 Show Posts
|
|
Pages: [1]
|
Anybody else getting a big ETH hash rate drop when dual mining Verge? I have played around with DCRI and it doesn't seem to effect the ETH hash rate much but I took a 26 mh/s hit when I started to dual mine Verge?
Same problem, dual mining doesn't affect my reported ETH hash rate but at my current speed of 480 MH/s reported I've only been getting 350 MH/s average for the last 24 hours. I had my DCRI at 20, dropped it down to 10 and we'll see how it does. I'll add more ram tomorrow to see if that could be the issue. Likely PSU or config issues. I rebooted and my ETH hash went back to normal. I had to play a little with ETHI and DCRI but now Im back at 378 MH/S for ETH and about 17500 MH/S for blake2s |
|
|
|
If you've got connection problems on antminepool try this:
XVG blake2s: added new mining port 9009. Please move to the new one. The 9008 is full
For example:
ETH: ethermine.org
XVG: antminepool
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal 0x54abE209A969A9f3B0BF07D54647b786F09753b4.W1RX480 -epsw x -dpool stratum+tcp://s.antminepool.com:9009 -dwal D9dMdBssQZRDueBzVeRUsEFzmA5smW1kQA -dcoin blake2s -dpsw c=XVG -dcri 44
How to name my workers? not working for antmine Ahashpool has been working great try them out. You get paid in BTC too else you want to hold VERGE |
|
|
|
Anybody else getting a big ETH hash rate drop when dual mining Verge? I have played around with DCRI and it doesn't seem to effect the ETH hash rate much but I took a 26 mh/s hit when I started to dual mine Verge?
Same problem, dual mining doesn't affect my reported ETH hash rate but at my current speed of 480 MH/s reported I've only been getting 350 MH/s average for the last 24 hours. I had my DCRI at 20, dropped it down to 10 and we'll see how it does. I'll add more ram tomorrow to see if that could be the issue. My reported in Claymore dropped which is turn drops the pool side too. According the usage my 8gb ram and virtual is fine... I went from 377mh/s to 350mh/s in claymore for eth when dual mining.. |
|
|
|
|
Anybody else getting a big ETH hash rate drop when dual mining Verge? I have played around with DCRI and it doesn't seem to effect the ETH hash rate much but I took a 26 mh/s hit when I started to dual mine Verge?
|
|
|
|
TIMEOUT 15
setx GPU_FORCE_64BIT_PTR 1
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool us1.ethermine.org:4444 -ewal yourwallet -epsw x -epool eu2.ethermine.org:4444 -ewal yourwallet -epsw x -dpool stratum+tcp://blake2s.mine.ahashpool.com:5766 -dwal yourBTCwallet -dpsw c=BTC -dcoin blake2s -mode 0 -allcoins 1 -r 1 -dbg -1 -lidag 1 -tstop 80 -mport -3333 -platform 1 -ethi 16 -dcri 50 -allpools 1 This worked thanks. I do notice I am taking a 20-25mh/s hit on ETH to mine Verge. I tried dropping DCRI to 44 and they brings it down to a 20 mh/s hit on ETH. I thought the new 11.0 for others was mining ETH at the same rate while adding an ALT coin? |
|
|
|
Use ahashpool, there isnt problems.
Use ahashpool, there isnt problems.
I am trying to get the new 11.0 claymore working with ahashpool that you recommended but it won't recognize the options that ahashpool wants. Example- <WALLET_ADDRESS> [-p <OPTIONS>] ahashpool says you need C=BTC and you can add your worker ID=name here Claymore kicks out [-p ID=name C=BTC] If you don't mind sharing your BAT file for Ahashpool? Thanks |
|
|
|
Yes, whats the problem? I don't think anyone here wants verge. Everyone wants BTC.
Yes I agree I meant easier for the other guy who was trying to use his bittrex XVG address. Everyone has a BTC address and ahashpool makes that easy |
|
|
|
Use ahashpool, there isnt problems.
ahashpool uses BTC addresses |
|
|
|
I'm having an issue with 2.6. Basically when the watchdog detects a GPU thread that isn't responding the whole system locks up when the restart occurs. No issues on Claymore. Has anyone heard of this issue?
yes this happened on devfee for me |
|
|
|
phoenix crashed at 10.5 hrs so that why I used that mark LOL
What happens is a GPU hangs and drops to 0 in DEVFEE then when it trys to go back to regular it doesn't recognize it needs to restart and it will get stuck in DEVFEE and issue incorrect shares by all GPUs. Its happened at 10.5 hrs, its happened at 1.5 hrs and even at like 4 hours. Otherwise I haven't had any issues with phoenix it's been stable if I didn't have the DEVFEE issue.
I forgot to ask- what version are you running? I tried 2.4, 2.5 and 2.6B. I was having the best luck on 2.4 but all 3 do the DEVFEE issue for me unfortunately. I tried 2.6 today thinking it might not happen but it did  |
|
|
|
|
phoenix crashed at 10.5 hrs so that why I used that mark LOL
What happens is a GPU hangs and drops to 0 in DEVFEE then when it trys to go back to regular it doesn't recognize it needs to restart and it will get stuck in DEVFEE and issue incorrect shares by all GPUs. Its happened at 10.5 hrs, its happened at 1.5 hrs and even at like 4 hours. Otherwise I haven't had any issues with phoenix it's been stable if I didn't have the DEVFEE issue.
|
|
|
|
pool average fluctuates a lot but overall average is about 1-2% better on phoenix than running claymore, hashrate doesnt matter, accepted shares do, which is why i based my comparison on that number.
other differences are that phoenix doesnt have any fan control or clock/voltage modification where claymore does, and on my rig, even though i see more hashrate with pheonix, i see 10-20W more power consumption as well.
Over a 10 hour period I had 100 more shares on Phoenix. Granted that can be luck or it can be the program. I get about 5 more hash then claymore. Claymores reported is also 2 m/hs lower at the pool then what is reported in the program. Phoenix follows the reported on the miner right through to the pool. However I keep getting devfee errors and have to resort back to claymore until it's resolved. It keeps hanging up after a couple of ETH shares are found on Phoenix. |
|
|
|
The dev is working those feature into the program but for now, use overdriveNtool by the guy on guru3d
Works great for all overclocking, undervolting and fan control. I mod all my bios with Polaris 1.6 but if I need to tweak anything after I use overdriveNtool
Could you please share a simple guide on how to undervolt with this tool mate? I don't want to mess up my cards  I don't know if I should even do it, since for the first two weeks my rig is finally stable *fingers crossed* and I don't know if that would cause any instability, that's why I'm asking. It just much simple with those commands to do it and not go in-depth, that's why I asked, I don't mind waiting tho. Electricity is 0.06usd, so 100-150w won't cause me to lose much of the profit. It just bugs me, that the cards are getting hot and the fans, therefore, are working at 60%, producing a lot of noise. You want to focus on P6 and P7 (this is your core clock and core voltage) and then P3 (memory clock and voltage). You need to make P6 voltage slightly higher then P7. You can carry the P6 voltage all the way back to P2 for the core. I don't adjust the memory voltage only the memory clock in the middle of the program under p3 (p1 to p3 columns). I believe it helps maintain stability and you'd only save a couple watts at most by undervolting the memory voltage. Most of your savings will be the core clock and core voltage in p6 and p7 on the left side of the tool. Since the gpu runs 100% almost all of the time for utilization the most relevant field is p7 core clock and p7 voltage. |
|
|
|
61hr tests on each claymore and Phoenix. on nanopool mining ETH
Claymore v10.0
4744 shares accepted
0 rejected
Phoenix 2.5d
4815 shares accepted
0 rejected
1.2% stales
this shows that over these two 61hr periods, Phoenix submitted 1.5% more shares. but phoenix also had 1.2% stales. I'm not sure how to compare this with claymore since claymore's program doesnt report stales.
Set up one machine to ethermine and one to nanopool and see what stale shares are reported? I'm only familiar with ethermine and they report stale shares which are usually slightly higher then whats reported by phoenix because phoenix is a calculated number. |
|
|
|
The Program itself its pretty simple, load the GUI, enter your settings onto one card, click to save that as a profile, that will create a config file right in the same folder, you can go in there and make other profiles with copy and paste and edit them faster then in the GUI, but either way woek, edit config file or GUI. That's how you make any number of profiles you want to call with the -pX function. You can have a profile for each card in your rig if you want. These are my two profiles in this one rig, the voltages need a little touchup, kind of high: [Profile_0]
Name=570
GPU_P0=300;750
GPU_P1=588;765
GPU_P2=976;956
GPU_P3=1065;950
GPU_P4=1130;950
GPU_P5=1192;950
GPU_P6=1233;950
GPU_P7=1268;950
Mem_P0=300;750
Mem_P1=1000;800
Mem_P2=2200;900
Fan_Min=750
Fan_Max=3000
Fan_Target=70
Fan_Acoustic=910
Power_Temp=90
Power_Target=0
[Profile_1]
Name=580
GPU_P0=300;750
GPU_P1=600;769
GPU_P2=918;893
GPU_P3=1167;1050
GPU_P4=1239;1050
GPU_P5=1282;1050
GPU_P6=1326;1050
GPU_P7=1366;1050
Mem_P0=300;750
Mem_P1=1000;800
Mem_P2=2250;900
Fan_Min=1125
Fan_Max=3500
Fan_Target=75
Fan_Acoustic=918
Power_Temp=90
Power_Target=0 And I have found that these 'hold' better then using watt man, afterburner, claymore command line, sapphire, any of them. Really rock solid. If I could use Phoenix Miner with geth I would be getting 32 and 34.5 MHS on the 570s and 580s respectively but nope, I am suffering with Claymore still. haha. I haven't put overdriveNtool into the BAT file but it appears pretty simple. I should... Occasionally the unit will blink and then I have to check the profiles. I do need to rename them because I have tried to be specific so I know which card is which in my profile but it would be a much longer bat file. I guess that doesn't matter? |
|
|
|
|
The dev is working those feature into the program but for now use overdriveNtool by the guy on guru3d
Works great for all over clocking, undervolting and fan control. I mod all my bios with polaris 1.6 but if I need to tweak anything after I use overdriveNtool
|
|
|
|
|
Anyone else getting DEVFEE hang up? Starts to mine on DEVFEE- gets 3-4 ETH shares then INCORRECT SHARES start and it continues until I catch it. Lost 45 minutes as it's contagious and miner kept trying to get DEVFEE and producing incorrect shares one after another. Miner was stable for 10.5 hrs prior. Happened this morning too.
It appears based on logs that GPU 2 drops to 0 hash when devfee starts. But it is different GPU that starts the incorrect share on DEVFEE issue then one after another incorrect share over and over and over on devfee.
|
|
|
|
|
