would do is the basic troubleshooting if you have not. Swap the ports on the controller, try the bad boards cable into a port where one of the known working boards was. Confirm it still doesnt hash that way. If that is the case your only option really is bitmainwarranty. I know they do a lot of russian repairs and whatnot so I dont think they would have a problem working with an international customer.
Thank you so much man, I'll do that!... Is it often these boards have the same problem? Or It was because of the temperatures or high voltage or may be bad luck? |
|
|
|
What help are you looking to get? A bad board is a bad board. If you have gone though the basic troubleshooting and its still not working the only option you have is a paid repair service.
I wanted to know if it was a bad board... So what do you suggest me man? I do not know where to send it... Somebody told me about bitmainwarranty but I'm trying to contact them and I do not receive any anwer... Is there any website where I could buy that board or a place where I could send it? Thank you so much for your answer Fanatic26 |
|
|
|
Hello guys, I know this is not the best place to post this problem, but as I know you are the best and smartest guys over here please help me with this if you are able: I've been mining in kano since six months I think and from yesterday I realized my TH/S dropped a lot and I went to check my miners and I found this: I have an Antminer S9 and it got in the chain #8 GH/S(RT) = 0.00000 I've seen in the forum some problems about that and says it is a board problem. My antminer is out of warranty, and I am not able to send back to bitmain to get a repair ticket because it is almost impossible to send it from my country. So please help me guys Sad I'm really worry about that Sad Here is a picture of what I'm telling you:  You need to post a screenshot of the full page for seeing all chips. but it looks like you have a problem with 1 hashing board; should send to bitmain for repair or purchase a hashing board and replace it at your own risk. I also highly recommend to have a 2nd and 3rd mining address for backup (not just the 1st one). Hello Apprentice I tried to put the screenshot but I do not know why it does not appear I clicked on "Insert Image" then I put the address, lets see if it works... The board I must buy is the one is in the bitmain address? Do you guys have any guid how to do that? I hear good stories about http://bitmainwarranty.com. They are US-based, might save you a lot of delay and trouble going in and out of China. Have you tried taking the power off your S9 for some time, and then powering it up again (from the image it looks like that). Might help boot the board to life again. Do you think It could work? I did it today for a while but it just worked for a while then It turned off... I can't send this kind of products out of my country due to some regulations we do have here... thats why I'm worry about this. Do you know any solution about that? Where can I buy those hash board and Do it by myself? |
|
|
|
Hello guys, I know this is not the best place to post this problem, but as I know you are the best and smartest guys over here please help me with this if you are able: I've been mining in kano since six months I think and from yesterday I realized my TH/S dropped a lot and I went to check my miners and I found this: I have an Antminer S9 and it got in the chain #8 GH/S(RT) = 0.00000 I've seen in the forum some problems about that and says it is a board problem. My antminer is out of warranty, and I am not able to send back to bitmain to get a repair ticket because it is almost impossible to send it from my country. So please help me guys Sad I'm really worry about that Sad Here is a picture of what I'm telling you: You need to post a screenshot of the full page for seeing all chips. but it looks like you have a problem with 1 hashing board; should send to bitmain for repair or purchase a hashing board and replace it at your own risk. I also highly recommend to have a 2nd and 3rd mining address for backup (not just the 1st one). Hello Apprentice I tried to put the screenshot but I do not know why it does not appear I clicked on "Insert Image" then I put the address, lets see if it works... The board I must buy is the one is in the bitmain address? Do you guys have any guid how to do that? |
|
|
|
So far I've had two miners like that, too.
First thing I'd try is take off the cable of the board and reattach.
I've also switched out boards with each other and reattached them. So far I've had luck and then they started working.
Hello @Scaary I have the same problem too but the different is mine shows temperature. Please let me know, how did you do to repair that? Do you have a guide? I'm not able to send the miner to bitmain so I have to do it by myself. Help me please   Here is a picture I took |
|
|
|
Hello guys, I know this is not the best place to post this problem, but as I know you are the best and smartest guys over here please help me with this if you are able: I've been mining in kano since six months I think and from yesterday I realized my TH/S dropped a lot and I went to check my miners and I found this: I have an Antminer S9 and it got in the chain #8 GH/S(RT) = 0.00000 I've seen in the forum some problems about that and says it is a board problem. My antminer is out of warranty, and I am not able to send back to bitmain to get a repair ticket because it is almost impossible to send it from my country. So please guys, help me. I'm really sad about that Here is a picture of what I'm telling you:  |
|
|
|
Hello Guys, first of all I realle need your help in this. I have an Antminer S9 and it got in the chain #8 GH/S(RT) = 0.00000 I've seen in the forum some problems about that and says it is a board problem. My antminer is out of warranty, and I am not able to send back to bitmain to get a repair ticket because it is almost impossible to send it from my country. So please help me guys I'm really worry about that Here is a picture of what I'm telling you: |
|
|
|
|
I really wanna thank you guys, all of you... I didn't know I could mine any coin with the L3+... Thank you so much really.
|
|
|
|
Hello guys, I'm new in Litecoin... I've purchased 2 Antminer L3+ 504mhz and I already got them. I'd like to know in which pool I must put them... Hopefully you can help me, thank you.
Nicehash or Prohash. Use a switching pool. you will maximize your bottom line. Is https://prohashing.com/ the Prohash pool website? |
|
|
|
Hello guys, I'm new in Litecoin... I've purchased 2 Antminer L3+ 504mhz and I already got them. I'd like to know in which pool I must put them... Hopefully you can help me, thank you.
Nicehash or Prohash. Use a switching pool. you will maximize your bottom line. Thank you man but what you mean when you say use a switching pool? A switching pool redirects your hashrate to mine the most profitable coin possible at any given point in time. But is it possible with an Antminer L3+  What about if I just want to mine litecoin? |
|
|
|
Hello guys, I'm new in Litecoin... I've purchased 2 Antminer L3+ 504mhz and I already got them. I'd like to know in which pool I must put them... Hopefully you can help me, thank you.
Nicehash or Prohash. Use a switching pool. you will maximize your bottom line. Thank you man but what you mean when you say use a switching pool? |
|
|
|
|
Hello guys, I'm new in Litecoin... I've purchased 2 Antminer L3+ 504mhz and I already got them. I'd like to know in which pool I must put them... Hopefully you can help me, thank you.
|
|
|
|
Rockou Yes that was the email address you got in every email from the pool  No don't post email addresses on public forums I'm so sorry Mr Kano, but I'm new in this so, it will not happen again... And thank you so much |
|
|
|
Hello Guys! Is anyone having problems to access to your account? Since today, I'm having this problem because it says login failed and I'm worry about to be hacked so please if anyone can help me I'd appreciate that.
I was able to login just fine. Done!!! I just loged in thank you! |
|
|
|
|
Hello Guys! Is anyone having problems to access to your account? Since today, I'm having this problem because it says login failed and I'm worry about to be hacked so please if anyone can help me I'd appreciate that.
|
|
|
|
Hi guys!! I just started mining in kano.is and It is just an awesome pool. Thank you Mr Kano!! I started loving the pool  |
|
|
|
|
Hi guys I know that this post is repeated everywhere but, I do not speak english very well and I need to be explained about this and What I should do to be safe!!! I downloaded a wallet software to deposit my btc but also I do not understand how it works... I use coinsbank as my personal wallet, what is your recommendation? Thank you!!
|
|
|
|
|
Thank you so much guys really!!
|
|
|
|
|
Guys!! Please help me on it!! I need your comments about this
|
|
|
|
|
