 Show Posts
|
|
Pages: [1]
|
|
2
|
Economy / Computer hardware / Re: FS- Antminer D3 Nov Batch, new in hand -USA only -Free Shipping $950 or .135 BTC
|
on: November 21, 2017, 12:15:59 PM
|
Are you OK with local pickup? I have a friend near fort pierce would you be willing to meet half way?
Local pickup is preferred. I would drive to meet halfway at a location of my choosing. Would this be for BTC for USD? Up to you USD or BTC let me know. I'd rather cash, no bills larger than $20. Money is going to be used directly towards an ATV for the kid for Christmas, rather not have to wait on the transaction times of BTC currently. Unless you want to prepay with BTC, this way the transaction is completed before the trade. This I will leave up to you. What day is good for you? |
|
|
|
|
9
|
Economy / Computer hardware / Re: (WTS) Antminer D3 Nov Batch Un-opened new in box
|
on: November 15, 2017, 04:06:43 PM
|
One Antminer D3 without PSU, Bought from Bitmain directly. New, unopened in box.
It is arriving tomorrow - Will take pictures with username and date next to box when it arrives and post here.
0.17BTC Firm, free shipping to US only.
Where are you based Just south of Orlando in Florida. |
|
|
|
|
11
|
Alternate cryptocurrencies / Mining (Altcoins) / Re: [OS] nvOC easy-to-use Linux Nvidia Mining v0019
|
on: September 07, 2017, 03:58:14 AM
|
Thank you, i just tried this. My 1bash setting has -dcri 40 argument, but when i use + and - keys dcri starts changing from 70, so my setting 40 not works.
When i manualy lower it to 40 and then restart terminal miner, it again become 70
Where did you set your -dcri 40 at? Did you change any other files besides onebash? If all you changed was onebash, paste your settings here and I'll look over them for you if you'd like. (remove your wallet addresses if your paranoid) Thanks for looking I didn't change anything, only 1bash. USE_ENVIRONMENTAL_VARIBLES="NO" #YES NO
DOT_POOL_FORMAT_or_FORWARD_SLASH_POOL_FORMAT="SLASH" # DOT or SLASH # formerly ETHERMINEdotORG
CLAYMORE_VERSION="9_7" # choose 9_8 or 9_7 or 9_5 or 9_4 or 8_0
ETHMINER_or_GENOIL_or_CLAYMORE="CLAYMORE" # choose ETHMINER or GENOIL or CLAYMORE
ETH_WORKER="$WORKERNAME"
ETH_ADDRESS="xxxxxxxxxxxxxxxxxxxxxxxxxxx"
ETH_POOL="eth-eu1.nanopool.org:9999"
ETH_EXTENTION_ARGUMENTS="-dcri 40" # add any additional claymore arguments desired here Interesting. Have you tried to close and restart the miner after manually adjusting the dcri? Have you also tried to use version 9_8? |
|
|
|
|
12
|
Alternate cryptocurrencies / Mining (Altcoins) / Re: [OS] nvOC easy-to-use Linux Nvidia Mining v0019
|
on: September 07, 2017, 12:51:19 AM
|
Thank you, i just tried this. My 1bash setting has -dcri 40 argument, but when i use + and - keys dcri starts changing from 70, so my setting 40 not works.
When i manualy lower it to 40 and then restart terminal miner, it again become 70
Where did you set your -dcri 40 at? Did you change any other files besides onebash? If all you changed was onebash, paste your settings here and I'll look over them for you if you'd like. (remove your wallet addresses if your paranoid) |
|
|
|
|
13
|
Alternate cryptocurrencies / Mining (Altcoins) / Re: [OS] nvOC easy-to-use Linux Nvidia Mining v0019
|
on: September 06, 2017, 03:06:49 PM
|
I'm not by my rig at the moment is watchdog auto enabled in 19? Anything one could do to mess up watchdog and it will restart the rig by error?
Has there been a consensus on an ideal GPU operating temp for mining -- more specifically for 1080 ti / 1070
My rigs are cooled my outdoor air so . . massive fluctuation in temps compared with temp controlled rig rooms
Currently I am using the standard 75% fan speed
In FL I have my 1070 rigs outside in the garage with a fan blowing threw them to provide ambient air so they do not get heat-soaked. Temps stay at or below 65c with max fan speed during the day at 50%. |
|
|
|
|
14
|
Alternate cryptocurrencies / Mining (Altcoins) / Re: [OS] nvOC easy-to-use Linux Nvidia Mining v0019
|
on: September 06, 2017, 01:41:10 PM
|
Hi, i just upgraded from 0018 to 0019 and my 1060 3g with same settings (cc100, mc800, pl75, Dual ETH_SC, dcri 40) shows 3-2 Mh less in 0019 then 0018. What is wrong, may be some additional settings?   Sometimes a new claymore version will do worse with specific GPUs. My guess is thats what is happening. Try changing: to Thanks it helps. But only if i am mining ETH solo. When i switch to dual ETH_SC claymore 9_7 the hashrate ETH goes down, but SC goes up. I noticed if i change argument -dcri nothing happens, doesnt matter do i do -dcri 0, -dcri 40 or -dcri 100. Is it possible something wrong with 2unix or 3main setings becase -dcri argument doesn't Influence Try manually switching dual mining off on one of the cards after it has started by pressing a number 0-9 (ie.e GPU0, GPU1, GPU2). Pressing a number once to turn the mining for that GPU off, press it again to go into ETH only, check numbers, and you can resume dual mining by pressing the same number once more (you will see text of what state you are in while your doing this in terminal). If it is caused by the dual mining, try to manually lower the DCRI in the terminal by using the - key. ( + key = increased hash rate of second coin, - key = lower hashrate of second coin) |
|
|
|
|
15
|
Alternate cryptocurrencies / Mining (Altcoins) / Re: [OS] nvOC easy-to-use Linux Nvidia Mining v0019
|
on: September 06, 2017, 01:31:53 PM
|
Mate, that is a very simple DIY stuff, for which you don't need to wait until next release. Just follow this guide and try v10, you can simply switch back by renaming folder names. Download the Linux version on rig from this link : https://drive.google.com/drive/folders/0B69wv2iqszefdFZUV2toUG5HdlUextract it (right click extract here) Go to /home/m1/eth (can do it using GUI) rename the 9_8 to 9_8_xx copy the latest claymore folder from downloads and paste it in the above eth folder and rename it to 9_8. It should work normally (this is the easiest work around, you don't need to edit any 1bash or 3main). I've seen a little increase in dual mining lbc hashrates. Hope it helps  Thank you! I was pretty sure the folder would have to be coded in, but never thought about using an existing folder as a temp solution!! Is it only an increase for AMD lbc hr or also nvidia? |
|
|
|
|
