 Show Posts
|
|
Pages: [1] 2 »
|
since my Raspberry is already connected wireless to the internet is their a way to just get a ethernet splitter plug the splitter into my pi and connect my cubes via ethernet to the ethernet splitter on the pi and afterwards point the cubes to my pi's IP?
Are you talking about a switch or hub?? Am talking about the ethernet port on the raspberry pi. Sort of like using the raspberry pi as a router and plugging the cubes to the ethernet port on the pi. |
|
|
|
Hello everyone, So i am new to mining i'll start of with that.. I just purchased 2 cubes and need some help to set them up. Am used to just plug n play with usb since i had BFL products and never required doing extra work. I know i need a power supply thats strong enough to support both cubes on HIGH clock mode. Any recommendations? also i have a raspberri pi i would use before can i still put this to use in any way with my new cubes?
U can run 2 cubes on a Corsair TX850 PSU. Raspberry Pi works well. I use Minepeon. Just use the --http-port <port#> option in bfgminer and point your Cubes to the IP address/port # for the Pi. Should be a piece of cake. Would the corsair TX850 PSU support both cubes on the HIGH clock setting? If i can use the Raspberry Pi (already running Minepeon) do i connect both miners via usb or through the Ethernet port on the Pi. I currently have the Pi configured to run wirelessly off my wifi connection. The TX850 can run 2 at high clock rate. I have about dozen Cubes set up this way. Do not connect a USB cable to the Cube - the USB port on the Cube is not for mining. To run Cubes on Minepeon, make sure to point the Cube to the IP address of the Raspberry Pi by putting its IP address (usually 192.168.1.25) in the "Pool Address" field on the Cube GUI. Note the port # on the Cube GUI (default is 8330). The username and password field on the Cube GUI could be anything - doesn't matter, as the Pool setting are all specified on the Minepeon Setting page. Since I have several Cubes running, I specify a unique username so that I can identify which cube stats I'm looking at when I SSH into the Minepeon and view the bfgminer miner stats. In Minepeon I use the following command line: /usr/bin/screen -dmS miner /opt/minepeon/bin/bfgminer --http-port 8330 -S noauto -c /opt/minepeon/etc/miner.conf This command line should work if the Cube Port Port is set to 8330 and you don't have any other (non-Proxy) miners running on the Minepeon. If you remove the -S noauto option, you should be able to mine with your USB miners, etc. Assuming you have your Pool information correct in Minepeon, you should be able to see your Cube hashing away on the Minepeon status page or in bfgminer if you SSH into the Raspberry Pi Hope this helps! If this works for you, I would gladly accept a belated Christmas present from you.  1vYG6NVr9nGqqyRL78jQXKLHqPcVX5NKS since my Raspberry is already connected wireless to the internet is their a way to just get a ethernet splitter plug the splitter into my pi and connect my cubes via ethernet to the ethernet splitter on the pi and afterwards point the cubes to my pi's IP? |
|
|
|
Hello everyone, So i am new to mining i'll start of with that.. I just purchased 2 cubes and need some help to set them up. Am used to just plug n play with usb since i had BFL products and never required doing extra work. I know i need a power supply thats strong enough to support both cubes on HIGH clock mode. Any recommendations? also i have a raspberri pi i would use before can i still put this to use in any way with my new cubes?
U can run 2 cubes on a Corsair TX850 PSU. Raspberry Pi works well. I use Minepeon. Just use the --http-port <port#> option in bfgminer and point your Cubes to the IP address/port # for the Pi. Should be a piece of cake. Would the corsair TX850 PSU support both cubes on the HIGH clock setting? If i can use the Raspberry Pi (already running Minepeon) do i connect both miners via usb or through the Ethernet port on the Pi. I currently have the Pi configured to run wirelessly off my wifi connection. |
|
|
|
|
Hello everyone, So i am new to mining i'll start of with that.. I just purchased 2 cubes and need some help to set them up. Am used to just plug n play with usb since i had BFL products and never required doing extra work. I know i need a power supply thats strong enough to support both cubes on HIGH clock mode. Any recommendations? also i have a raspberri pi i would use before can i still put this to use in any way with my new cubes?
|
|
|
|
I placed the order for 2 earlier. did i make the shipping cut off  lol also are the cubes usb enabled now? |
|
|
|
|
"Saturday Comments on Product Line
Rating: 4 votes, 4.00 average.
57 Comments
by BFL_Jody , 07-20-2013 at 06:36 AM (6014 Views)
BFL Products after the FPGA Series:
Part One--NOW Shipping
Jalapenos 4.5 gh/s
Jalapeno with Upgrade 6.5 gh/s
Little Singles 30 gh/s
Singles 60 gh/s
MiniRigs 1500 gh/s (which come as 3x500 gh/s or 8 Singles)
Part Two--Order NOW
5 gh/s BitCoin Miner (will ship after Jalapenos are all shipped)
with Upgrade it's a 7 gh/s Miner
25 gh/s BitCoin Miner (will ship after all Little Singles are shipped)
with Upgrade it's a 30 gh/s Miner
50 gh/s BitCoin Miner (will ship after all Singles are shipped)
with Upgrade it's a 60 gh/s Miner
500 gh/s BitCoin Miner (will ship after all MiniRigs have shipped)"
This is from one of jodys blogs. They plan on clearing part 1 of the miners by the end of september. Jalapenos are almost cleared =) once they are cleared am pretty sure they will start focusing on the singles.
|
|
|
|
What forms of payment will you be accepting?
Bitcoin, obviously. We'll also have a credit card processor, but we are open to suggestions.... John HashFast Paypal? |
|
|
|
|
What forms of payment will you be accepting?
|
|
|
|
|
You should sell your pre-orders since your unhappy =) i'll give u 3btc per jalapeno if their october orders.
|
|
|
|
|
I really hope they cancel all the orders going to germany that way many people will move up in the queue who don't mind waiting just a bit longer........
|
|
|
|
|
Blockchain.info @blockchain 5m
Investigating a database issue. Will be back shortly.
Am guessing their fixing it...
|
|
|
|
Now its saying the site is offline |
|
|
|
Me too  |
|
|
|
Thats such a small device... Heat wont be an issue? |
|
|
|
i havent yet hit my 10 point activity as you mentioned but you added me  please dont delete me (electropyro) i am very interested in your site... Thank you for adding me |
|
|
|
|
i cant wait to get my pacman on =)
|
|
|
|
|
I have 12 chip credits available. for a total value of $300.
Am willing to let go for sale or trade for the following..
--- .5 Btc for all 12
--- Trade for a USB Block Eruptor.
--- 2 chips when they arrive to be sent to me.
pm me if your willing to do the above or want to make an offer.
|
|
|
|
|
