Old problem is still there, but we have an additional problem, In the overclock config on the web interface, the temp. is set to 50 degrees and the min. fan speed to 90%. The rig doesn't do anywhing with these settings any more. The cards are 65 degrees and the fans are running at 43%.

Is there some way to reset everyting ? Its going from bad to worse

I need some help, All of a sudden my 4 card (1070 + 3 x 1060) rig changed to a 3 card rig (1070 + 2 x 1060)

Strange thing is, lspci shows :

00:1f.6 Ethernet controller: Intel Corporation Ethernet Connection (2) I219-V (rev 31)
01:00.0 VGA compatible controller: NVIDIA Corporation Device 1b81 (rev a1)
01:00.1 Audio device: NVIDIA Corporation Device 10f0 (rev a1)
02:00.0 VGA compatible controller: NVIDIA Corporation Device 1b84 (rev a1)
02:00.1 Audio device: NVIDIA Corporation Device 10f0 (rev a1)
03:00.0 VGA compatible controller: NVIDIA Corporation Device 1b84 (rev a1)
03:00.1 Audio device: NVIDIA Corporation Device 10f0 (rev a1)
04:00.0 VGA compatible controller: NVIDIA Corporation Device 1b84 (rev a1)
04:00.1 Audio device: NVIDIA Corporation Device 10f0 (rev a1)
06:00.0 PCI bridge: ASMedia Technology Inc. Device 1187

but nvidia-smi shows :

Mon May 28 21:17:22 2018
+-----------------------------------------------------------------------------+
| NVIDIA-SMI 384.59                 Driver Version: 384.59                    |
|-------------------------------+----------------------+----------------------+
| GPU  Name        Persistence-M| Bus-Id        Disp.A | Volatile Uncorr. ECC |
| Fan  Temp  Perf  Pwr:Usage/Cap|         Memory-Usage | GPU-Util  Compute M. |
|===============================+======================+======================|
|   0  GeForce GTX 1070    On   | 00000000:01:00.0 Off |                  N/A |
|  0%   60C    P2   115W / 115W |    937MiB /  8112MiB |    100%      Default |
+-------------------------------+----------------------+----------------------+
|   1  GeForce GTX 106...  On   | 00000000:02:00.0 Off |                  N/A |
| 25%   47C    P2    85W /  60W |    907MiB /  3013MiB |    100%      Default |
+-------------------------------+----------------------+----------------------+
|   2  GeForce GTX 106...  On   | 00000000:03:00.0 Off |                  N/A |
| 27%   50C    P2    84W /  60W |    907MiB /  3013MiB |    100%      Default |
+-------------------------------+----------------------+----------------------+

+-----------------------------------------------------------------------------+
| Processes:                                                       GPU Memory |
|  GPU       PID  Type  Process name                               Usage      |
|=============================================================================|
|    0      2757    C   /root/miner/dstm-v0.6.1/zm                     927MiB |
|    1      2757    C   /root/miner/dstm-v0.6.1/zm                     897MiB |
|    2      2757    C   /root/miner/dstm-v0.6.1/zm                     897MiB |
+-----------------------------------------------------------------------------+

any idea what this might be ?

Will you be adding more Cryptonight v7 coins (like : Graft, Intense, Masari Fornero or Stellite) ? Keep up the good work

Not this, I've made new transaction to new MN2 address en used this masternode output and tx information to use on the masternode. Same problem, the new one just works find, the running one stopped to work. The debug states "not capable masternode: Could not find suitable coins!" and on the TGAO Wallet the error is stil the same "Error : Could not allocate vin". After 12 hours both ip addresses are not in the masternode list and clicked start all, same problem.

I've tried adding stacking=0 to the ReliefProject.conf and restart. Dosn't change a thing. The windows wallet isn't locked and not enrypted (yes I know ).

I'm doing something wrong, but I have no idea what it is. Help is very much apriciated.

The strrage thing is that the 1st masternode doesn't work anymore and the new 2nd one works just fine. There is nothing changed with the 1st nodes, could the problem be that the original TX key isn't up to date anymore because I have made both transfers to my original wallet address and NOT a separate address ?

Can you run 2 masternodes (cold, so with linux VPS) from one windows wallet ?

Already I have one masternode, It runs fine. And today I've added a new node (different VPS server). Used the same staps (beginning of this posting). And the new node starts perfect.

But the first one now seems to be "Not in the masternode list" according to the Windows wallet. At VPS level the debug command (reliefd masternode debug) shows : "not capable masternode: Could not find suitable coins!"

In the wallet there is more than 100.000 coins so the coins are there.

What did I do wrong ?

Had the same, but with 517 coins. I've used in the NEW windows wallet (so v0.12.5.1-b31d6d5) the steps below

1. Rescan blockchain files
2. Rebuild Index
3. Recover transactions 1

And recovered my 517 coins. Perhaps this will help you to recover you're 2000 coins ?

For the last couple of days I've been searching for an autoexchange with multi coin pool like MiningPoolHub and ZergPool with good Cryptonight support. We now have so many Coins with Cryptonight it's a lot of work every time to change to a different coin on a different pool.

I'm sure there is some autoexchange pool with multi cryptonight coin pool, but I can't seem to find. Can somebody point me in the right direction ?

In nobody mining eternity ? we're stuck at block 307021 already day and a half

Why does my Avast antivirus think the new wallet (v 1.1.2.0) is infected with Win64:Malware-gen. ? Or is the new wallet ok ?

After folowing the instructions to make a masternode (VPS + Windows) I'm wondering if mine is working fine. I've noticed the folowing things :

1. After starting the windows wallet (v1.0.5.0-ReliefV2) it takes a while before the masternode tab reports "Masternode is running". When the wallet is first fully synced the status is "Masternode not in list"
2. Useing the "reliefd masternode status" command on the VPS, it reports back ==>  "notCapableReason" : "Could not find suitable coins!",but "reliefd masternode debug" reports "Masternode started remotely". Useing the "reliefd getbalance" command on the VPS the service reports "0.0000"
3. The payout of the masternode is not everyday. I've started mine (209.250.243.192) on the 7th of april and received one payment at the 8th of april (711,433xx TGAO), but now its 3 days later, nothing else is received in the wallet.

So this is makeing me a not quite sure everything is going ok. Is this normal for a TGOA masternode ? Any idea's ?

<<update>>

4. Just received another payment, but it says "staking" so not masternode. It seems I'm doing something wrong....

For the last couple of days I've been testing the --cpu-affinity option with my dual opteron 6376 trying to get cpuminer to use just 4 threads (14/15 and 30/31) instead of everything or the first one.

For some reason the --cpu-affinity option is noticed by both programs (using --cpu-affinity 6 or --cpu-affinity 0x6 for testing) but in all of the cases the program uses all cores or using the -t 2 option core 0 and core 1. But this is not what I want.

I'm sure I'm doing something wrong, but no idea what. Should the --cpu-affinity option go with another option ?

This is my commandline :
./cpuminer -a yescrypt -o stratum+tcp://hub.miningpoolhub.com:17021 -u <my_mph_username> -p d=10

I'm using Ubuntu 16.04 LTS and this is updated useing the apt-get update -y && apt-get upgrade -y. So this shoud be just fine. Any suggestions ?

It takes a long time, after waiting 8 days there is finaly the first payment. So just sit down and wait.......

Is there a howto somewhere ? Is there a linux VPS intallation ? or just Windows Masternode ?

No idea, but looking at the blockchain explorer, the last block 301946 was mined at 2018-04-01 03:36:44 and thats it. Does anybody have any idea whats going on ?

Avast warns me for a Win32 Malware gen with the new wallet. Is the https://github.com/YiDeveloper/Yi/releases/tag/v.2.0-win safe ?

Any idea when or if bminer will be added ? https://bitcointalk.org/index.php?topic=2519271.0

I don't have these problems with this pool, been mining for a couple of days and yes, the payout is slow. But its there, it takes a lot of time for them to process payment (up to 24 hrs).

Is anybody working on getting this coin to an exchange ?

Ok, thanks. I'll try your suggestions and lets hope this will help. I'm trying to set the difficulty as high as possible so the traffic will be limited.

The hashrate is 900 H/s so to the diff should be between 40000 to 80000 ?

Now for a couple of days I've been using XMR-Stak with my dual core DL385P and it sees to work just fine. Just one small problem, every time the difficulty gets above 32000 the miner takes to long to give an answer to the pool and the connection get dropped. The miner comes back at a lower difficulty and in time it raises up to 32000 again. The hole cycle starts again (connection drop, etc etc)

Is there a trick or option to tell XMR-Stak never to go higher than 30000 ?