 Show Posts
|
|
Pages: [1] 2 3 »
|
|
The software sees 2 different GPUs on the same PCI Bus, the first one is an RX 570 8Gb and it is supposed to be on PCI Bus 13, is it a driver problem (18.5.1) or the miner software is bugged? Also the hashrate report shows like it was 2 GPUs, I mean 850 H/s x2...
[2018-10-22 15:23:58] GPU1: Radeon RX 580 Series [ellesmere] [8192 MB][Intensity 59.0][W: 8][T: 2][K: 1][BUS: 2]
[2018-10-22 15:23:58] GPU2: Radeon RX 580 Series [ellesmere] [4096 MB][Intensity 59.0][W: 8][T: 2][K: 1][BUS: 2]
GPU1 : 1712 H/s [T: 74c, RPM: 0, CC: 1220 MHz, MC: 2010 MHz][BUS:2]
|
|
|
|
Does anyone know which pool is the best to mine for that coin. I'm using yiipmp, but I'm not getting the amount of calculated coins per day. I should be getting just over 200 a day, but I'm getting more like 110 even though my hashrate is spot on from the Raven coin calculator. http://ravencalc.xyz/i use https://minepool.com/ |
|
|
|
Damn one of my cards is dying out on this new algo, otherwise, the rest of my rx580 are hashing 880h/s with 1140/2200 900 voltage.
I noticed this today ... Kinda strange, not sure what's up with it. Thread 4 and 5 are slightly lower, because that's the card with the dummy hdmi in it, but thread 12 is way lower than normal. Not sure why that is. Something else to note ... With the old version of XMR STAK, I never got much above 11,500 h/s and all cards were looking normal as far as individual hashrate. I guess you have 12 GPUs (0-11 thread) and the thread 12 is your CPU... |
|
|
|
I try to connect to Cryptonight server, but I always get socket error, I've tried different servers, same result... xmr-stak SOCKET ERROR - [europe.cryptonight-hub.miningpoolhub.com:17024] 5468:error:2006A066:BIO routines:BIO_get_host_ip:bad hostname lookup:.\crypto\bio\b_sock.c:146:host=europe.cryptonight-hub.miningpoolhub.com SOCKET ERROR - [europe.cryptonight-hub.miningpoolhub.com:20580] 6132:error:2006A066:BIO routines:BIO_get_host_ip:bad hostname lookup:.\crypto\bio\b_sock.c:146:host=europe.cryptonight-hub.miningpoolhub.com SOCKET ERROR - [us-east.cryptonight-hub.miningpoolhub.com:20580] 5048:error:2006A066:BIO routines:BIO_get_host_ip:bad hostname lookup:.\crypto\bio\b_sock.c:146:host=us-east.cryptonight-hub.miningpoolhub.com I don't use xmr-stak, but try using " stratum+tcp://us-east.cryptonight-hub.miningpoolhub.com thanks, but it looks like all cryptonight servers are down, ping request could not find none of the crypto servers... |
|
|
|
How I can flash AMD RX Card with Atiflash with more than 10 GPU of different type ?
Using the cli you can set the GPU ID from 0 to 9, how I can flash the 10-11 GPU ?
thx
Atiflash only supports one digit numbers, so turn off half the cards, then flash the other half... |
|
|
|
I try to connect to Cryptonight server, but I always get socket error, I've tried different servers, same result... xmr-stak SOCKET ERROR - [europe.cryptonight-hub.miningpoolhub.com:17024] 5468:error:2006A066:BIO routines:BIO_get_host_ip:bad hostname lookup:.\crypto\bio\b_sock.c:146:host=europe.cryptonight-hub.miningpoolhub.com SOCKET ERROR - [europe.cryptonight-hub.miningpoolhub.com:20580] 6132:error:2006A066:BIO routines:BIO_get_host_ip:bad hostname lookup:.\crypto\bio\b_sock.c:146:host=europe.cryptonight-hub.miningpoolhub.com SOCKET ERROR - [us-east.cryptonight-hub.miningpoolhub.com:20580] 5048:error:2006A066:BIO routines:BIO_get_host_ip:bad hostname lookup:.\crypto\bio\b_sock.c:146:host=us-east.cryptonight-hub.miningpoolhub.com |
|
|
|
|
Let's get ready to rumble...
|
|
|
|
r7 370 2g can be mining eth with this program?
No, to mine ETH you need at least 3GB VRAM videocard... |
|
|
|
|
I've tried the 2.4 on a 11 GPU rig (9xRX580 4Gb 1xRX570 4Gb 1xRX480 8Gb), I got steady 325.xxx Mh/s, it's more consistent than Claymore, with Claymore I get 290-322...
Waiting for the dual mining version...
|
|
|
|
You've bought 12 RX cards and don't even know how to set them up properly??? Ignorance is bless... https://mining.help/ |
|
|
|
From the PSU you power the MOBO the GPUs and the risers too, at the top of the GPUs you plug the 6+2 pin PCIe connectors and power the risers with the other 6-pin connector, if you can reach to them, or with the 4-pin Molex connectors, max. 2 per cable!! If its possible don't use the Sata-6 pin adapters to power the risers or max. 1 per cable... |
|
|
|
I’ve set up my mining rig with 5 RX570s on a Biostar TB-250 BTC Pro and started on Monero on Nanopool.
I averaged 150 H/s per GPU mining Monero without modding and tweaking anything in the GPU. People are getting around 600-700 H/s. The risers are working normally and I haven’t had issues with them. I’m running Windows 10 Enterprise and installed the AMD Adrenaline driver. Since I couldn’t make anything on Monero, I started up Nicehash and have been doing nicely. I’m getting the expected hashrates with Nicehash but with XMR-stak, it’s way lower. Without doing any modding or tweaking, what can I do to raise my hash rate?
Please post any information you need to determine what could be causing the issue.
Beside the tweakings, you can try to switch in the Adrenaline driver to compute mode at Gaming/Global settings/Gpu workload, if it doesn't help, try the AMD blockchain driver after uninstalling the Adrenaline with DDU... |
|
|
|
Should I switch BIOS to silent on my cards before HEX flashing timings?
Hell what a brilliant thread.... One question how do I know which bios is which on the RX570 .... I believe the silent one cannot be flash as a precautionary measure. ..Hence my question which is the starting point .....closest to front of the card or the position towards the middle. My Rx580 seems fine ...just need to sort the Sapphire Rx570 with bios switch. You can and you should flash the silent BIOS which is closest to the front panel with the connectors... don't flash the other BIOS... |
|
|
|
Thanks for the fast reply.
Would u consider 'ASUS Radeon RX 580 4GB Dual' and 'Sapphire 570 4gb nitro+' to mine at the same speed if both have samsung memory?
I have an Asus Radeon RX 580 8GB Dual with Hynix memory and a Sapphire Nitro+ RX 570 4GB with Elpida memory, after BIOS mod and overclock/undervolt I get the same speed on both with Claymore (30.1 Mh/s), both draw 105W from the wall, the only difference is that the Sapphire runs at 37C while the Asus at 55C... |
|
|
|
Hi i have two identical Sapphire 580 RX Nitro + 8GB with Samsung memory in a rig with Asus Prime Z270-P Mobo I have flashed their bioses with an optimised one and each one of them individually gets 30.8 Mh/s but when both are together one always underperforms and drops to 22Mh/s. http://prntscr.com/hubno5 <--- screenshot I tried troubleshooting this by switching the connectors and raisers to each card and also switching their positions on the mobo but each of them in any combination individually gets the max rate but when both together one drops hash rates from 30.8 to 22! Any idea what could be the problem? I plan on getting 4 more of those and i am afraid if i dont know whats causing this i am about to be in big trouble when i have to run 6 of them and get several of them underperforming. Regards, Atanas Have you disabled CrossfireX for them? that could cause hashrate drop for 2 GPUs... |
|
|
|
Getting 25.3 Mh/s ETH, on RX570: running on 1150 / 2000, -93 mV, PowerLimit -15%
Is it the best what I can get on DAG 160?
Anyone has a better result on RX570 / RX580 ?
Thanks
*at Polaris OneClickPatch BIOS Mod
it should be higher for an RX570, which driver do you have? Use the Aug23 Blockchain driver or get the new Adrenalin and switch to "Compute" mode in the AMD global settings... |
|
|
|
Hello everybody.I am new here and have some problems with the new miner i made. So i mine on ethermine with claymore and for a while everything went well, and decided to make a separate miner.I bought all the neccesarry equipment motherboard, cpu etc. and after puting it together, i went to a friend to help me with all the necessary instalations for the operating system.We installed windows 7 with all the necessary drivers.I copied the claymoreminer folder with all the settings from my other HDD to the new SSD. When i try to mine ETH I get this message in the claymoreminer: ETH:Stratum - connecting to 'eu1.ethermine.org' <93.115.31.250> port 4444 Stratum - Cannot connect to eu1.ethermine.org:4444 Stratum - Failed to connect, retry in 20 sec.... I tried to change address to US and Asia, and also change the port to 14444, 3333 etc.And everything gives the same result. Tried to connect to nanopool and i get the same error as on ethermine. I mention that i mined with no problem on the other miner. I have a screenshot of this problem. https://imgur.com/1bogV4UAlso i just checked right now and i can mine Eth Classic on ethermine , it connects to pool.I just can't understand why i can connect to ethermine for ETC but not for ETH. I did not had this problem before. What is wrong? I think it is something about your config, try to add -allpools 1 or -eworker whatevername options may help... How do i do that? Hei guys can someone help me with this problem please? I tried all the servers EU, US & Asia and found the connection to be erratic. It would not connect to the US or Asia servers and would sometimes connect to the EU server. I think another pool is probably in order, try Mining Pool Hub. This is the .bat configuration I got working (sometimes). set GPU_FORCE_64BIT_PTR 0
set GPU_MAX_HEAP_SIZE 100
set GPU_USE_SYNC_OBJECTS 1
set GPU_SINGLE_ALLOC_PERCENT 100
set GPU_MAX_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool eu1.ethermine.org:14444 -ewal YOUR_ETHER_ADDRESS -epsw x
Replace "YOUR_ETHER_ADDRESS" with your Ethereum wallet address, if you don't have, you can get one here https://www.myetherwallet.com/ |
|
|
|
|
