Can anyone help me? After running for couple hours I keep getting the same msg and it stops mining. I have it set at 636
—Stratum from pool 0 detected new block—
Any idea guys
Update I set it back to 600mhz and it ran for 24hours and then same thing. .
Do you think I should put a fan on might be overheating?

Hey guys,
Finally got my hands on 2 R606's and i am having issues with one. First one plugged in downloaded driver works perfect.(Trying to run them together same computer) Second one i plug in turns on fans liughts are on but it will not show up in the miner, the program runs shows deficulty etc but the miner is not showing up. only code i get it says failed to intiliaze and open device failirue err -12.
Today i finally got the second one  to run by it self but i want to run them together on one computer and am getting the codes above.
any help is welcome

Thank you for replay 419mining, love your online store and ebay . As soon as i plug the 8th newpac this is what keeps repeating. As soon as i unplug the 8th newpac it goes back to running normally.

Got a question i am not sure if its been asked. I have a i5 laptop that runs all of my gekkoscience usb miners. But i ran into a problem
What i have-
1.
7 Gekko science NewPacs
Gekko science Board with a Fan
2. Another
7 Gekko science NewPacs
Gekko science Board with a Fan
3. 5 2pacs with a offbrand usb hub
4. 5 compacts with its board

So i am having trouble with running the second board of 7 newpacs. No matter what combination i try it just wont work. I tried only new pacs together it wont work. I tried one board with an 8th new pac it wont work. I can runn 7 newpacs all 2pacs and compacts together with no problems but as soon as i add another newpac it wont work. How can i run more then 7 newpacs?

Thank you.

I been reading through the thread but can’t find it. Why do I get FutureBit error permission denied. Any fix to this Moonlander 2

I read the posts before, i know you say hw dont matter as long as the hash rate is fine. but within 10 minutes i have almost 50 hw. any advice what to do. I am running them at 200 mhz with a fan, did not adjust anything else.

i been doing that last couple of days, they were dropping out withing 10 15 minutes after the last adjustment.
10/19 now droppping even sooner all 4 go out within hours
Try hot plug sequence won’t work
Restarting CGMiner makes them go zombie
Reinstalled everything for the 3rd time don’t help
Adjusting voltage don’t help
Tried 3 different computers
@CADuke I am running 4 of them on a 16 hub

i been at it for 3 weeks, 3 days out of 3 weeks they ran perfect. Now they are dying with in hours no chips found. i had all 5 of them go down with in 8 hours and just now 3 within an hour. i started unplugging them and re plugging on get the warlock error. back to square one lol

Thank you sidehack for the info.
thank you

Since this morning I am down to 74.2 gh/s and down to getting .005 dgb I per stick. I pulled one stick out and plugged it back in and watched it’s hash rate went anywhere from 12ghs to 30ghs in matter of seconds. I will have to pull them all off and adjust mhz on the stick individually to get them more stable. Any idea how to make the CGMiner full screen?

Thank you

In cgminer that i am using for the 2pac what do these mean

Bm1384:02 175.00 MHZ T:175 P-174 (112:223) : 100% WU:93%

the T, P, () and then the percentages after parenthesis

thank you

i have not, he was running them at the same settings i am trying to 150-170.

yes, i have 2 artic fans cooling them. I did buy them used and were working properly for previous owner. Currently they been running strong for last 3 hours with out hiccup @ 74.5gh/s(was at approx 76gh/s). but i am still receiving less DGB  .010 -  .011 before i was getting .013

good morning,
I purchased my 4x2pac BM1384 usb miners. I had thought time getting them to work properly. After 3 days i finally got them running perfect fallowing everyone's posts on here (thank you). I am running them at 170 mhz @ approx. 76 gh/s. Yesterday i played with mhz and it was running unstable. Now i placed them back on 170 and i am getting avg 74gh/s. Any idea what might of happend. Hw-0 wu 1040( 100% for most part Wu:95-100 for each). Thank you
To add to the post i was getting .013 of dgb and now iam only getting .009-.01
Thank you


Now its saying about hour after 0 chips found on 1 or 2 of them, now i am back to square one lol

good morning,
I purchased my 4x2pac BM1384 usb miners. I had thought time getting them to work properly. After 3 days i finally got them running perfect fallowing everyone's posts on here (thank you). I am running them at 170 mhz @ approx. 76 gh/s. Yesterday i played with mhz and it was running unstable. Now i placed them back on 170 and i am getting avg 74gh/s. Any idea what might of happend. Hw-0 wu 1040( 100% for most part Wu:95-100 for each). Thank you
To add to the post i was getting .013 of dgb and now iam only getting .009-.01
Thank you