Show Posts
|
Pages: [1] 2 »
|
Hello Patrik,
could you please add the very very new Lyra2Z WIN miner TeamRedMiner v0.3.2 ? It is working properly but i would like to see more info in AM(i guess they need to add reports etc. too).
Thank you!
|
|
|
Hi, first of all, thanks for WIN version.
I am trying to run miner with custom settings "D" because otherwise i get error during startup due to integrated GPU at position 0..therefore i tried with "-d 1,2,3,4,5,6" but so far is not working.
> Team Red Miner version 0.3.2 > [2018-09-30 11:39:44] Failed to initialize device number 0. #d0 in this case only to show up the error, this device is not used for mining > [2018-09-30 11:39:44] Device number ## is out of range.
FIXED: With "--platform=1 -d 0,1,2,3,4,5"
Setup: Adrenaline 18.4.1/Win10 1803.
Hashrate: Rigs are all properly set up to be stable and have lower possible power draw(rougly clck 1170Mhz/2100Mhz). 6GPU rigs Vega56 - On GRAFT(MoneroV7) doing cca 11,1KHs on Lyra2Z cca 35,2Mhs RX570 4G - On GRAFT(MoneroV7) doing cca 5,32KHs on Lyra2Z cca 15,1Mhs RX580 4G - On GRAFT(MoneroV7) doing cca 5,35KHs on Lyra2Z cca ???Mhs - This one little b* is not willing to cooperate (still runs old setup) but i guess the results will be very similar to RX 570 4GB - Will try 580 8G later next week or so)
Thanks a lot for that!
|
|
|
ah, ok, sorry thought you're trying to manage overclocking with AM and Afterburner, I'm not an AMD person btw, only have 2 RX470 vs tens of NV cards (though, my AB can set different clocks between the 2, I did let AB manage customized Fan control curves and not let AM do anything regarding GPU controls). Apart from modding BIOS timings, I left the cards with their default memclock of 1650 when booting up, and only set clock to 2000 via AB startup profile locally (not remote), gets 29MH/s each on ETH (both with Hynix VRAM) so I guess not too bad. Point being though, maybe try other OC tools like OverDriveNT, I suspect something else is causing the sync clocks rather than AM in your scenario. [/quote] Uhm, yes, it might helped to use overdrive, but i need to find solution within current setup, AM+Afterburner is nice combo which suits well..its just something has to be fixed within the settings, i mean..the point of AM was to manage all in one and thats what i aim for. Thanks, hopefully this will get answered by support
|
|
|
Hello all, I am coming to you with a question in regards to GPU clocking. I just noticed that when we use Afterburner our GPU will set all on the same settings, even though the "synchronize all" is turned off. Our rigs are each specifically tuned with own BIOS (AMD part) and has different clocking. But since we use AM and especially MSI Afterburner it use the "memory clock" of the first GPU regardless. How can this be turned off? Also there is this issue that even the "memory clock" is not shown in the GPU Settings of AM. So even if i wanted to set that differently for each GPU i am not able to. Clocks are working if i try it on testrig where only one card is able to work, it gets right clocks and has no issue. Thank you very much, hopefully someone is able to respond. In parallel i will try info@... Have a nice weekend! https://support.awesomeminer.com/support/solutions/articles/35000086015-gpu-overclockingCheck the section on "Clocking Profile Groups", this allows you to set clocks in a mixed GPU system and apply clocking per GPU / group of GPUs Hi, i just thought i made myself clear enough, but this may help a bit more, please see: 1. I am not clocking up the system with AM. Clocks are set via BIOS directly. Only FANs are set and that is related to "Miner template" not GPU. 2. I already run through various videos, also official documentation, and did some re-installation of system to start from blank. None of this helped. 3. Here are screens just so you have the full picture: You can see there that there is only one clocking profile with FANs only set - that is working correctly. Also you can see that the memory clocks are available, means they can be read. One GPU is missing, because it is disconnected now, but it would show the same memory clock - HOWEVER GPU Z default clock(out of bios) is set to 1950Mhz!! Only somehow it is re-clocked to 2100 with others. As stated, on SINGLE GPU TEST RIG this issue is not happening. Hope this helps. Thanks for the suggestion anyways!
|
|
|
Hello all, I am coming to you with a question in regards to GPU clocking. I just noticed that when we use Afterburner our GPU will set all on the same settings, even though the "synchronize all" is turned off. Our rigs are each specifically tuned with own BIOS (AMD part) and has different clocking. But since we use AM and especially MSI Afterburner it use the "memory clock" of the first GPU regardless. How can this be turned off? Also there is this issue that even the "memory clock" is not shown in the GPU Settings of AM. So even if i wanted to set that differently for each GPU i am not able to. Clocks are working if i try it on testrig where only one card is able to work, it gets right clocks and has no issue. Thank you very much, hopefully someone is able to respond. In parallel i will try info@... Have a nice weekend!
|
|
|
Hi all,
Please, How to setup the msi afterburner remote server if logging into domain? I am having issues using only username or domain\username.. Not sure where the error is coming from. Folder is good and i even created admin user only for that and it stipp not succesfull.
Thanks!
|
|
|
UPDATE TODAY!!!!! 2.84 works on new windows!!!! WOHOOO THAAANKS
|
|
|
Anybody got a solution on that ? No i dont want to go back because at one point i will need to update.
|
|
|
SAME It created errors in Event Viewer /Adm Events Event ID: 1000 Exception code: 0xc0000005 Error code: 0x00001eb7 Everytime you try to run it through CLI
|
|
|
I guess this will be my last try, please check first comment for more info on the meaning of E388
|
|
|
Hi, pretty much subject sums it up, after FORCED (even had it disabled in registry, set metered wifi, services disabled) our rigs got update, one after another just this weekend. That is not that bad as the fact i have now no chance to run ATIFLASH via CLI nor GUI.
It created errors in Event Viewer /Adm Events Event ID: 1000 Exception code: 0xc0000005 Error code: 0x00001eb7
What in the hell should i do to fix this ? Could anybody provide an advice? THANKS A LOT!!
|
|
|
A try for a bump, still looking for thr correct bios
|
|
|
Again a Bump still looking for the stock bios.
|
|
|
Hi nitrobg,
Thanks for the offer i have got this one. I got a more so if someone is looking i can offer some too. I really only need that one.
|
|
|
Hi all,
sorry i got sick and was laying for few days.
@Dzeronimo: E388 i guess is a part of GPU "series" numbering or so, these were delivered to use late 2017. Nowadays we get E387, its is part of P/N number.
@jmigdlc99/jillscarbrough: Why not backup? Its simple, at the time we got the i forced few of GPUs with other versions, it has no bad effect, but if you are going to give the product back due to HW errors ( normal warranty procedure ) they can easily find out if was BIOSed, because the P/N will not fit. Can be seen on the card label - middle part.
So the only reason to have it back at E388 is in case we will need to claim the warranty of product, to be on the safe side.
Thanks
|
|
|
BUMP
|
|
|
Hi, does anybody have version E388 for this particular card ? I have got E353, but i need E388 to reflash. Thank you
The marking can be found in GPUZ on "Graphic Card" tab, DEVICE ID: mine is now for example (other card) 1002 67DF - 1DA2 E366 so the ending there is what i am looking for.
A stock bios of E388 version RX 570 Pulse 4GB Elpida E388
|
|
|
|