 Show Posts
|
|
Pages: [1]
|
Can you please connect a fully working hash board to the controller port J5?
If it is working ok, then I would say that the control board is ok.
And that there is one faulty hash board.
Well, I conneted a faultiboard to J6 connector and error apears now in [Chain6]. Hasboard is the problem so. |
|
|
|
Now connected, J7 and J6, works??  .
.
[ 30.603875] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
This is XILINX board. Totalram: 507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : 80641d2e2420881c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000c0
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[39] has core num=1
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Chain[7] ASIC[37] has core num=1
Check chain[7] PIC fw version=0x03
get PIC voltage=125 on chain[6], value=870
get PIC voltage=6 on chain[7], value=940
set_reset_allhashboard = 0x00000000
chain[6] temp offset record: 62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
chain[7] temp offset record: 62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL
--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
search freq for 1 times, completed chain = 2, total chain num = 2
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1373 root 0:00 grep bmminer
bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Fri Nov 17 17:57:49 CST 2017 type: Antminer S9set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 80641d2e2420881c
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[5] speed=6120
get fan[2] speed=4560
get fan[5] speed=6120
get fan[2] speed=4560
get fan[5] speed=6120
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J7] has backup chain_voltage=870
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J8] has backup chain_voltage=870
Check chain[7] PIC fw version=0x03
Chain[J7] orignal chain_voltage_pic=125 value=870
Chain[J8] orignal chain_voltage_pic=6 value=940
Chain[J8] will use backup chain_voltage_pic=870 [125]
Chain[J8] get working chain_voltage_pic=125
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J7] has core num in PIC
Chain[J7] ASIC[39] has core num=1
Chain[J8] has core num in PIC
Chain[J8] ASIC[37] has core num=1
miner total rate=9335GH/s fixed rate=9000GH/s
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=650
Asic[ 0]:650
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650
Chain:6 max freq=650
Chain:6 min freq=650
read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=650
Asic[ 0]:650
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650
Chain:7 max freq=650
Chain:7 min freq=650
Miner fix freq ...
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=650
Asic[ 0]:650
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650
Chain:6 max freq=650
Chain:6 min freq=650
read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=650
Asic[ 0]:650
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650
Chain:7 max freq=650
Chain:7 min freq=650
max freq = 650
set baud=1
Chain[J7] PIC temp offset=62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:23 remote:26 offset:26
Chain[J7] chip[244] get middle temp offset=26 typeID=55
Chain[J8] PIC temp offset=62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:23 remote:26 offset:26
Chain[J8] chip[244] get middle temp offset=26 typeID=55
Chain[J7] set working voltage=870 [125]
Chain[J8] set working voltage=870 [125]
do heat board 8xPatten for 1 times
start send works on chain[6]
start send works on chain[7]
get send work num :57456 on Chain[6]
get send work num :57456 on Chain[7]
wait recv nonce on chain[6]
wait recv nonce on chain[7]
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=912 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
freq[00]=650 freq[01]=650 freq[02]=650 freq[03]=650 freq[04]=650 freq[05]=650 freq[06]=650 freq[07]=650
freq[08]=650 freq[09]=650 freq[10]=650 freq[11]=650 freq[12]=650 freq[13]=650 freq[14]=650 freq[15]=650
freq[16]=650 freq[17]=650 freq[18]=650 freq[19]=650 freq[20]=650 freq[21]=650 freq[22]=650 freq[23]=650
freq[24]=650 freq[25]=650 freq[26]=650 freq[27]=650 freq[28]=650 freq[29]=650 freq[30]=650 freq[31]=650
freq[32]=650 freq[33]=650 freq[34]=650 freq[35]=650 freq[36]=650 freq[37]=650 freq[38]=650 freq[39]=650
freq[40]=650 freq[41]=650 freq[42]=650 freq[43]=650 freq[44]=650 freq[45]=650 freq[46]=650 freq[47]=650
freq[48]=650 freq[49]=650 freq[50]=650 freq[51]=650 freq[52]=650 freq[53]=650 freq[54]=650 freq[55]=650
freq[56]=650 freq[57]=650 freq[58]=650 freq[59]=650 freq[60]=650 freq[61]=650 freq[62]=650
total valid nonce number:57456
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:26639
last_nonce_num:29040
get nonces on chain[7]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=912 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
freq[00]=650 freq[01]=650 freq[02]=650 freq[03]=650 freq[04]=650 freq[05]=650 freq[06]=650 freq[07]=650
freq[08]=650 freq[09]=650 freq[10]=650 freq[11]=650 freq[12]=650 freq[13]=650 freq[14]=650 freq[15]=650
freq[16]=650 freq[17]=650 freq[18]=650 freq[19]=650 freq[20]=650 freq[21]=650 freq[22]=650 freq[23]=650
freq[24]=650 freq[25]=650 freq[26]=650 freq[27]=650 freq[28]=650 freq[29]=650 freq[30]=650 freq[31]=650
freq[32]=650 freq[33]=650 freq[34]=650 freq[35]=650 freq[36]=650 freq[37]=650 freq[38]=650 freq[39]=650
freq[40]=650 freq[41]=650 freq[42]=650 freq[43]=650 freq[44]=650 freq[45]=650 freq[46]=650 freq[47]=650
freq[48]=650 freq[49]=650 freq[50]=650 freq[51]=650 freq[52]=650 freq[53]=650 freq[54]=650 freq[55]=650
freq[56]=650 freq[57]=650 freq[58]=650 freq[59]=650 freq[60]=650 freq[61]=650 freq[62]=650
total valid nonce number:57456
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:26627
last_nonce_num:33868
chain[6]: All chip cores are opened OK!
Test Patten on chain[6]: OK!
chain[7]: All chip cores are opened OK!
Test Patten on chain[7]: OK!
setStartTimePoint total_tv_start_sys=141 total_tv_end_sys=142
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08
get RT hashrate from Chain[6]: (asic index start from 1-63)
Asic[01]=121.618 Asic[02]=113.984 Asic[03]=116.165 Asic[04]=115.444 Asic[05]=117.474 Asic[06]=115.444 Asic[07]=116.534 Asic[08]=116.198
Asic[09]=116.819 Asic[10]=117.591 Asic[11]=115.125 Asic[12]=119.990 Asic[13]=116.014 Asic[14]=513.164 Asic[15]=115.712 Asic[16]=114.588
Asic[17]=118.044 Asic[18]=115.293 Asic[19]=400.203 Asic[20]=118.984 Asic[21]=119.554 Asic[22]=112.558 Asic[23]=118.145 Asic[24]=113.548
Asic[25]=116.752 Asic[26]=119.604 Asic[27]=117.893 Asic[28]=116.886 Asic[29]=131.617 Asic[30]=118.413 Asic[31]=111.383 Asic[32]=118.128
Asic[33]=111.753 Asic[34]=114.487 Asic[35]=116.198 Asic[36]=265.801 Asic[37]=119.621 Asic[38]=120.108 Asic[39]=114.504 Asic[40]=116.081
Asic[41]=115.477 Asic[42]=119.135 Asic[43]=115.964 Asic[44]=114.739 Asic[45]=664.595 Asic[46]=118.044 Asic[47]=116.568 Asic[48]=1559.01
Asic[49]=112.273 Asic[50]=116.048 Asic[51]=115.695 Asic[52]=120.712 Asic[53]=116.886 Asic[54]=117.541 Asic[55]=117.255 Asic[56]=118.279
Asic[57]=128.731 Asic[58]=115.561 Asic[59]=115.225 Asic[60]=115.527 Asic[61]=116.500 Asic[62]=115.125 Asic[63]=121.701
get RT hashrate from Chain[7]: (asic index start from 1-63)
Asic[01]=117.289 Asic[02]=112.692 Asic[03]=113.514 Asic[04]=110.628 Asic[05]=116.182 Asic[06]=111.904 Asic[07]=114.638 Asic[08]=116.819
Asic[09]=116.668 Asic[10]=114.252 Asic[11]=114.588 Asic[12]=115.997 Asic[13]=112.558 Asic[14]=484.727 Asic[15]=114.420 Asic[16]=111.702
Asic[17]=116.870 Asic[18]=114.118 Asic[19]=114.907 Asic[20]=114.001 Asic[21]=117.776 Asic[22]=111.635 Asic[23]=252.547 Asic[24]=110.343
Asic[25]=114.823 Asic[26]=116.266 Asic[27]=114.286 Asic[28]=113.212 Asic[29]=131.533 Asic[30]=114.403 Asic[31]=109.672 Asic[32]=112.357
Asic[33]=111.333 Asic[34]=111.132 Asic[35]=115.578 Asic[36]=114.336 Asic[37]=117.172 Asic[38]=116.282 Asic[39]=112.122 Asic[40]=628.944
Asic[41]=111.316 Asic[42]=119.621 Asic[43]=116.081 Asic[44]=114.621 Asic[45]=114.856 Asic[46]=119.168 Asic[47]=116.098 Asic[48]=1466.46
Asic[49]=108.833 Asic[50]=113.044 Asic[51]=114.370 Asic[52]=116.584 Asic[53]=114.051 Asic[54]=116.198 Asic[55]=115.175 Asic[56]=376.245
Asic[57]=127.741 Asic[58]=113.195 Asic[59]=118.178 Asic[60]=112.407 Asic[61]=214.714 Asic[62]=111.971 Asic[63]=118.749
Check Chain[J7] ASIC RT error: (asic index start from 1-63)
Asic[01]=121.618000
Asic[02]=113.984000
Asic[03]=116.165000
Asic[04]=115.444000
Asic[05]=117.474000
Asic[06]=115.444000
Asic[07]=116.534000
Asic[08]=116.198000
Asic[09]=116.819000
Asic[10]=117.591000
Asic[11]=115.125000
Asic[12]=119.990000
Asic[13]=116.014000
Asic[14]=513.164000
Asic[15]=115.712000
Asic[16]=114.588000
Asic[17]=118.044000
Asic[18]=115.293000
Asic[19]=400.203000
Asic[20]=118.984000
Asic[21]=119.554000
Asic[22]=112.558000
Asic[23]=118.145000
Asic[24]=113.548000
Asic[25]=116.752000
Asic[26]=119.604000
Asic[27]=117.893000
Asic[28]=116.886000
Asic[29]=131.617000
Asic[30]=118.413000
Asic[31]=111.383000
Asic[32]=118.128000
Asic[33]=111.753000
Asic[34]=114.487000
Asic[35]=116.198000
Asic[36]=265.801000
Asic[37]=119.621000
Asic[38]=120.108000
Asic[39]=114.504000
Asic[40]=116.081000
Asic[41]=115.477000
Asic[42]=119.135000
Asic[43]=115.964000
Asic[44]=114.739000
Asic[45]=664.595000
Asic[46]=118.044000
Asic[47]=116.568000
Asic[48]=1559.010000
Asic[49]=112.273000
Asic[50]=116.048000
Asic[51]=115.695000
Asic[52]=120.712000
Asic[53]=116.886000
Asic[54]=117.541000
Asic[55]=117.255000
Asic[56]=118.279000
Asic[57]=128.731000
Asic[58]=115.561000
Asic[59]=115.225000
Asic[60]=115.527000
Asic[61]=116.500000
Asic[62]=115.125000
Asic[63]=121.701000
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Asic[01]=117.289000
Asic[02]=112.692000
Asic[03]=113.514000
Asic[04]=110.628000
Asic[05]=116.182000
Asic[06]=111.904000
Asic[07]=114.638000
Asic[08]=116.819000
Asic[09]=116.668000
Asic[10]=114.252000
Asic[11]=114.588000
Asic[12]=115.997000
Asic[13]=112.558000
Asic[14]=484.727000
Asic[15]=114.420000
Asic[16]=111.702000
Asic[17]=116.870000
Asic[18]=114.118000
Asic[19]=114.907000
Asic[20]=114.001000
Asic[21]=117.776000
Asic[22]=111.635000
Asic[23]=252.547000
Asic[24]=110.343000
Asic[25]=114.823000
Asic[26]=116.266000
Asic[27]=114.286000
Asic[28]=113.212000
Asic[29]=131.533000
Asic[30]=114.403000
Asic[31]=109.672000
Asic[32]=112.357000
Asic[33]=111.333000
Asic[34]=111.132000
Asic[35]=115.578000
Asic[36]=114.336000
Asic[37]=117.172000
Asic[38]=116.282000
Asic[39]=112.122000
Asic[40]=628.944000
Asic[41]=111.316000
Asic[42]=119.621000
Asic[43]=116.081000
Asic[44]=114.621000
Asic[45]=114.856000
Asic[46]=119.168000
Asic[47]=116.098000
Asic[48]=1466.460000
Asic[49]=108.833000
Asic[50]=113.044000
Asic[51]=114.370000
Asic[52]=116.584000
Asic[53]=114.051000
Asic[54]=116.198000
Asic[55]=115.175000
Asic[56]=376.245000
Asic[57]=127.741000
Asic[58]=113.195000
Asic[59]=118.178000
Asic[60]=112.407000
Asic[61]=214.714000
Asic[62]=111.971000
Asic[63]=118.749000
Done check_asic_reg
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=55 middle offset=26
Chain[6] Chip[62] local Temp=49
Chain[6] Chip[62] middle Temp=58
Special fix Chain[6] Chip[62] middle Temp = 64
Done read temp on Chain[6]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=55 middle offset=26
Chain[7] Chip[62] local Temp=50
Chain[7] Chip[62] middle Temp=59
Special fix Chain[7] Chip[62] middle Temp = 65
Done read temp on Chain[7]
read_temp_func Done!
CRC error counter=0
I don't stand why now work, and some hours before no. |
|
|
|
Hi HagssFIN, I due, equal results: [ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 16800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 126976
[ 0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125984
[ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06d1374 (6949 kB)
[ 0.000000] .init : 0xc06d2000 - 0xc0705380 ( 205 kB)
[ 0.000000] .data : 0xc0706000 - 0xc074cf78 ( 284 kB)
[ 0.000000] .bss : 0xc074cf84 - 0xc078d9fc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to df802000
[ 0.000000] zynq_clock_init: clkc starts at df802100
[ 0.000000] Zynq clock init
[ 0.000014] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000309] ps7-ttc #0 at df804000, irq=43
[ 0.000618] Console: colour dummy device 80x30
[ 0.000650] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[ 0.040211] pid_max: default: 32768 minimum: 301
[ 0.040432] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040452] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.042584] CPU: Testing write buffer coherency: ok
[ 0.042915] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.042973] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[ 0.043199] L310 cache controller enabled
[ 0.043218] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.121036] CPU1: Booted secondary processor
[ 0.210230] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.210362] Brought up 2 CPUs
[ 0.210380] SMP: Total of 2 processors activated.
[ 0.210388] CPU: All CPU(s) started in SVC mode.
[ 0.211051] devtmpfs: initialized
[ 0.213465] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.214684] regulator-dummy: no parameters
[ 0.222345] NET: Registered protocol family 16
[ 0.224576] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.226874] cpuidle: using governor ladder
[ 0.226888] cpuidle: using governor menu
[ 0.234324] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.235850] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.235864] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.235977] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[ 0.257692] bio: create slab <bio-0> at 0
[ 0.259117] vgaarb: loaded
[ 0.259815] SCSI subsystem initialized
[ 0.260913] usbcore: registered new interface driver usbfs
[ 0.261112] usbcore: registered new interface driver hub
[ 0.261348] usbcore: registered new device driver usb
[ 0.261882] media: Linux media interface: v0.10
[ 0.262046] Linux video capture interface: v2.00
[ 0.262287] pps_core: LinuxPPS API ver. 1 registered
[ 0.262299] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.262430] PTP clock support registered
[ 0.262785] EDAC MC: Ver: 3.0.0
[ 0.263846] Advanced Linux Sound Architecture Driver Initialized.
[ 0.266705] DMA-API: preallocated 4096 debug entries
[ 0.266719] DMA-API: debugging enabled by kernel config
[ 0.266792] Switched to clocksource arm_global_timer
[ 0.287904] NET: Registered protocol family 2
[ 0.288559] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.288617] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.288701] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.288747] TCP: reno registered
[ 0.288764] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.288795] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.289027] NET: Registered protocol family 1
[ 0.289381] RPC: Registered named UNIX socket transport module.
[ 0.289393] RPC: Registered udp transport module.
[ 0.289401] RPC: Registered tcp transport module.
[ 0.289410] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.289422] PCI: CLS 0 bytes, default 64
[ 0.289853] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.291862] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.293946] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.294140] msgmni has been set to 967
[ 0.294925] io scheduler noop registered
[ 0.294938] io scheduler deadline registered
[ 0.294991] io scheduler cfq registered (default)
[ 0.307189] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.307210] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.432988] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 1.001244] console [ttyPS0] enabled
[ 1.005510] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[ 1.013154] [drm] Initialized drm 1.1.0 20060810
[ 1.030227] brd: module loaded
[ 1.039612] loop: module loaded
[ 1.049221] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.054972] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.063072] libphy: XEMACPS mii bus: probed
[ 1.067647] ------------- phy_id = 0x3625e62
[ 1.072385] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.081026] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.087679] ehci-pci: EHCI PCI platform driver
[ 1.094894] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.101709] usbcore: registered new interface driver usb-storage
[ 1.108578] mousedev: PS/2 mouse device common for all mice
[ 1.114667] i2c /dev entries driver
[ 1.121624] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.127200] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.133081] Xilinx Zynq CpuIdle Driver started
[ 1.137959] sdhci: Secure Digital Host Controller Interface driver
[ 1.144054] sdhci: Copyright(c) Pierre Ossman
[ 1.148464] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.154191] mmc0: no vqmmc regulator found
[ 1.158232] mmc0: no vmmc regulator found
[ 1.196831] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.205526] usbcore: registered new interface driver usbhid
[ 1.211046] usbhid: USB HID core driver
[ 1.215762] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.222052] nand: Micron MT29F2G08ABAEAWP
[ 1.226023] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.231972] Bad block table found at page 131008, version 0x01
[ 1.238210] Bad block table found at page 130944, version 0x01
[ 1.244258] 3 ofpart partitions found on MTD device pl353-nand
[ 1.250030] Creating 3 MTD partitions on "pl353-nand":
[ 1.255131] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.263189] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.270504] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.279477] TCP: cubic registered
[ 1.282713] NET: Registered protocol family 17
[ 1.287423] Registering SWP/SWPB emulation handler
[ 1.293314] regulator-dummy: disabling
[ 1.297651] UBI: attaching mtd1 to ubi0
[ 1.823951] UBI: scanning is finished
[ 1.835605] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.842685] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.849448] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.856112] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.862989] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 1.868970] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.876078] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1134783803
[ 1.885120] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[ 1.894336] UBI: background thread "ubi_bgt0d" started, PID 1080
[ 1.894342] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.898284] ALSA device list:
[ 1.898288] No soundcards found.
[ 1.914694] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[ 1.943698] UBIFS: recovery needed
[ 2.042505] UBIFS: recovery completed
[ 2.046164] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 2.052115] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 2.061221] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 2.071110] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 2.076139] UBIFS: media format: w4/r0 (latest is w4/r0), UUID B079DD56-06BB-4E31-8F5E-A6604F480DB2, small LPT model
[ 2.087450] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 2.094858] devtmpfs: mounted
[ 2.097983] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[ 2.935918] random: dd urandom read with 0 bits of entropy available
[ 3.326829]
[ 3.326829] bcm54xx_config_init
[ 3.936838]
[ 3.936838] bcm54xx_config_init
[ 7.937672] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 7.943773] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[ 25.222130] In axi fpga driver!
[ 25.225204] request_mem_region OK!
[ 25.228626] AXI fpga dev virtual address is 0xdf9fc000
[ 25.233701] *base_vir_addr = 0x8c510
[ 25.249251] In fpga mem driver!
[ 25.252321] request_mem_region OK!
[ 25.255882] fpga mem virtual address is 0xe2000000
[ 26.056857]
[ 26.056857] bcm54xx_config_init
[ 26.686843]
[ 26.686843] bcm54xx_config_init
[ 30.687670] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 30.693773] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
This is XILINX board. Totalram: 507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : 80641d2e2420881c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
Find /tmp/searcherror: U6:1 The last log is below:
This is XILINX board. Totalram: 507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : 80641d2e2420881c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x00
chain[5] PIC need restore ...
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
After restore: chain[5] PIC fw version=0x00
J6 (Chain 6) only connected seem work fine: [ 25.215585] In fpga mem driver!
[ 25.218722] request_mem_region OK!
[ 25.222220] fpga mem virtual address is 0xe2000000
[ 26.017029]
[ 26.017029] bcm54xx_config_init
[ 26.647044]
[ 26.647044] bcm54xx_config_init
[ 30.647879] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 30.653984] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
This is XILINX board. Totalram: 507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : 80641d2e2420881c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x00000040
Find hashboard on Chain[6]
set_reset_allhashboard = 0x0000ffff
Check chain[6] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[39] has core num=1
Check chain[6] PIC fw version=0x03
get PIC voltage=6 on chain[6], value=940
set_reset_allhashboard = 0x00000000
chain[6] temp offset record: 62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL
--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
search freq for 1 times, completed chain = 1, total chain num = 1
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1364 root 0:00 grep bmminer
bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Fri Nov 17 17:57:49 CST 2017 type: Antminer S9set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 80641d2e2420881c
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[5] speed=6120
get fan[2] speed=4560
get fan[5] speed=6120
get fan[2] speed=4560
get fan[5] speed=6120
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J7] has backup chain_voltage=870
Check chain[6] PIC fw version=0x03
Chain[J7] orignal chain_voltage_pic=6 value=940
Chain[J7] will use backup chain_voltage_pic=870 [125]
Chain[J7] get working chain_voltage_pic=125
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J7] has 63 asic
Chain[J7] has core num in PIC
Chain[J7] ASIC[39] has core num=1
miner total rate=4667GH/s fixed rate=4500GH/s
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=650
Asic[ 0]:650
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650
Chain:6 max freq=650
Chain:6 min freq=650
Miner fix freq ...
read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=650
Asic[ 0]:650
Asic[ 1]:650 Asic[ 2]:650 Asic[ 3]:650 Asic[ 4]:650 Asic[ 5]:650 Asic[ 6]:650 Asic[ 7]:650 Asic[ 8]:650
Asic[ 9]:650 Asic[10]:650 Asic[11]:650 Asic[12]:650 Asic[13]:650 Asic[14]:650 Asic[15]:650 Asic[16]:650
Asic[17]:650 Asic[18]:650 Asic[19]:650 Asic[20]:650 Asic[21]:650 Asic[22]:650 Asic[23]:650 Asic[24]:650
Asic[25]:650 Asic[26]:650 Asic[27]:650 Asic[28]:650 Asic[29]:650 Asic[30]:650 Asic[31]:650 Asic[32]:650
Asic[33]:650 Asic[34]:650 Asic[35]:650 Asic[36]:650 Asic[37]:650 Asic[38]:650 Asic[39]:650 Asic[40]:650
Asic[41]:650 Asic[42]:650 Asic[43]:650 Asic[44]:650 Asic[45]:650 Asic[46]:650 Asic[47]:650 Asic[48]:650
Asic[49]:650 Asic[50]:650 Asic[51]:650 Asic[52]:650 Asic[53]:650 Asic[54]:650 Asic[55]:650 Asic[56]:650
Asic[57]:650 Asic[58]:650 Asic[59]:650 Asic[60]:650 Asic[61]:650 Asic[62]:650
Chain:6 max freq=650
Chain:6 min freq=650
max freq = 650
set baud=1
Chain[J7] PIC temp offset=62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:22 remote:25 offset:26
Chain[J7] chip[244] get middle temp offset=26 typeID=55
Chain[J7] set working voltage=870 [125]
do heat board 8xPatten for 1 times
start send works on chain[6]
do read_temp_func once...
do check_asic_reg 0x08
Done check_asic_reg
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=55 middle offset=26
Chain[6] Chip[62] local Temp=29
Chain[6] Chip[62] middle Temp=40
Special fix Chain[6] Chip[62] middle Temp = 44
Done read temp on Chain[6]
Set fixed fan speed=70
FAN PWM: 70
read_temp_func Done!
CRC error counter=0
|
|
|
|
Hi, equal problem in my S9 new hardware.(MARCH 2018 bach) Today are aribed and after 30 minutes working weel at 13.5THs, i rebooted and don't work anymore. 3 harsh boards are red led off, some times, reboting the middel board leds are stand red. I have a 2 BITMAIN 1600W PSU equalt results with 2 power supply. Sistem don't run bmminer binary and no has rate. Fans runs at full speed after some seconds of boot and don't decrease speed. Kernel log: [ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 16800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 126976
[ 0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125984
[ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06d1374 (6949 kB)
[ 0.000000] .init : 0xc06d2000 - 0xc0705380 ( 205 kB)
[ 0.000000] .data : 0xc0706000 - 0xc074cf78 ( 284 kB)
[ 0.000000] .bss : 0xc074cf84 - 0xc078d9fc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to df802000
[ 0.000000] zynq_clock_init: clkc starts at df802100
[ 0.000000] Zynq clock init
[ 0.000016] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000313] ps7-ttc #0 at df804000, irq=43
[ 0.000617] Console: colour dummy device 80x30
[ 0.000649] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[ 0.040212] pid_max: default: 32768 minimum: 301
[ 0.040432] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040451] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.042591] CPU: Testing write buffer coherency: ok
[ 0.042930] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.042990] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[ 0.043215] L310 cache controller enabled
[ 0.043235] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.121038] CPU1: Booted secondary processor
[ 0.210230] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.210361] Brought up 2 CPUs
[ 0.210380] SMP: Total of 2 processors activated.
[ 0.210388] CPU: All CPU(s) started in SVC mode.
[ 0.211049] devtmpfs: initialized
[ 0.213459] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.214669] regulator-dummy: no parameters
[ 0.222329] NET: Registered protocol family 16
[ 0.224564] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.226858] cpuidle: using governor ladder
[ 0.226872] cpuidle: using governor menu
[ 0.234325] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.235844] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.235858] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.235972] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[ 0.257674] bio: create slab <bio-0> at 0
[ 0.259099] vgaarb: loaded
[ 0.259800] SCSI subsystem initialized
[ 0.260816] usbcore: registered new interface driver usbfs
[ 0.260995] usbcore: registered new interface driver hub
[ 0.261255] usbcore: registered new device driver usb
[ 0.261796] media: Linux media interface: v0.10
[ 0.261954] Linux video capture interface: v2.00
[ 0.262202] pps_core: LinuxPPS API ver. 1 registered
[ 0.262214] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.262337] PTP clock support registered
[ 0.262692] EDAC MC: Ver: 3.0.0
[ 0.263742] Advanced Linux Sound Architecture Driver Initialized.
[ 0.266580] DMA-API: preallocated 4096 debug entries
[ 0.266595] DMA-API: debugging enabled by kernel config
[ 0.266671] Switched to clocksource arm_global_timer
[ 0.287330] NET: Registered protocol family 2
[ 0.287981] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.288038] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.288123] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.288167] TCP: reno registered
[ 0.288185] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.288215] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.288462] NET: Registered protocol family 1
[ 0.288765] RPC: Registered named UNIX socket transport module.
[ 0.288777] RPC: Registered udp transport module.
[ 0.288786] RPC: Registered tcp transport module.
[ 0.288794] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.288807] PCI: CLS 0 bytes, default 64
[ 0.289241] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.291251] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.293391] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.293575] msgmni has been set to 967
[ 0.294359] io scheduler noop registered
[ 0.294373] io scheduler deadline registered
[ 0.294420] io scheduler cfq registered (default)
[ 0.307123] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.307143] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.429705] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 0.997873] console [ttyPS0] enabled
[ 1.002148] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[ 1.009797] [drm] Initialized drm 1.1.0 20060810
[ 1.026910] brd: module loaded
[ 1.036218] loop: module loaded
[ 1.045711] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.051696] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.059599] libphy: XEMACPS mii bus: probed
[ 1.063973] ------------- phy_id = 0x3625e62
[ 1.068933] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.077605] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.084231] ehci-pci: EHCI PCI platform driver
[ 1.091511] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.098347] usbcore: registered new interface driver usb-storage
[ 1.105180] mousedev: PS/2 mouse device common for all mice
[ 1.111317] i2c /dev entries driver
[ 1.118272] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.123754] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.129666] Xilinx Zynq CpuIdle Driver started
[ 1.134509] sdhci: Secure Digital Host Controller Interface driver
[ 1.140688] sdhci: Copyright(c) Pierre Ossman
[ 1.144956] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.151780] mmc0: no vqmmc regulator found
[ 1.155792] mmc0: no vmmc regulator found
[ 1.196690] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.205392] usbcore: registered new interface driver usbhid
[ 1.210908] usbhid: USB HID core driver
[ 1.215607] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.221910] nand: Micron MT29F2G08ABAEAWP
[ 1.225874] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.231821] Bad block table found at page 131008, version 0x01
[ 1.238042] Bad block table found at page 130944, version 0x01
[ 1.244091] 3 ofpart partitions found on MTD device pl353-nand
[ 1.249874] Creating 3 MTD partitions on "pl353-nand":
[ 1.254965] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.263029] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.270367] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.279321] TCP: cubic registered
[ 1.282555] NET: Registered protocol family 17
[ 1.287268] Registering SWP/SWPB emulation handler
[ 1.293148] regulator-dummy: disabling
[ 1.297496] UBI: attaching mtd1 to ubi0
[ 1.823251] UBI: scanning is finished
[ 1.834897] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.841980] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.848743] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.855407] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.862284] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 1.868265] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.875372] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1134783803
[ 1.884415] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[ 1.893631] UBI: background thread "ubi_bgt0d" started, PID 1080
[ 1.893636] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.897593] ALSA device list:
[ 1.897596] No soundcards found.
[ 1.914009] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[ 1.971287] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.977250] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.986334] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 1.996241] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 2.001278] UBIFS: media format: w4/r0 (latest is w4/r0), UUID B079DD56-06BB-4E31-8F5E-A6604F480DB2, small LPT model
[ 2.013019] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 2.020482] devtmpfs: mounted
[ 2.023590] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[ 2.862900] random: dd urandom read with 0 bits of entropy available
[ 3.256695]
[ 3.256695] bcm54xx_config_init
[ 3.866740]
[ 3.866740] bcm54xx_config_init
[ 7.867535] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 7.873641] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[ 25.417709] In axi fpga driver!
[ 25.420774] request_mem_region OK!
[ 25.424165] AXI fpga dev virtual address is 0xdf9fc000
[ 25.429300] *base_vir_addr = 0x8c510
[ 25.444611] In fpga mem driver!
[ 25.447748] request_mem_region OK!
[ 25.451255] fpga mem virtual address is 0xe2000000
[ 26.256691]
[ 26.256691] bcm54xx_config_init
[ 26.886690]
[ 26.886690] bcm54xx_config_init
[ 30.887535] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 30.893641] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
This is XILINX board. Totalram: 507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : 80641d2e2420881c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
Find /tmp/searcherror: U6:1 The last log is below:
This is XILINX board. Totalram: 507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : 80641d2e2420881c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x00
chain[5] PIC need restore ...
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
After restore: chain[5] PIC fw version=0x00
|
|
|
|
|
