Show Posts
|
Pages: [1]
|
2
|
Bitcoin / Pools / Re: [440 TH] BitMinter.com [1% PPLNS,Pays TxFees + MergedMining,Stratum,GBT,vardiff]
|
on: February 12, 2014, 05:34:08 AM
|
Can some one help me figure out what's wrong with my hash rate I was running one erupter blade and 3 of the usb erupters (333 mhash) and getting averaging about 10.5 Ghash. I have added one more blade and now getting only 16 to 17 Ghash per shift. Every time I check the blades configuration page they are all ways running a 99% plus and over 10 Ghash each. Any ideas what I should look for on my end ?
Are you getting a lot of rejected work or hardware errors (miscalculations) ? I'm not sure if the blade web interface shows hardware errors? [/quote] According to the bitminter live stats I have a rejection rate of 0.03% for currant round Total MHS: 10968 Received: 0000135770 Accepted: 0000135632 After 15 hours for one blade and Total MHS: 10435 Received: 0000304830 Accepted: 0000298874 for the other 1 day and 10 plus hours
|
|
|
3
|
Bitcoin / Pools / Re: [440 TH] BitMinter.com [1% PPLNS,Pays TxFees + MergedMining,Stratum,GBT,vardiff]
|
on: February 11, 2014, 05:36:17 AM
|
Can some one help me figure out what's wrong with my hash rate I was running one erupter blade and 3 of the usb erupters (333 mhash) and getting averaging about 10.5 Ghash. I have added one more blade and now getting only 16 to 17 Ghash per shift. Every time I check the blades configuration page they are all ways running a 99% plus and over 10 Ghash each. Any ideas what I should look for on my end ?
|
|
|
4
|
Bitcoin / Hardware / Re: [Guide] Dogie's Comprehensive ASICMiner Blade Setup
|
on: January 11, 2014, 09:20:09 AM
|
ok I have tried connecting to slushes pool and the bitminter pool using both stratum proxy and bfgminer I have tried turning my firewall off. Any help would be great Thanks
this is what I get the the cmd window 014-01-11 05:24:50,530 ERROR protocol protocol.dataReceived # Processing of mes sage failed Traceback (most recent call last): File "stratum\protocol.pyo", line 185, in dataReceived File "stratum\protocol.pyo", line 216, in lineReceived 'rotocolException: Cannot decode message 'POST / HTTP/1.1 2014-01-11 05:24:50,535 INFO stats stats.print_stats # 2 peers connected, state changed 1 times 2014-01-11 05:24:50,540 INFO stats stats.print_stats # 3 peers connected, state changed 1 times 2014-01-11 05:24:50,552 ERROR protocol protocol.dataReceived # Processing of mes sage failed Traceback (most recent call last): File "stratum\protocol.pyo", line 185, in dataReceived File "stratum\protocol.pyo", line 216, in lineReceived 'rotocolException: Cannot decode message 'POST / HTTP/1.1 2014-01-11 05:24:50,559 INFO stats stats.print_stats # 2 peers connected, state changed 1 times 2014-01-11 05:24:50,562 INFO stats stats.print_stats # 3 peers connected, state changed 1 times 2014-01-11 05:24:50,572 ERROR protocol protocol.dataReceived # Processing of mes sage failed Traceback (most recent call last): File "stratum\protocol.pyo", line 185, in dataReceived File "stratum\protocol.pyo", line 216, in lineReceived 'rotocolException: Cannot decode message 'POST / HTTP/1.1 over and over and over
|
|
|
5
|
Bitcoin / Hardware / Re: [Guide] Dogie's Comprehensive ASICMiner Blade Setup
|
on: January 09, 2014, 10:25:57 AM
|
Ok I could use some help I have one blade hooked up via backplane with a 1000 watt power supply and I can not get it to mine. I have tried stratum proxy and bfgminer.
IP 192.168.1.201 ( Ip i have it set to ) Mask 255.255.255.0 Gateway 192.168.1.1 ( router ip) WEB Port 8000 Primary DNS 192.168.1.1 Secondary DNS 211.148.192.141 Ports 3333,3333 ( ports for bitminter) Server addresses 174.73.8.178,174.73.8.178 My ip user:pass my username and pass word
I even tried replacing the cable going from the blade to the router . What am I missing. Thanks in advance
try changing your server to the same IP range (192.168.1.xxx) I changed the server to 192.168.1.102 The ip address of my computer on the net work but still no luck I am running windows 7 64 bit
|
|
|
6
|
Bitcoin / Hardware / Re: [Guide] Dogie's Comprehensive ASICMiner Blade Setup
|
on: January 08, 2014, 10:04:03 AM
|
Ok I could use some help I have one blade hooked up via backplane with a 1000 watt power supply and I can not get it to mine. I have tried stratum proxy and bfgminer.
IP 192.168.1.201 ( Ip i have it set to ) Mask 255.255.255.0 Gateway 192.168.1.1 ( router ip) WEB Port 8000 Primary DNS 192.168.1.1 Secondary DNS 211.148.192.141 Ports 3333,3333 ( ports for bitminter) Server addresses 174.73.8.178,174.73.8.178 My ip user:pass my username and pass word
I even tried replacing the cable going from the blade to the router . What am I missing. Thanks in advance
|
|
|
7
|
Bitcoin / Group buys / Re: [OPEN] BM1380 Worldwide Chip Groupbuy
|
on: December 14, 2013, 11:38:29 PM
|
I would be in for at least 50 depending on final cost of miner USB would be great. I would also have to pay in USD
Sorry payment is in BTC as that is what we have to pay Bitmain with. NP understood
|
|
|
|