Give the beta 2.0 a go, the update simplified. Just run flash.bat and type in com port.

Device setup is slightly different but I'm sure most can figure it out.

If I added resistors to the jump wires on the backpack you could remove them, it makes the screen much brighter though. You could also try unplug the four cables in to the backpack and plug in again, perhaps not making the best contact. Be sure not to mess up the order.

It's a two step process now. Note the IP under "Connected" during startup (https://youtu.be/-vIwev8wiSc). Navigate to that on phone/laptop/PC to finish setup.

There will be a 2.0 final at some stage with more sensible defaults and perhaps pause on the IP address screen for a bit longer and any other sensible changes people suggest.

My ABN has lapsed and personal circumstances have changed so unfortunately, probably not. It's a shame because I have way to many parts here in my garage.

If you want to give soldering a go or know someone who can do it for you think you may need to swap the esp8266 board on your device 1 just make sure to wire it up the same. If the computer can't see it you can't update it unfortunately. The are about $7 -10 AUD from ali express, I would send you one but it would cost $25 shipping.

https://youtu.be/MlnxZJiMaQA

https://youtu.be/-vIwev8wiSc

From my testing it always shows IP at boot, it is quicker than the older firmware though?

Beta 2.0 will not reset if you have yellow circuit board. If you were one of the first seven customers you have yellow circuit board and no external reset button in a plastic box it's not going to reset any more, please use v1.7 if you require this.

You can change all the displayed currency by navigating to the IP address shown on screen during startup, when it comes out of beta I'll put more sensible defaults.

I just updated the batch file to give more verbose output.

As for your device that's not detected very strange especially because you had one that worked. Can you unplug the side jumper and plug in to the computer?

Check device manager under ports when you have your device unplugged probably only COM1 there.

Plug in device and refresh device manager (F5) there should now be a extra COM port.

COM4 is given as the example.   1, 2, 3, 4 and COM 1 , COM 2 etc won't work either.

So COM(number) same as it's listed in device manager.

Also unplugging the jumper from the side (so the back light is off) will give a better chance it's detected in the computer.

If that fails try install the driver from folder 1. In v1.7

Let me know how it goes.

CloudFlare changed something and screwed a bit of crap code I wrote all those years ago, I can't seem to override it in my CloudFlare account. Turning off CloudFlare at this stage is not an option, I've been ddosed before and it's not pleasant for me or my ISP.

First thing I did was a hacky fix to the existing code base, while this works V1.7 it could break again at any time. I then spent almost the whole weekend rewrite the codebase in the device from scratch in a different language, I've called this 2.0 Beta.

Both are in the normal spot on afkdata.com to download. If you decide to use the 2.0 Beta and then don't like it to go back you need to use the flasher from folder 2. In 1.7 once that's done restart the device and use the exe from folder 3.

I'm interested in feedback on the 2.0 Beta flashing.

seems to have been a little bit of movement on trade ogre recently

https://lambofactory.com is always looking for new miners

Can you help as to why this transaction is not showing in phone app?

seems your app is offchain? I sent EZT from cryptopia to the android app and it never showed up.

TXID from transfer from a friend is not showing in etherscan.io ?


how can I recover my EZT?

Yep still working through the wait list, I refuse to do pre-orders as many people here have been burnt with pre-orders....

my masternode mined 488 XCXT in one go yesterday, is this normal?

thanks

very much so, just not on many exchanges now.


i updated cagecoin.net with the exchanges that are left with cage on them, some exchanges China would be a welcome addition.

images


never quite fit me properly so only had some light use, minor scratch marks.

I was one of only three Bitcoin backers of the original NFC rings.

It has one black inlay with the Bitcoin logo and one traditional NFC inlay.

Would like to get what I paid for it, 0.3 BTC

Some orders have started to go out, I finally have a weekends to work on these.

Working on getting stock levels up before I email/twitter/reddit people, first come first serve so get in the list.      (click me link on http://afkdata.com)