Hello everyone,

I have an amlogic s19 j pro card which I think is totally brick following the firmware update.

I used a TTL cable to analyze the outputs of the board, and here is the log. If anyone has an idea of the fatal error and how to solve it, thank you!

Code:

AXG:BL1:d1dbf2:a4926f;FEAT:F0DC31BC:2000;POC:F;EMMC:800;NAND:0;READ:0;0.0;0.0;CHK:0;
sdio debug board detected
TE: 136410

BL2 Built : 10:38:43, Apr 14 2020. axg gf27ed33 - jenkins@walle02-sh

set vcck to 1100 mv
set vddee to 950 mv
init panel power
Board ID = 0
CPU clk: 1200MHz
DDR low power enabled
DDR3 chl: Rank0 16bit @ 912MHz
bist_test rank: 0 18 00 30 2b 12 45 1d 01 39 25 0b 40 00 00 00 00 00 00 00 00 00 00 00 00 721   - PASS
Rank0: 256MB-2T-13
AddrBus test pass!
NAND init
Load FIP HDR from NAND, src: 0x0000c000, des: 0x01700000, size: 0x00004000, part: 0
Load BL3x from NAND, src: 0x00010000, des: 0x01704000, size: 0x000b7c00, part: 0
NOTICE:  BL31: v1.3(release):3edeb02
NOTICE:  BL31: Built : 16:43:54, Apr 14 2020
NOTICE:  BL31: AXG secure boot!
NOTICE:  BL31: BL33 decompress pass
OPS=0x23
[Image: axg_v1.1.3494-9ec8345 2020-04-17 18:16:39 jenkins@walle02-sh]
25 0c 23 00 fc 7e 94 ad 97 9e 5a 72 80 07 60 27
bl30:axg ver: 9 mode: 0
bl30:axg thermal0
[0.015884 Inits done]
secure task start!
high task start!
low task start!
ERROR:   Error initializing runtime service opteed_fast


U-Boot 2015.01 (Nov 19 2021 - 22:40:09), Build: jenkins-Antminer_S19j-Pro_AMLCtrl_release_tls-12

DRAM:  256 MiB
Relocation Offset is: 0eeaf000
mmu cfg end: 0x20000000
mmu cfg end: 0x20000000
register usb cfg[0][1] = 000000000ff6cfc8
aml_i2c_init_port init regs for 0
NAND:  get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 2c da 90 95 6 0
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
get_sys_clk_rate_mtd() 292, clock setting 250!
m3_nand_adjust_timing() sys_clk_rate 250, bus_c 6, bus_t 7
oob_fill_cnt =32 oob_size =64, bch_bytes =14
ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
oob avail size 6
Creating 1 MTD partitions on "A revision NAND 2Gib MT29F2G08-A":
0x000000000000-0x000000200000 : "bootloader"
A revision NAND 2Gib MT29F2G08-A initialized ok
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 2c da 90 95 6 0
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
get_sys_clk_rate_mtd() 292, clock setting 250!
m3_nand_adjust_timing() sys_clk_rate 250, bus_c 6, bus_t 7
oob_fill_cnt =32 oob_size =64, bch_bytes =14
ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
PLANE change!
plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
aml_nand_init :oobmul=1,oobfree.length=8,oob_size=64
oob avail size 8
nbbt=20
nenv=24
nkey=32
ndtb=40
nddr=44
bbt_start=20 env_start=24 key_start=32 dtb_start=40 ddr_start=44
nbbt: info size=0x800 max_scan_blk=24, start_blk=20
nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1
nbbt free list:
blockN=21, ec=-1, dirty_flag=0
blockN=22, ec=-1, dirty_flag=0
blockN=23, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=1
aml_nand_scan_rsv_info 1137
nbbt valid addr: 280000
aml_nand_bbt_check 1258 bbt is valid, reading.
aml_nand_read_rsv_info:446,read nbbt info to 280000
nenv: info size=0x10000 max_scan_blk=32, start_blk=24
nenv : phy_blk_addr=25, ec=0, phy_page_addr=0, timestamp=6
nenv free list:
blockN=24, ec=-1, dirty_flag=0
blockN=26, ec=-1, dirty_flag=0
blockN=27, ec=-1, dirty_flag=0
blockN=28, ec=-1, dirty_flag=0
blockN=29, ec=-1, dirty_flag=0
blockN=30, ec=-1, dirty_flag=0
blockN=31, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=32
aml_nand_scan_rsv_info 1137
nenv valid addr: 330000
nkey: info size=0x8000 max_scan_blk=40, start_blk=32
nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
nkey free list:
blockN=32, ec=-1, dirty_flag=0
blockN=33, ec=-1, dirty_flag=0
blockN=34, ec=-1, dirty_flag=0
blockN=35, ec=-1, dirty_flag=0
blockN=36, ec=-1, dirty_flag=0
blockN=37, ec=-1, dirty_flag=0
blockN=38, ec=-1, dirty_flag=0
blockN=39, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=16
nkey valid addr: fffffffffffe0000
aml_nand_rsv_info_check_except_bbt 1228 NO nkey exist
ndtb: info size=0x20000 max_scan_blk=44, start_blk=40
ndtb : phy_blk_addr=41, ec=0, phy_page_addr=0, timestamp=2
ndtb free list:
blockN=40, ec=-1, dirty_flag=0
blockN=42, ec=-1, dirty_flag=0
blockN=43, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=64
aml_nand_scan_rsv_info 1137
ndtb valid addr: 520000
nddr: info size=0x800 max_scan_blk=46, start_blk=44
nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
nddr free list:
blockN=44, ec=-1, dirty_flag=0
blockN=45, ec=-1, dirty_flag=0
aml_nand_scan_rsv_info 1134: page_num=1
nddr valid addr: fffffffffffe0000
aml_nand_rsv_info_check_except_bbt 1228 NO nddr exist
tpl: off 8388608, size 8388608
Creating 6 MTD partitions on "A revision NAND 2Gib MT29F2G08-A":
0x000000800000-0x000001000000 : "tpl"
0x000001000000-0x000001200000 : "misc"
0x000001200000-0x000002200000 : "recovery"
0x000002200000-0x000004200000 : "boot"
0x000004200000-0x000004700000 : "config"
0x000004700000-0x000010000000 : "nvdata"
A revision NAND 2Gib MT29F2G08-A initialized ok
MMC:   aml_priv->desc_buf = 0x000000000dead560
aml_priv->desc_buf = 0x000000000deaf8a0
SDIO Port B: 0, SDIO Port C: 1
uboot env amlnf_env_read : ####
aml_nand_read_rsv_info:446,read nenv info to 330000
In:    serial
Out:   serial
Err:   serial
aml log : internal sys error!
reboot_mode=cold_boot
[store]To run cmd[amlnf dtb_read 0x1000000 0x40000]
sub cmd dtb
new argv[1] dtb_read
do_dtb_ops(): argc 4
arg 0: amlnf
arg 1: dtb_read
arg 2: 0x1000000
arg 3: 0x40000
do_dtb_ops() read
amlnf_dtb_read: ####
warnning!!! amlnf_dtb_read dtd length too much
aml_nand_read_rsv_info:446,read ndtb info to 520000
do_dtb_ops(): 262144 bytes read : OK
aml log : R2048 check pass!
      Amlogic multi-DTB tool
      GZIP format, decompress...
      Multi DTB detected.
      Multi DTB tool version: v2.
      Support 2 DTBS.
debug ddr size: 0x10000000
checkhw board adc:0
      Found DTB for "axg_s400_v03sbr"
gpio: pin GPIOAO_7 (gpio 7) value is 1
[MSG]usb start
(Re)start USB...
USB0:   USB3.0 XHCI init start
Register 1000140 NbrPorts 1
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
fail in cmd [fatsize usb 0 aml_sdc_burn.ini], rcode 1
ERR(../drivers/usb/gadget/v2_burning/v2_usb_burn/optimus_usb_burn.c)L41:The [aml_sdc_burn.ini] not exist in udisk
Net:   sysnopsys gmac3.7
Phy 0 not found
dwmac.ff3f0000amlkey_init() enter!
amlnf_key_read: ####
amlnf_key_read key data len too much
aml_nand_ext_read_rsv_info 520: nkey is invalid! read exit![EFUSE_MSG]keynum is 4
MACADDR:02:97:ad:94:7e:fc(from chipid)

ramdump_init, add:0, size:0
usb_update_flag=
Start read misc partition datas!
[burnup]Rd:Up sz 0x440 to align 0x1000
info->attemp_times = 0
info->active_slot = 0
info->slot_info[0].bootable = 1
info->slot_info[0].online = 1
info->slot_info[1].bootable = 0
info->slot_info[1].online = 0
info->attemp_times = 0
attemp_times = 0
active slot = 0
wipe_data=successful
wipe_cache=successful
recovery_status=
upgrade_step=2
[aml_i2c_xfer] error ret = -5   i2c master b current slave addr is 0x1f
i2c_write: i2c transfer failed
Error writing the chip: -5
[aml_i2c_xfer] error ret = -5   i2c master b current slave addr is 0x1f
i2c_write: i2c transfer failed
Error writing the chip: -5
[aml_i2c_xfer] error ret = -5   i2c master b current slave addr is 0x1f
i2c_write: i2c transfer failed
Error writing the chip: -5
[aml_i2c_xfer] error ret = -5   i2c master b current slave addr is 0x1f
i2c_write: i2c transfer failed
Error writing the chip: -5
s_version: U-Boot 2015.01
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
s_version: U-Boot 2015.01
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
Hit Enter or space or Ctrl+C key to stop autoboot -- :  0
CONFIG_SYSTEM_AS_ROOT: null
system_mode: 0
[imgread]szTimeStamp[2021111922403917]
[imgread]secureKernelImgSz=0xc2c000
aml log : R-2048 check pass!
aml log : R2048 check pass!
aml log : R2048 check pass!
aml log : R2048 check pass!
avb2: 0
save_power_post ...
avb2: 0
## Booting Android Image at 0x01080000 ...
reloc_addr =ded86d0
copy done
Kernel command line: init=/sbin/init
[store]Is good fdt check header, no need decrypt!
load dtb from 0x1000000 ......
      Amlogic multi-DTB tool
      Single DTB detected
   Uncompressing Kernel Image ... OK
   kernel loaded at 0x01080000, end = 0x0203aa00
   Loading Ramdisk to 0d83b000, end 0de9d000 ... OK
   Loading Device Tree to 000000000d82c000, end 000000000d83a188 ... OK
fdt_fixup_memory_banks, reg:0000000000000000

Starting kernel ...

uboot time: 4224925 us
[    0.000000@0] Booting Linux on physical CPU 0x0
[    0.000000@0] Linux version 4.9.113 (jenkins@nomd-nomd-fwc-bj) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Fri Nov 19 22:32:14 CST 2021
[    0.000000@0] Boot CPU: AArch64 Processor [410fd034]
[    0.000000@0] earlycon: aml_uart0 at MMIO 0x00000000ff803000 (options '')
[    0.000000@0] bootconsole [aml_uart0] enabled
[    0.000000@0] efi: Getting EFI parameters from FDT:
[    0.000000@0] efi: UEFI not found.
[    0.000000@0]        07400000 - 07500000,     1024 KB, ramoops@0x07400000
[    0.000000@0] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB
[    0.000000@0]        05000000 - 05400000,     4096 KB, linux,secmon
[    0.000000@0] __reserved_mem_alloc_size, start:0x000000003e000000, end:0x0000000040000000, len:32 MiB
[    0.000000@0] failed to allocate memory for node linux,meson-fb, size:32 MB
[    0.000000@0] cma: Reserved 8 MiB at 0x000000000f800000
[    0.000000@0] psci: probing for conduit method from DT.
[    0.000000@0] psci: PSCIv1.0 detected in firmware.
[    0.000000@0] psci: Using standard PSCI v0.2 function IDs
[    0.000000@0] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000@0] psci: SMC Calling Convention v1.1
[    0.000000@0] percpu: Embedded 25 pages/cpu @ffffffc00f753000 s64536 r8192 d29672 u102400
[    0.000000@0] Detected VIPT I-cache on CPU0
[    0.000000@0] CPU features: enabling workaround for ARM erratum 845719
[    0.000000@0] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64512
[    0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=,loaded,androidboot.selinux=enforcing androidboot.firstboot=1 jtag=disable androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01 androidboot.build.expect.baseband=N/A androidboot.serialno=1234567890 rootfstype=ramfs init=/sbin/init
[    0.000000@0] PID hash table entries: 1024 (order: 1, 8192 bytes)
[    0.000000@0] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.000000@0] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
[    0.000000@0] Memory: 219920K/262144K available (8764K kernel code, 1194K rwdata, 2428K rodata, 3648K init, 1018K bss, 29936K reserved, 12288K cma-reserved)
[    0.000000@0] Virtual kernel memory layout:
[    0.000000@0]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000@0]     vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000   (   250 GB)
[    0.000000@0]       .text : 0xffffff8009080000 - 0xffffff8009910000   (  8768 KB)
[    0.000000@0]     .rodata : 0xffffff8009910000 - 0xffffff8009b80000   (  2496 KB)
[    0.000000@0]       .init : 0xffffff8009b80000 - 0xffffff8009f10000   (  3648 KB)
[    0.000000@0]       .data : 0xffffff8009f10000 - 0xffffff800a03aa00   (  1195 KB)
[    0.000000@0]        .bss : 0xffffff800a03aa00 - 0xffffff800a139534   (  1019 KB)
[    0.000000@0]     fixed   : 0xffffffbefe7fb000 - 0xffffffbefec00000   (  4116 KB)
[    0.000000@0]     PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000   (    16 MB)
[    0.000000@0]     vmemmap : 0xffffffbf00000000 - 0xffffffc000000000   (     4 GB maximum)
[    0.000000@0]               0xffffffbf00000000 - 0xffffffbf00400000   (     4 MB actual)
[    0.000000@0]     memory  : 0xffffffc000000000 - 0xffffffc010000000   (   256 MB)
[    0.000000@0] can't find symbol:arm_dma_alloc
[    0.000000@0] can't find symbol:__alloc_from_contiguous
[    0.000000@0] can't find symbol:cma_allocator_alloc
[    0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000@0] Preemptible hierarchical RCU implementation.
[    0.000000@0]        Build-time adjustment of leaf fanout to 64.
[    0.000000@0]        RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[    0.000000@0]
[    0.000000@0] **********************************************************
[    0.000000@0] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
[    0.000000@0] **                                                      **
[    0.000000@0] ** trace_printk() being used. Allocating extra memory.  **
[    0.000000@0] **                                                      **
[    0.000000@0] ** This means that this is a DEBUG kernel and it is     **
[    0.000000@0] ** unsafe for production use.                           **
[    0.000000@0] **                                                      **
[    0.000000@0] ** If you see this message and you are not debugging    **
[    0.000000@0] ** the kernel, report this immediately to your vendor!  **
[    0.000000@0] **                                                      **
[    0.000000@0] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
[    0.000000@0] **********************************************************
[    0.000000@0] NR_IRQS:64 nr_irqs:64 0
[    0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[    0.000000@0] axg_aoclkc_init: register ao clk ok![    0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[    0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[    0.000000@0] axg_amlogic_init_media: register meson media clk
[    0.000000@0] axg_amlogic_init_misc: register amlogic axg misc clks
[    0.000000@0] axg_amlogic_init_misc: register amlogic sdemmc clk
[    0.000000@0] axg_clkc_init initialization complete
[    0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.008252@0] meson_bc_timer: mclk->mux_reg =ffffff800800a190,mclk->reg =ffffff800800c194
[    0.016907@0] Console: colour dummy device 80x25
[    0.021106@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.031586@0] pid_max: default: 32768 minimum: 301
[    0.036439@0] thread_stack_cache_init, vmap:ffffffc00edaf600, bitmap:ffffffc00eda3000, cache page:ede0
[    0.045773@0] thread_stack_cache_init, allocation vm area:ffffffc00edd94c0, addr:ffffff8020000000, size:20001000
[    0.056005@0] cpu 0, vmap_stack:[ffffffc00f75c960-ffffffc00f760950]
[    0.062304@0] cpu 0, irq_stack: [ffffffc00f753060-ffffffc00f757050]
[    0.068603@0] cpu 1, vmap_stack:[ffffffc00f775960-ffffffc00f779950]
[    0.074903@0] cpu 1, irq_stack: [ffffffc00f76c060-ffffffc00f770050]
[    0.081203@0] cpu 2, vmap_stack:[ffffffc00f78e960-ffffffc00f792950]
[    0.087503@0] cpu 2, irq_stack: [ffffffc00f785060-ffffffc00f789050]
[    0.093803@0] cpu 3, vmap_stack:[ffffffc00f7a7960-ffffffc00f7ab950]
[    0.100103@0] cpu 3, irq_stack: [ffffffc00f79e060-ffffffc00f7a2050]
[    0.106465@0] Security Framework initialized
[    0.110696@0] SELinux:  Initializing.
[    0.114428@0] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
[    0.121108@0] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)
[    0.128873@0] ftrace: allocating 30089 entries in 118 pages
[    0.184510@0] sched-energy: CPU device node has no sched-energy-costs
[    0.185326@0] CPU0: update cpu_capacity 1024
[    0.189652@0] ASID allocator initialised with 32768 entries
[    0.227632@0] secmon: can't fine clear_range
[    0.227841@0] EFI services will not be available.
[    0.231112@0] Meson chip version = RevC (25:C - 23:0)
[    0.264979@1] Detected VIPT I-cache on CPU1
[    0.265040@1] CPU1: update cpu_capacity 1024
[    0.265042@1] CPU1: Booted secondary processor [410fd034]
[    0.293040@2] Detected VIPT I-cache on CPU2
[    0.293096@2] CPU2: update cpu_capacity 1024
[    0.293098@2] CPU2: Booted secondary processor [410fd034]
[    0.321116@3] Detected VIPT I-cache on CPU3
[    0.321169@3] CPU3: update cpu_capacity 1024
[    0.321171@3] CPU3: Booted secondary processor [410fd034]
[    0.321262@0] Brought up 4 CPUs
[    0.360482@0] SMP: Total of 4 processors activated.
[    0.365390@0] CPU features: detected feature: 32-bit EL0 Support
[    0.371427@0] CPU features: detected feature: Kernel page table isolation (KPTI)
[    0.381994@0] CPU: All CPU(s) started at EL2
[    0.383167@0] alternatives: patching kernel code
[    0.388493@1] addr:ffffff802007be10 is in kernel, size fix 4096->10, data:mode=0755
[    0.395698@0] devtmpfs: initialized
[    0.411161@0] DMI not present or invalid.
[    0.411522@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.419546@0] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.426106@0] pinctrl core: initialized pinctrl subsystem
[    0.432534@0] NET: Registered protocol family 16
[    0.452056@0] cpuidle: using governor menu
[    0.452549@0] vdso: 2 pages (1 code @ ffffff8009917000, 1 data @ ffffff8009f14000)
[    0.458169@0] hw-breakpoint: found 6 breakpoint and 2 watchpoint registers.
[    0.465578@0] DMA: preallocated 256 KiB pool for atomic allocations
[    0.471744@0] clkmsr: clkmsr: driver init
[    0.475764@0] aml_watch_point_probe, in, wp:2
[    0.480363@0] pstore: using zlib compression
[    0.484708@0] console [pstore-1] enabled
[    0.488041@0] pstore: Registered ramoops as persistent store backend
[    0.494454@0] ramoops: attached 0x100000@0x7400000, ecc: 0/0
domain-0 init dvfs: 3
[    0.508799@0] aml_iomap: amlogic iomap probe done
[    0.515765@0] clkmsr: msr_clk_reg0=ffffff800817e004,msr_clk_reg2=ffffff80081d100c
[    0.517701@0] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0
[    0.618064@0] usbcore: registered new interface driver usbfs
[    0.618239@0] usbcore: registered new interface driver hub
[    0.623852@0] usbcore: registered new device driver usb
[    0.629140@0] pps_core: LinuxPPS API ver. 1 registered
[    0.634088@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.643474@0] PTP clock support registered
[    0.647834@0] dmi: Firmware registration failed.
[    0.656640@0] secmon: reserve_mem_size:0x300000
[    0.656784@0] secmon secmon: assigned reserved memory node linux,secmon
[    0.663792@0] secmon: get page:ffffffbf00140000, 5000
[    0.668466@0] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000
[    0.676827@0] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000
[    0.684735@0] NetLabel: Initializing
[    0.686877@0] NetLabel:  domain hash size = 128
[    0.691464@0] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.696718@0] NetLabel:  unlabeled traffic allowed by default
[    0.703305@0] clocksource: Switched to clocksource arch_sys_counter
[    0.832758@0] VFS: Disk quotas dquot_6.6.0
[    0.832906@0] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.859843@1] NET: Registered protocol family 2
[    0.860944@1] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.866103@1] TCP bind hash table entries: 2048 (order: 3, 32768 bytes)
[    0.872770@1] TCP: Hash tables configured (established 2048 bind 2048)
[    0.879355@1] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.885304@1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.892046@1] NET: Registered protocol family 1
[    0.897021@1] RPC: Registered named UNIX socket transport module.
[    0.902435@1] RPC: Registered udp transport module.
[    0.907326@1] RPC: Registered tcp transport module.
[    0.912214@1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.921441@1] Unpacking initramfs...
[    1.421674@3] Initramfs unpacking failed: junk in compressed archive
[    1.428528@3] Freeing initrd memory: 6536K
[    1.429403@3] hw perfevents: clusterb_enabled = 0
[    1.431780@3] hw perfevents: cpumasks 0xf, 0x0
[    1.436248@3] hw perfevents: cluster A irq = 7
[    1.440814@3] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    1.450979@3] audit: initializing netlink subsys (disabled)
[    1.454377@3] audit: type=2000 audit(1.268:1): initialized
[    1.461681@3] workingset: timestamp_bits=62 max_order=16 bucket_order=0
[    1.486533@3] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.489593@3] NFS: Registering the id_resolver key type
[    1.492263@3] Key type id_resolver registered
[    1.496569@3] Key type id_legacy registered
[    1.501204@3] fuse init (API version 7.26)
[    1.513161@3] NET: Registered protocol family 38
[    1.513219@3] Key type asymmetric registered
[    1.516465@3] Asymmetric key parser 'x509' registered
[    1.521965@3] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    1.529162@3] io scheduler noop registered (default)
[    1.534130@3] io scheduler deadline registered
[    1.539030@3] io scheduler cfq registered
[    1.560049@2] random: fast init done
[    1.560149@2] random: crng init done
[    1.560622@3] Unable to detect cache hierarchy for CPU 0
[    1.603337@3] loop: module loaded
[    1.604937@3] zram: Added device: zram0
[    1.605359@3] mtdoops: mtd device (mtddev=name/number) must be supplied
[    1.612105@3] libphy: Fixed MDIO Bus: probed
[    1.616634@3] tun: Universal TUN/TAP device driver, 1.6
[    1.621088@3] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.629293@3]  ee eth reset:Addr = ffffff80081fd008
[    1.636806@3] meson6-dwmac ff3f0000.ethernet: no reset control found
[    1.638730@3] stmmac - user ID: 0x11, Synopsys ID: 0x37
[    1.644011@3]  Ring mode enabled
[    1.647210@3]  DMA HW capability register supported[    1.651953@3]  Normal descriptors
[    1.655259@3]  RX Checksum Offload Engine supported
[    1.660184@3]        COE Type 2
[    1.662783@3]  TX Checksum insertion supported
[    1.667262@3]  Wake-Up On Lan supported
[    1.671215@3]  Enable RX Mitigation via HW Watchdog Timer
[    1.679356@3] libphy: stmmac: probed
[    1.680114@3] eth%d: No PHY found

Hello guys!

Happy new year

Today? I repair a 0 asic hashboard. To begining, it was just a RI signal problem appear on chip 30, I just replace him.
Now,
RI signal is good in every row (1,8v).
all CLK signal and everyone are on 0,9 (lowest is 0,896v). So I guess all its okay.
all each core between next row are 0,4v (lowest is 0,394v). So its okay too ?

But when I run the miner, he detect 0 ASIC. In miner status I got my pool, fan, and one line after antminer shows "ASIC 0 ; IDEAL HS 0; REAL TIME HS 0;" So I guess my hashboard is detected normaly ?
 
I check my datacable, and PSU cable, all is good cuz with another hashboard everything is great.

I post my kernel log here if anyone see something...

Thanks

Code:

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-g16220c3 (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #83 SMP PREEMPT Thu Jul 12 11:42:53 CST 2018
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 16800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 126976
[    0.000000] free_area_init_node: node 0, pgdat c074ac00, node_mem_map debd8000
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984
[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 364316K/507904K available (5057K kernel code, 284K rwdata, 1928K rodata, 204K init, 258K bss, 143588K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06da8ac   (6987 kB)
[    0.000000]       .init : 0xc06db000 - 0xc070e380   ( 205 kB)
[    0.000000]       .data : 0xc0710000 - 0xc0757138   ( 285 kB)
[    0.000000]        .bss : 0xc0757144 - 0xc0797bfc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to df802000
[    0.000000] zynq_clock_init: clkc starts at df802100
[    0.000000] Zynq clock init
[    0.000014] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000290] ps7-ttc #0 at df804000, irq=43
[    0.000590] Console: colour dummy device 80x30
[    0.000619] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040195] pid_max: default: 32768 minimum: 301
[    0.040400] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040419] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.042581] CPU: Testing write buffer coherency: ok
[    0.042892] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.042949] Setting up static identity map for 0x4cb118 - 0x4cb170
[    0.043169] L310 cache controller enabled
[    0.043189] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.120983] CPU1: Booted secondary processor
[    0.210216] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210347] Brought up 2 CPUs
[    0.210366] SMP: Total of 2 processors activated.
[    0.210375] CPU: All CPU(s) started in SVC mode.
[    0.211044] devtmpfs: initialized
[    0.213471] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214663] regulator-dummy: no parameters
[    0.222000] NET: Registered protocol family 16
[    0.224213] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.226470] cpuidle: using governor ladder
[    0.226483] cpuidle: using governor menu
[    0.233836] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.235350] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.235363] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.235473] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[    0.257233] bio: create slab <bio-0> at 0
[    0.258606] vgaarb: loaded
[    0.259301] SCSI subsystem initialized
[    0.260318] usbcore: registered new interface driver usbfs
[    0.260890] usbcore: registered new interface driver hub
[    0.261165] usbcore: registered new device driver usb
[    0.261682] media: Linux media interface: v0.10
[    0.261845] Linux video capture interface: v2.00
[    0.262084] pps_core: LinuxPPS API ver. 1 registered
[    0.262096] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.262217] PTP clock support registered
[    0.262575] EDAC MC: Ver: 3.0.0
[    0.263762] Advanced Linux Sound Architecture Driver Initialized.
[    0.266483] DMA-API: preallocated 4096 debug entries
[    0.266497] DMA-API: debugging enabled by kernel config
[    0.266565] Switched to clocksource arm_global_timer
[    0.286418] NET: Registered protocol family 2
[    0.287129] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.287187] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.287272] TCP: Hash tables configured (established 4096 bind 4096)
[    0.287316] TCP: reno registered
[    0.287333] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.287364] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.287607] NET: Registered protocol family 1
[    0.287946] RPC: Registered named UNIX socket transport module.
[    0.287959] RPC: Registered udp transport module.
[    0.287967] RPC: Registered tcp transport module.
[    0.287976] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.287988] PCI: CLS 0 bytes, default 64
[    0.288407] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.290401] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.292447] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.292635] msgmni has been set to 967
[    0.293388] io scheduler noop registered
[    0.293401] io scheduler deadline registered
[    0.293441] io scheduler cfq registered (default)
[    0.301973] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.301992] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.425659] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    0.993381] console [ttyPS0] enabled
[    0.997645] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.005232] [drm] Initialized drm 1.1.0 20060810
[    1.022339] brd: module loaded
[    1.031759] loop: module loaded
[    1.041216] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.047054] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.054769] libphy: XEMACPS mii bus: probed
[    1.059386] ------------- phy_id = 0x3625e62
[    1.064108] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.072911] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.079704] ehci-pci: EHCI PCI platform driver
[    1.086936] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.093722] usbcore: registered new interface driver usb-storage
[    1.100608] mousedev: PS/2 mouse device common for all mice
[    1.106726] i2c /dev entries driver
[    1.113628] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.119135] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.124999] Xilinx Zynq CpuIdle Driver started
[    1.129893] sdhci: Secure Digital Host Controller Interface driver
[    1.135985] sdhci: Copyright(c) Pierre Ossman
[    1.140348] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.147195] mmc0: no vqmmc regulator found
[    1.151205] mmc0: no vmmc regulator found
[    1.186585] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.195273] usbcore: registered new interface driver usbhid
[    1.200776] usbhid: USB HID core driver
[    1.205479] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.211778] nand: Micron MT29F2G08ABAEAWP
[    1.215740] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.221677] Bad block table found at page 131008, version 0x01
[    1.227899] Bad block table found at page 130944, version 0x01
[    1.233887] nand_read_bbt: bad block at 0x0000079a0000
[    1.238977] nand_read_bbt: bad block at 0x00000b120000
[    1.244119] 3 ofpart partitions found on MTD device pl353-nand
[    1.249898] Creating 3 MTD partitions on "pl353-nand":
[    1.255003] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.263057] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.270366] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.281074] TCP: cubic registered
[    1.284313] NET: Registered protocol family 17
[    1.289003] Registering SWP/SWPB emulation handler
[    1.294886] regulator-dummy: disabling
[    1.299189] UBI: attaching mtd1 to ubi0
[    1.826183] UBI: scanning is finished
[    1.837820] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.844875] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.851672] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.858348] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.865185] UBI: good PEBs: 1151, bad PEBs: 1, corrupted PEBs: 0
[    1.871195] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.878306] UBI: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1113221046
[    1.887337] UBI: available PEBs: 0, total reserved PEBs: 1151, PEBs reserved for bad PEB handling: 39
[    1.896533] UBI: background thread "ubi_bgt0d" started, PID 1084
[    1.896538] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.900460] ALSA device list:
[    1.900464]   No soundcards found.
[    1.916856] UBIFS: background thread "ubifs_bgt0_0" started, PID 1086
[    1.945945] UBIFS: recovery needed
[    2.028323] UBIFS: recovery completed
[    2.031991] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.037933] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.047079] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.056934] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.061959] UBIFS: media format: w4/r0 (latest is w4/r0), UUID E8A4479F-B15D-4C7A-964D-0F246E2BB6ED, small LPT model
[    2.073253] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.080447] devtmpfs: mounted
[    2.083552] Freeing unused kernel memory: 204K (c06db000 - c070e000)
[    2.919418] random: dd urandom read with 1 bits of entropy available
[    3.306607]
[    3.306607] bcm54xx_config_init
[    4.376617]
[    4.376617] bcm54xx_config_init
[    8.377439] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[    8.383542] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[   23.195956] In axi fpga driver!
[   23.199058] request_mem_region OK!
[   23.202418] AXI fpga dev virtual address is 0xdf9fe000
[   23.207556] *base_vir_addr = 0xc51e
[   23.222030] In fpga mem driver!
[   23.225346] request_mem_region OK!
[   23.228978] fpga mem virtual address is 0xe2000000
[   24.026605]
[   24.026605] bcm54xx_config_init
[   25.116585]
[   25.116585] bcm54xx_config_init
[   29.117427] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[   29.123537] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
main.c:13992: log_level = 4
main.c:14019: This is XILINX board. Totalram:       507486208
main.c:14031: Detect 512MB control board of XILINX
driver-bitmain.c:1776: mmap axi_fpga_addr = 0xb6fc2000
driver-bitmain.c:1781: axi_fpga_addr data = 0xc51e
driver-bitmain.c:1797: mmap fpga_mem_addr = 0xb5dbb000
driver-bitmain.c:994: forceFreq=-1 forceFlag=0
driver-bitmain.c:1696: min work minertest[0]:912


main.c:8570: DETECT HW version=0000c51e
main.c:14064: miner ID : 8064cd8162b5885c
main.c:14089: Miner Type = S9
main.c:14101: AsicType = 1387
main.c:14104: real AsicNum = 63
main.c:14197: use critical mode to search freq...
driver-bitmain.c:1876: get PLUG ON=0x00000020
driver-bitmain.c:1946: Find hashboard on Chain[5]
main.c:2282: Check chain[5] PIC fw version=0x03
main.c:8940: read pic freq and badcore num...
main.c:8961: chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9099: chain[5] has freq in PIC and will jump over...
main.c:9103: Chain[5] has core num in PIC
main.c:9113: Chain[5] ASIC[7] has core num=15
main.c:9113: Chain[5] ASIC[15] has core num=15
main.c:9113: Chain[5] ASIC[17] has core num=15
main.c:9113: Chain[5] ASIC[37] has core num=1
main.c:9113: Chain[5] ASIC[45] has core num=12
main.c:2282: Check chain[5] PIC fw version=0x03
main.c:9183: get PIC voltage=6 on chain[5], value=940
main.c:9349: chain[5] temp offset record: 62,0,0,0,0,0,35,28
main.c:9366: chain[5] temp chip I2C addr=0x98
main.c:9372: chain[5] has no middle temp, use special fix mode.
main.c:13956: total_exist_chain_num = 1
main.c:9562: CRC error counter=0
main.c:9577: set command mode to VIL
main.c:9649:
--- check asic number
main.c:9745: After Get ASIC NUM CRC error counter=0
main.c:9768: set_baud=0
main.c:10693: The min freq=700
main.c:10695: set real timeout 52, need sleep=379392
main.c:12825: After TEST CRC error counter=0
main.c:14236: search freq for 1 times, completed chain = 1, total chain num = 1
board_frq_tuning.c:628: single_board_frq_tuning enter
board_frq_tuning.c:629: min_rate, des_rate, fix_volt:13800, 14000, 880
board_frq_tuning.c:254: force_freq not set, don't need tuning
main.c:14645: restart Miner chance num=2
main.c:14685: waiting for receive_func to exit!
main.c:14699: waiting for pic heart to exit!
main.c:13927: bmminer not found= 1885 root       0:00 grep bmminer

main.c:14758: bmminer not found, restart bmminer ...
driver-btm-c5.c:12243:bitmain_c5_init: This is user mode for mining
driver-btm-c5.c:12292:bitmain_c5_init: Detect 512MB control board of XILINX
driver-btm-c5.c:12313:bitmain_c5_init: Miner Type = S9
driver-btm-c5.c:12324:bitmain_c5_init: Miner compile time: Wed Jul 31 16:18:27 CST 2019 type: Antminer S9
driver-btm-c5.c:12414:bitmain_c5_init: miner ID : 8064cd8162b5885c
driver-btm-c5.c:12571:bitmain_c5_init: Checking fans...
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=6360
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=6360
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=6000
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=6360
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=6000
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=6360
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=6000
driver-btm-c5.c:13108:bitmain_c5_init: chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
driver-btm-c5.c:13122:bitmain_c5_init: last_freq: 0x00 0x7d 0x00 0x4c 0x00 0x4c 0x04 0x4c 0x0c 0x4c 0x00 0x4c 0x03 0x4c 0x03 0x4c 0x03 0x4c 0x03 0x4c 0x03 0x4c 0x03 0x4c 0x01 0x4c 0x01 0x4c 0x0f 0x4c 0x0f 0x4c 0x0f 0x4c 0x0f 0x4c 0x05 0x4c 0x09 0x4c 0x23 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c
driver-btm-c5.c:13149:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:13155:bitmain_c5_init: Detect: S9_63 use voltage level=1 : 1
driver-btm-c5.c:13171:bitmain_c5_init: Chain[J6] has backup chain_voltage=890
driver-btm-c5.c:13188:bitmain_c5_init: No scan based on domain
driver-btm-c5.c:1899:jump_to_app_CheckAndRestorePIC: Check chain[5] PIC fw version=0x03
driver-btm-c5.c:12195:init_exist_chain_table: total_exist_chain_num = 1
driver-btm-c5.c:13303:bitmain_c5_init: Chain[J6] orignal chain_voltage_pic=6 value=940
driver-btm-c5.c:13320:bitmain_c5_init: Chain[J6] will use backup chain_voltage_pic=890 [91]
driver-btm-c5.c:13330:bitmain_c5_init: Chain[J6] get working chain_voltage_pic=91
driver-btm-c5.c:13421:bitmain_c5_init: Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:4571:set_frequency: miner total rate=0GH/s ideal_total_hash_rate = 0GH/s

driver-btm-c5.c:4819:set_frequency: Miner fix freq ...
driver-btm-c5.c:5119:set_frequency: max freq = 100
driver-btm-c5.c:4162:ProcessFixFreq: totalRate = 0, fixed_totalRate = 0
driver-btm-c5.c:9604:init_uart_baud: set baud=1
driver-btm-c5.c:12103:set_working_voltage: setting to working voltage...
driver-btm-c5.c:13954:bitmain_c5_init: start thread for read temp
setStartTimePoint total_tv_start_sys=108 total_tv_end_sys=109
driver-btm-c5.c:8727:read_temp_func: bring_up_pcb_temp = -100
driver-btm-c5.c:10320:check_system_work: restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
Done check_asic_reg
Max pcb temp : -100
set FAN speed according to: temp_highest=-100 temp_top1[PWM_T]=-100 temp_top1[TEMP_POS_LOCAL]=-100 temp_change=-100 fix_fan_steps=0
FAN PWM: 0
read_temp_func Done!
CRC error counter=0

Hi guys, small question on a hashboard s9 4.21, I replaced a chip, the clock is well at 0.9 but the RI at 0v, the LDO comes out well 1.8v and 2.5v bottom pin.
All the small resistors are at the right ohm. After soldering the chip, I checked the resistors CLK30 CO30 RI30 BO30 RST30 are good in ohm. I conclude that the chip soldering is good?
Any idea where it comes from?

Thanks!

Hi everyone, I'm on a s9 13th and a card shows me signs of a hashrate drop after 5 minutes of mining (OS braiins ).  I look at the logs everything is top, starts correctly the only concern being this line which appears before the fall of hashrate:

Code:

2022-11-30T13:20:12.562165Z ERROR bosminer_hal::sensor: Sensor hb8[ii_hwmon::tmp451::TMP451]: read failed: I2C error: general error Hashchip: no response for read_register(reg=0x20) from chip One(61)

I then looked more closely with a magnifying glass by desoldering the heat sinks, it seems okay to me on tmp541 chip, no dust, the welds are not cracked… a friend told me that as for the s17 the welds crack over time  and make false contacts.


I noticed that on the hashboard when the sensor goes wrong, the little red light flashes more slowly like a bad contact (if it helps I say so)

also in the line of code I saw write Chip 61, so I decided to test the chip as well as its surroundings and I came across the correct values ​​of CLK: 0.9 and RI 1.8 in 12v plug.

from what I understood it is, the more its heating (so after 5min to heat up) the closer we get to a crash point because of the sensor (or other)

for the moment I am there without too much additional info… an idea maybe?

Big Thanks 🫡

Hey all !

I search a pool or API for multi adresses payout..

One exemple , Tony and Bobby have invest in 3 card per man , so total rig of 6 card

Tony and Bobby want each payout on each adresses ..

Pool or API can do it ?

Thanks you ! (and sry for my english so bad )

Hey !

J’aimerai savoir si il est possible de payer via un rig sur plusieurs adresse. Exemple simple
Kevin et Adrien on investi 3 cg chacun , donc un rig de 6 , chacun veut sa part sur son adresse perso , il est possible de le faire depuis Claymore ou une pool ?

Merci !