[Built-in Algorithms:]

Dear miners and friends

This is nvOC Community Release based on the original nvOC easy-to-use Linux Nvidia by fullzero

nvOC Community Release like the original nvOC is free and has No Dev-Fee. You can always check 1bash to find developers BTC addresses if you wish to donate.

nvOC Community Release is set of scripts can be use in any Ubuntu system (need some expert edits) or use with provided images (Ubuntu 16.04/18.04) build with Nvidia individual card OC and individual card power limit support, manual fan support, auto launching on boot, auto switch coin based on wtm profits and a single easy to configure Bash Script (1bash) which can be configured from any computer using a text editor.

With nvOC Community Releaed you can set almost anything you wish for in your mining rig and easily add any new coin, algo or miners from 1bash.

Built-in Algorithms:
BITCORE CRYPTONIGHT CRYPTONIGHTHEAVY CRYPTONIGHTV7 CRYPTONIGHTV8 CUCKAROO29 CUCKATOO31 CUCKOOCYCLE DECRED ENERGI EQUIHASH ETHASH GRS LBRY LYRA2V2 LYRA2RE3 LYRA2Z MYR_GR NEOSCRYPT PASCAL PHI1612 PHI2 SIA SIB SKEIN SKUNK X13 X16R X21S X22I XEVAN ZHASH

Builtin miners:
BMINER  CLAYMORE CryptoDredge DSTM ENERGIMINER ETHMINER EWBF GMINER LOLMINER NBMiner PhoenixMiner Tpccminer T_Rex XMR_Stak ZENEMYminer Z_EWBF cpuOPT


Available Settings:

• Set Auto Start Miner on boot
• Set Auto Switching coins
• Set the GPUs you want to mine with
• Use TEAMVIEWER and set the resolution you want to use with it
• Auto Reboot rig timer
• Auto restart miner timer
• Schedule mining to stop and start between given times in a day
• Set your desired worker names
• Set to clear logs on reboot
• Use of SRR
• Control GPU LED and brightness
• Miner Watchdog: Monitors the rig and automatically corrects the detected problems if possible by restarting miner or rig
• Load Check to check system load average and reboot if needed
• Use sys request reboot or normal reboot
• WatchDog check cycle period
• Set Minimum GPU utilization threshold to warn and restart mining if it goes bellow
• Alternate pool settings
• Power limit and Overclock modes: Global, GPU Specific, Algo Specific, Global with GPU Offset, Algo Specific with GPU Offset
• Use Headless mode (for P100 card variants with no monitor output)
• Use OhGodAnETHlargementPill
• Miner Temp Control to automatically adjusts the fan speed to keep the desired temp
• Use manual fan control individual target temps
• Set Hot ShutDown to shutdown rig if temp exceeds
• Set TempControl check cycles
• Set Minimal and Maximal fan speeds
• Set Allowed fan difference, fan adjust and power adjust steps
• Foreman monitoring
• Supports Nicehash, Zpool and MPH Algo mining

Check contributors and all the settings available in 1bash.template

I see the profits shows by whattomine are much difference from what my pool show.
How accurate are the numbers in whattomine?
should I worry if my pool numbers are much lower than what whattomine shows ?
I have a 13 x 1070 rig with average hash rate of 365 MH/s
ethermine.org shows I get 22-23 $/day
When I insert the 365 Mh/s in the ethash rate of whattomine it shows 27$/day

So ...
Am I doing some thing wrong ?
Is there a problem with my setup ?
Should I trust whattomine ?
....

Any one tried the RX 570 and RX 580 Mining cards from biostar?

BIOSTAR RX 570 4GB GDDR5 MINING VA57D5RV42
BIOSTAR RX 580 4GB GDDR5 MINING VA58D5RV42

How are the hash rates ?
Worth to setup a rig with them ?

I have been testing some AutoSwitch miners for over 2 weeks
And here is my observation,
Please share your experience.
So we can make it better.
I tried MultiPoolMiner,  MegaMiner and Nemosminer all are amazing softwares with Zpool and MiningPoolHub.

So in an ideal auto switch mining system switcher check for rates from pools and start mining what is best based on the info it gathered in a given time from pools and your hash rates.
It will continue to mine the coin until a better coin pops up. usually it mines between 3 to 10 minutes.
If miners used to get to their top hash speed at start we would have got lots of profit, but as we all know miners take 30 to 90 second to warm up and reach the optimum speed
So we lose nominal of 60 second on each switch, if miner switch every 5 to 10 minute we lose around 10% to 20% here.
Then comes the AutoExchange.
If you set Auto Exchange which we usually do, We know there is a 4-6 hours delay on most pools to exchange the coin.
Pool told our miner at some point that a coin is at optimum now, but does the exchange of that coin 4-6 hours later will give us same profit ?
Also there is txfee, excahnge fee and some coins may havent reach minimal amount of trade and send back to pool.

I also tested 2 identical rigs (6x1070 both) one on Zpool autoswitch other on claymore dual eth+sia for 2 days, then same for MiningPoolHub,
and I havent got much more than claymore dual mining on same periods.

So please share your thoughts and experience ...