Odd question...

First my parts:

2x r606
4x newpac w/ cooling fan
1x 7port gekkoscienc hub
1x  POWER SUPPLY / BREAK OUT BOARD / 6 24″ PCIE CABLES (419mining setup)

1x pi3b+ running raspian

Here is the question before the recen change to cgminer my newpacs were getting avg 110gh each

Bought r606 ran update on cgminer now they get 75gh avg... adding the r606 i got maybe comined of 1.2th

Is it possible to run multiple cgminers

1 for the newpacs and 1 for each of the r606
Or is it a waste of thought...

I am not even getting 2th with this setup

Something is not right

Thanks for any feedback

So I was dog tired last night but I ended up getting all 4 Newpac's and the R606 up and running.

I know that i set the Newpac to freq 525 as i had before but now they dont seem to be running the same since i added the r606

I will get stats later (at work now)

i was hitting about 450-500gh on the newpacs before the addition of the r606 so that is my reference point i am going off of.

not remembering my settings i am currently getting 1.392 th/s as of 5 mins ago i do not have the 24 avg yet of course.

what does this mean?

asic plataeu: (1/3)392.71MHz

I need help.

I dont know what I am doing.

Here us what I have:

1 X R606
4 X NewPac
1 X Raspberry Pi
1 X 7 port hub (Gekko Science)
1 X DPS-1200FB-1A Power Supply; 1 × Bundle PCIe Power Cable – 24″ (6 pack) – 8Pin

I had it working at 1 point before i added the r606.

I ended up wiping and now have fresh install of raspian.

Followed steps on page 1

How do you create a start file that fires everything up.

The file that has stratum, password, freq and all that stuff.

So lost and looking for help.

Thanks to any one

Also huge props to 419mining for super fast shipping and service.

Thank again in advance

-Josh

Okay, for the life of me i cant get this to work on my pi3, gekko science 7port, 4 newpac stick setup.

I need literal step by step. Page 1 does not help.

I followed it via cut copy and paste both by putty and direct on the pi.

Do not know how to creat a file to put my pool, username, pass, anything.

Need precise clear instructions

Can make 3 sticks work on win10 setup, but when inserting 4th stick fails all the way around.

Please help

Thank you

Filax,

How much would you charge to make a box like yours?  Can you tell me what program you are using to do the print job and the steps i need to follow?  I have access to a 3d printer at work but have never used it?

Thank you in advance.

-Josh Gage

@VH

so its a brand new pi3 b+ and i tried following the steps on the 1st page of this thread.

I have the pi all set up - installed cgminer - i can get it to run but it will not detect the gekko's (newpac) nor do i know how to edit the file to manually set my freq.

To be honest my command line skills are below par and i am learning as i go.

I did install full win10 pro on the pi but when i run zadig it gets angry cause 32bit to 64bit conflict... plus it was slow as a mutha with only have 1gb ram

Just exploring all options and learning as i go (as i have no idea what i am doing

-Gage

I need help setting up my pi w/ rasbian

I dont understand how to make a .bat file like you would in windows.

Filax,

How were you able to get 2 fans to work?  I have not yet built it, just wanted to know before i screw something up.

Thank you.