Show Posts
|
Pages: [1]
|
Hello thank you My problem was solved Apparently there was no problem with the bitmain firmware With the programming two of the hashboards were solved again................ And the device's hash rate came back above 19 While it didn't reach 18 before, the average hash rate was about 17.5 Everything is clear in the picture http://uupload.ir/files/xpny_s11.jpg
|
|
|
Hello thank you No I ask a question And I want to talk about it There is no problem with the software And the control board of Miner V9 is easily downgraded to the S11 or S17 The only problem is: In the Miner V9 board, we do not have the power output to control apw8 and apw9 powers If we can find it The problem is solved
s11 s15 emc control boards 7007 boards http://uupload.ir/files/od72_controller-s11.png
|
|
|
i change t1 setting But Hash Rate can't increase my power is 1800watt i use 2500 watt 12volt server power i set factory factory+ factory++ performance -- performance - performance performance + performance ++
the hashrate cannot increase from 15.8th/s in 24hour
What could be the reason?
|
|
|
hello I have an idea Read the file of nand ic 29f2g08abea from another s11 miner 7007 control boards with tnm5000 universal programmer And write it to my miner ic flash.... I think that's right What do you think??
|
|
|
[...]
Hello As you say, the S9+ is a good word If I only knew that by flashing or upgrading, the hash rate would go down I never did it Now I don't know what to do [...]
Thanks you are right After the update, I realized the consequences of my work I had to read the information with the update file I will test your method and tell you the result The miner S11 fan speed is 4300 to 3000 when mining .
|
|
|
If you check the text above, the frequency of two hashboards is set to the default value of 600. And Miner kernel logs says: Two of the hashboards are badcore. And that's not good at all. Because it reduces the hash rate of two hash boards. Why can't read the frequency data from the hashboard : main.c:8805: Chain[0] read_freq_badcores : 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff main.c:8817: chain[0]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] main.c:8836: chain[0]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] main.c:9068: chain[0] has no freq in PIC! Will use default freq=0 and jump over... main.c:8805: Chain[1] read_freq_badcores : 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff main.c:8817: chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] main.c:8836: chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] main.c:9068: chain[1] has no freq in PIC! Will use default freq=0 and jump over... main.c:8805: Chain[2] read_freq_badcores : 0x7d 0xd9 0x56 0x4e 0x52 0x4e 0x56 0x52 0x52 0x56 0x4e 0x52 0x56 0x4e 0x56 0x4e 0x52 0x56 0x4e 0x52 0x52 0x4e 0x56 0x4e 0x56 0x52 0x4e 0x56 0x52 0x56 0x4e 0x52 0x4e 0x52 0x56 0x52 0x56 0x4e 0x4e 0x56 0x52 0x4e 0x52 0x56 0x52 0x4e 0x56 0x4e 0x52 0x56 0x52 0x4e 0x56 0x52 0x56 0x4e 0x56 0x52 0x4e 0x4e 0x56 0x52 0x4e 0x56 0x52 0x4e 0x52 0x56 0x56 0x4e 0x52 0x56 0x4e 0x52 0x52 0x56 0x4e 0x4e 0x56 0x52 0x56 0x4e 0x52 0x52 0x56 0x4e 0x6a 0x19 0x00 0x00 0xc8 0xef 0xbe 0xef 0xbe 0xff 0xee 0xbb 0xff 0xee 0xfb 0xfb 0xee 0xef 0xee 0xef 0xfb 0xeb 0xbf 0xfb 0xfe 0xfa 0xb7 0x11 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff main.c:8817: chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] main.c:8836: chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] main.c:8923: has freq in PIC, will disable freq setting. main.c:8997: chain[2] has freq in PIC and will jump over... main.c:8999: Chain[2] has core num in PIC main.c:9103: get PIC voltage=97 on chain[0], value=750 main.c:9103: get PIC voltage=97 on chain[1], value=750 main.c:9103: get PIC voltage=0 on chain[2], value=930
|
|
|
Hello. I have an antminer S11 19.5 th miner.Previously, the device's hashrates was good. And the average 24-hour miner hashrates was no less than 19 But now, since I updated to the latest bitcoin firmware, the hash rate has not risen above 17.7. What is the solution? Unfortunately, it doesn't work with sd card downgrade. Because the software version of downgrade is a signnature version. http://uupload.ir/files/2k43_p6.jpgmy miner sofware version http://uupload.ir/files/t8nz_p5.jpgmy miner status s11 kernel logs Booting Linux on physical CPU 0x0 Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018 CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine model: Xilinx Zynq cma: Reserved 16 MiB at 0x0e000000 Memory policy: Data cache writealloc On node 0 totalpages: 61440 free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000 Normal zone: 480 pages used for memmap Normal zone: 0 pages reserved Normal zone: 61440 pages, LIFO batch:15 percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152 pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096 pcpu-alloc: [0] 0 [0] 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60960 Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 199144K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 30232K reserved, 16384K cma-reserved, 0K highmem) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xcf800000 - 0xff800000 ( 768 MB) lowmem : 0xc0000000 - 0xcf000000 ( 240 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc090c424 (9234 kB) .init : 0xc0a00000 - 0xc0b00000 (1024 kB) .data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB) .bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB) Preemptible hierarchical RCU implementation. Build-time adjustment of leaf fanout to 32. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2 NR_IRQS:16 nr_irqs:16 16 efuse mapped to cf800000 ps7-slcr mapped to cf802000 L2C: platform modifies aux control register: 0x72360000 -> 0x72760000 L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000 L2C-310 erratum 769419 enabled L2C-310 enabling early BRESP for Cortex-A9 L2C-310 full line of zeros enabled for Cortex-A9 L2C-310 ID prefetch enabled, offset 1 lines L2C-310 dynamic clock gating enabled, standby mode enabled L2C-310 cache controller enabled, 8 ways, 512 kB L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001 zynq_clock_init: clkc starts at cf802100 Zynq clock init sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns Switching to timer-based delay loop, resolution 3ns clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns ps7-ttc #0 at cf80a000, irq=18 Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x100000 - 0x100058 CPU1: failed to boot: -1 Brought up 1 CPUs SMP: Total of 1 processors activated (666.66 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations cpuidle: using governor menu hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000 vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb media: Linux media interface: v0.10 Linux video capture interface: v2.00 pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> PTP clock support registered EDAC MC: Ver: 3.0.0 Advanced Linux Sound Architecture Driver Initialized. clocksource: Switched to clocksource arm_global_timer NET: Registered protocol family 2 TCP established hash table entries: 2048 (order: 1, 8192 bytes) TCP bind hash table entries: 2048 (order: 2, 16384 bytes) TCP: Hash tables configured (established 2048 bind 2048) UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. PCI: CLS 0 bytes, default 64 Trying to unpack rootfs image as initramfs... rootfs image is not initramfs (no cpio magic); looks like an initrd Freeing initrd memory: 17192K (cca37000 - cdb01000) hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available futex hash table entries: 512 (order: 3, 32768 bytes) workingset: timestamp_bits=28 max_order=16 bucket_order=0 jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330 dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16 e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps console [ttyPS0] enabled xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000 [drm] Initialized drm 1.1.0 20060810 brd: module loaded loop: module loaded CAN device driver interface gpiod_set_value: invalid GPIO libphy: MACB_mii_bus: probed macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00) Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1) e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k e1000e: Copyright(c) 1999 - 2015 Intel Corporation. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver usbcore: registered new interface driver usb-storage mousedev: PS/2 mouse device common for all mice i2c /dev entries driver Xilinx Zynq CpuIdle Driver started sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA ledtrig-cpu: registered to indicate activity on CPUs usbcore: registered new interface driver usbhid usbhid: USB HID core driver nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda nand: Micron MT29F2G08ABAEAWP nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 6 ofpart partitions found on MTD device pl35x-nand Creating 6 MTD partitions on "pl35x-nand": 0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel" 0x000002800000-0x000004800000 : "ramfs" 0x000004800000-0x000005000000 : "configs" 0x000005000000-0x000006000000 : "reserve" 0x000006000000-0x000008000000 : "ramfs-bak" 0x000008000000-0x000010000000 : "reserve1" NET: Registered protocol family 10 sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 can: controller area network core (rev 20120528 abi 9) NET: Registered protocol family 29 can: raw protocol (rev 20120528) can: broadcast manager protocol (rev 20120528 t) can: netlink gateway (rev 20130117) max_hops=1 zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05' zynq_pm_late_init: Unable to map DDRC IO memory. Registering SWP/SWPB emulation handler hctosys: unable to open rtc device (rtc0) ALSA device list: No soundcards found. RAMDISK: gzip image found at block 0 EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities EXT4-fs (ram0): mounted filesystem without journal. Opts: (null) VFS: Mounted root (ext4 filesystem) on device 1:0. devtmpfs: mounted Freeing unused kernel memory: 1024K (c0a00000 - c0b00000) EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr random: dd urandom read with 0 bits of entropy available ubi0: attaching mtd2 ubi0: scanning is finished ubi0: attached mtd2 (name "configs", size 8 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 2526/1770, WL threshold: 4096, image sequence number: 1630723424 ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40 ubi0: background thread "ubi_bgt0d" started, PID 708 UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711 UBIFS (ubi0:0): recovery needed UBIFS (ubi0:0): recovery completed UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs" UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs) UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB) UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 3A5F7F33-7842-4390-8049-C51AC692E364, small LPT model ubi1: attaching mtd5 ubi1: scanning is finished ubi1: attached mtd5 (name "reserve1", size 128 MiB) ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0 ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128 ubi1: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 2268046367 ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36 ubi1: background thread "ubi_bgt1d" started, PID 720 UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723 UBIFS (ubi1:0): recovery needed UBIFS (ubi1:0): recovery completed UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1" UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs) UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB) UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID FC1E0140-0911-4CF8-BD4A-58832F392306, small LPT model IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz macb e000b000.ethernet eth0: link up (100/Full) IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready In axi fpga driver! request_mem_region OK! AXI fpga dev virtual address is 0xcfb38000 *base_vir_addr = 0xab00d In fpga mem driver! request_mem_region OK! fpga mem virtual address is 0xd2000000 main.c:13999: log_level = 4 main.c:14026: This is XILINX board. Totalram: 239353856 main.c:14044: Detect 256MB control board of XILINX driver-bitmain.c:1777: mmap axi_fpga_addr = 0xb6ff1000 driver-bitmain.c:1782: axi_fpga_addr data = 0xb00d driver-bitmain.c:1798: mmap fpga_mem_addr = 0xb5df5000 driver-bitmain.c:995: forceFreq=-1 forceFlag=0 driver-bitmain.c:1697: min work minertest[0]:912
main.c:8490: DETECT HW version=000ab00d main.c:14071: miner ID : 802c742a7910481c main.c:14100: Miner Type = S9+ main.c:14108: AsicType = 1387 main.c:14111: real AsicNum = 84 main.c:14204: use critical mode to search freq... driver-bitmain.c:1877: get PLUG ON=0x00000007 driver-bitmain.c:1947: Find hashboard on Chain[0] driver-bitmain.c:1947: Find hashboard on Chain[1] driver-bitmain.c:1947: Find hashboard on Chain[2] main.c:2148: chain[0] PIC jump to app main.c:2153: Check chain[0] PIC fw version=0xa4 main.c:2148: chain[1] PIC jump to app main.c:2153: Check chain[1] PIC fw version=0xa4 main.c:2148: chain[2] PIC jump to app main.c:2153: Check chain[2] PIC fw version=0xa4 main.c:8805: Chain[0] read_freq_badcores : 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff main.c:8817: chain[0]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] main.c:8836: chain[0]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] main.c:9068: chain[0] has no freq in PIC! Will use default freq=0 and jump over... main.c:8805: Chain[1] read_freq_badcores : 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff main.c:8817: chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] main.c:8836: chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] main.c:9068: chain[1] has no freq in PIC! Will use default freq=0 and jump over... main.c:8805: Chain[2] read_freq_badcores : 0x7d 0xd9 0x56 0x4e 0x52 0x4e 0x56 0x52 0x52 0x56 0x4e 0x52 0x56 0x4e 0x56 0x4e 0x52 0x56 0x4e 0x52 0x52 0x4e 0x56 0x4e 0x56 0x52 0x4e 0x56 0x52 0x56 0x4e 0x52 0x4e 0x52 0x56 0x52 0x56 0x4e 0x4e 0x56 0x52 0x4e 0x52 0x56 0x52 0x4e 0x56 0x4e 0x52 0x56 0x52 0x4e 0x56 0x52 0x56 0x4e 0x56 0x52 0x4e 0x4e 0x56 0x52 0x4e 0x56 0x52 0x4e 0x52 0x56 0x56 0x4e 0x52 0x56 0x4e 0x52 0x52 0x56 0x4e 0x4e 0x56 0x52 0x56 0x4e 0x52 0x52 0x56 0x4e 0x6a 0x19 0x00 0x00 0xc8 0xef 0xbe 0xef 0xbe 0xff 0xee 0xbb 0xff 0xee 0xfb 0xfb 0xee 0xef 0xee 0xef 0xfb 0xeb 0xbf 0xfb 0xfe 0xfa 0xb7 0x11 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff main.c:8817: chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] main.c:8836: chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] main.c:8923: has freq in PIC, will disable freq setting. main.c:8997: chain[2] has freq in PIC and will jump over... main.c:8999: Chain[2] has core num in PIC main.c:9103: get PIC voltage=97 on chain[0], value=750 main.c:9103: get PIC voltage=97 on chain[1], value=750 main.c:9103: get PIC voltage=0 on chain[2], value=930 main.c:9269: chain[0] temp offset record: 4,0,0,0,0,0,40,28 main.c:9286: chain[0] temp chip I2C addr=0x98 main.c:9269: chain[1] temp offset record: -1,-1,-1,-1,-1,-1,-1,-1 main.c:9286: chain[1] temp chip I2C addr=0x98 main.c:9269: chain[2] temp offset record: -1,-1,-1,-1,-1,-1,-1,-1 main.c:9286: chain[2] temp chip I2C addr=0x98 main.c:13963: total_exist_chain_num = 3 main.c:14645: restart Miner chance num=0 main.c:14685: waiting for receive_func to exit! main.c:14699: waiting for pic heart to exit! main.c:13934: bmminer not found= 1087 root 2156 S grep bmminer
main.c:14743: bmminer not found, restart bmminer ... driver-btm-c5.c:12241:bitmain_c5_init: This is the first time running after searching freq! driver-btm-c5.c:12301:bitmain_c5_init: Detect 256MB control board of XILINX driver-btm-c5.c:12320:bitmain_c5_init: Miner Type = S9+ driver-btm-c5.c:12327:bitmain_c5_init: Miner compile time: Tue Mar 19 14:29:33 CST 2019 type: Antminer S11 driver-btm-c5.c:12407:bitmain_c5_init: miner ID : 802c742a7910481c driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=4560 driver-btm-c5.c:12564:bitmain_c5_init: Checking fans... driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=4440 driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=4560 driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=4440 driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=4560 driver-btm-c5.c:3007:check_fan_beforeInit: get fan[0] speed=4440 driver-btm-c5.c:3007:check_fan_beforeInit: get fan[1] speed=4560 driver-btm-c5.c:1767:jump_to_app_CheckAndRestorePIC_T9_18: chain[0] PIC jump to app driver-btm-c5.c:1768:jump_to_app_CheckAndRestorePIC_T9_18: chain[0] PIC jump to app driver-btm-c5.c:1773:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[0] PIC fw version=0xa4 driver-btm-c5.c:13017:bitmain_c5_init: Chain[0] read_freq_badcores : 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff driver-btm-c5.c:13067:bitmain_c5_init: S9+: use voltage limit rules on single board! driver-btm-c5.c:13071:bitmain_c5_init: S9+ fix Chain[J1] test patten OK temp=60 driver-btm-c5.c:1767:jump_to_app_CheckAndRestorePIC_T9_18: chain[1] PIC jump to app driver-btm-c5.c:1768:jump_to_app_CheckAndRestorePIC_T9_18: chain[1] PIC jump to app driver-btm-c5.c:1773:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[1] PIC fw version=0xa4 driver-btm-c5.c:13017:bitmain_c5_init: Chain[1] read_freq_badcores : 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff driver-btm-c5.c:13067:bitmain_c5_init: S9+: use voltage limit rules on single board! driver-btm-c5.c:13071:bitmain_c5_init: S9+ fix Chain[J2] test patten OK temp=60 driver-btm-c5.c:1767:jump_to_app_CheckAndRestorePIC_T9_18: chain[2] PIC jump to app driver-btm-c5.c:1768:jump_to_app_CheckAndRestorePIC_T9_18: chain[2] PIC jump to app driver-btm-c5.c:1773:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[2] PIC fw version=0xa4 driver-btm-c5.c:13017:bitmain_c5_init: Chain[2] read_freq_badcores : 0x7d 0xd9 0x56 0x4e 0x52 0x4e 0x56 0x52 0x52 0x56 0x4e 0x52 0x56 0x4e 0x56 0x4e 0x52 0x56 0x4e 0x52 0x52 0x4e 0x56 0x4e 0x56 0x52 0x4e 0x56 0x52 0x56 0x4e 0x52 0x4e 0x52 0x56 0x52 0x56 0x4e 0x4e 0x56 0x52 0x4e 0x52 0x56 0x52 0x4e 0x56 0x4e 0x52 0x56 0x52 0x4e 0x56 0x52 0x56 0x4e 0x56 0x52 0x4e 0x4e 0x56 0x52 0x4e 0x56 0x52 0x4e 0x52 0x56 0x56 0x4e 0x52 0x56 0x4e 0x52 0x52 0x56 0x4e 0x4e 0x56 0x52 0x56 0x4e 0x52 0x52 0x56 0x4e 0x6a 0x19 0x00 0x00 0xc8 0xef 0xbe 0xef 0xbe 0xff 0xee 0xbb 0xff 0xee 0xfb 0xfb 0xee 0xef 0xee 0xef 0xfb 0xeb 0xbf 0xfb 0xfe 0xfa 0xb7 0x11 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff driver-btm-c5.c:13056:bitmain_c5_init: Chain[J3] has backup chain_voltage=1085 power.c:238:set_fixed_voltage: s9_84_fixed_voltage = 10.850000 driver-btm-c5.c:13067:bitmain_c5_init: S9+: use voltage limit rules on single board! driver-btm-c5.c:13071:bitmain_c5_init: S9+ fix Chain[J3] test patten OK temp=60 driver-btm-c5.c:12200:init_exist_chain_table: total_exist_chain_num = 3 power.c:148:power_check_protocal_type: power protocal f5, using package cmd power.c:173:power_type_detect: start detect power type power.c:181:power_type_detect: init gpio907 power.c:211:power_type_detect: power type is APW8 new type power.c:587:get_min_voltage: board[1] voltage: 9.777539 power.c:587:get_min_voltage: board[2] voltage: 9.764648 power.c:587:get_min_voltage: board[0] voltage: 9.758203 power.c:593:get_min_voltage: min voltage: 9.758203 power.c:349:get_power_iic_value_from_voltage: iic_index for voltage[60] = 10 power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=60 power.c:587:get_min_voltage: board[1] voltage: 10.931250 power.c:587:get_min_voltage: board[2] voltage: 10.895801 power.c:587:get_min_voltage: board[0] voltage: 10.889355 power.c:593:get_min_voltage: min voltage: 10.889355 power.c:370:voltage_tunning: last_iic_data = 60 power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=44 power.c:587:get_min_voltage: board[1] voltage: 11.018262 power.c:587:get_min_voltage: board[2] voltage: 10.998926 power.c:587:get_min_voltage: board[0] voltage: 10.976367 power.c:593:get_min_voltage: min voltage: 10.976367 power.c:370:voltage_tunning: last_iic_data = 44 power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=36 power.c:587:get_min_voltage: board[1] voltage: 11.069824 power.c:587:get_min_voltage: board[2] voltage: 11.037598 power.c:587:get_min_voltage: board[0] voltage: 11.021484 power.c:593:get_min_voltage: min voltage: 11.021484 power.c:370:voltage_tunning: last_iic_data = 36 power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=35 power.c:587:get_min_voltage: board[1] voltage: 11.085938 power.c:587:get_min_voltage: board[2] voltage: 11.060156 power.c:587:get_min_voltage: board[0] voltage: 11.031152 power.c:593:get_min_voltage: min voltage: 11.031152 power.c:370:voltage_tunning: last_iic_data = 35 power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=35 power.c:587:get_min_voltage: board[1] voltage: 11.076270 power.c:587:get_min_voltage: board[2] voltage: 11.050488 power.c:587:get_min_voltage: board[0] voltage: 11.024707 power.c:593:get_min_voltage: min voltage: 11.024707 power.c:370:voltage_tunning: last_iic_data = 35 power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=34 power.c:587:get_min_voltage: board[1] voltage: 11.079492 power.c:587:get_min_voltage: board[2] voltage: 11.056934 power.c:587:get_min_voltage: board[0] voltage: 11.037598 power.c:593:get_min_voltage: min voltage: 11.037598 power.c:370:voltage_tunning: last_iic_data = 34 power.c:376:voltage_tunning: It's very close to target voltage, stop tunning power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=34 power.c:587:get_min_voltage: board[1] voltage: 11.082715 power.c:587:get_min_voltage: board[2] voltage: 11.056934 power.c:587:get_min_voltage: board[0] voltage: 11.040820 power.c:593:get_min_voltage: min voltage: 11.040820 power.c:370:voltage_tunning: last_iic_data = 34 power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.900000, N=50 power.c:587:get_min_voltage: board[1] voltage: 10.989258 power.c:587:get_min_voltage: board[2] voltage: 10.969922 power.c:587:get_min_voltage: board[0] voltage: 10.947363 power.c:593:get_min_voltage: min voltage: 10.947363 power.c:370:voltage_tunning: last_iic_data = 50 power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.900000, N=52 power.c:587:get_min_voltage: board[1] voltage: 10.969922 power.c:587:get_min_voltage: board[2] voltage: 10.963477 power.c:587:get_min_voltage: board[0] voltage: 10.928027 power.c:593:get_min_voltage: min voltage: 10.928027 power.c:370:voltage_tunning: last_iic_data = 52 power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.900000, N=53 power.c:587:get_min_voltage: board[1] voltage: 10.976367 power.c:587:get_min_voltage: board[2] voltage: 10.947363 power.c:587:get_min_voltage: board[0] voltage: 10.918359 power.c:593:get_min_voltage: min voltage: 10.918359 power.c:370:voltage_tunning: last_iic_data = 53 power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.900000, N=53 power.c:587:get_min_voltage: board[1] voltage: 10.966699 power.c:587:get_min_voltage: board[2] voltage: 10.944141 power.c:587:get_min_voltage: board[0] voltage: 10.928027 power.c:593:get_min_voltage: min voltage: 10.928027 power.c:370:voltage_tunning: last_iic_data = 53 power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.900000, N=54 power.c:587:get_min_voltage: board[1] voltage: 10.969922 power.c:587:get_min_voltage: board[2] voltage: 10.940918 power.c:587:get_min_voltage: board[0] voltage: 10.934473 power.c:593:get_min_voltage: min voltage: 10.934473 power.c:370:voltage_tunning: last_iic_data = 54 power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.900000, N=56 power.c:587:get_min_voltage: board[1] voltage: 10.947363 power.c:587:get_min_voltage: board[2] voltage: 10.931250 power.c:587:get_min_voltage: board[0] voltage: 10.921582 power.c:593:get_min_voltage: min voltage: 10.921582 power.c:370:voltage_tunning: last_iic_data = 56 power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.900000, N=57 power.c:587:get_min_voltage: board[1] voltage: 10.937695 power.c:587:get_min_voltage: board[2] voltage: 10.921582 power.c:587:get_min_voltage: board[0] voltage: 10.911914 power.c:593:get_min_voltage: min voltage: 10.911914 power.c:370:voltage_tunning: last_iic_data = 57 power.c:376:voltage_tunning: It's very close to target voltage, stop tunning power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.900000, N=57 driver-btm-c5.c:2810:enable_pic_dac: echo 0 > /sys/class/gpio/gpio907/value driver-btm-c5.c:2810:enable_pic_dac: echo 0 > /sys/class/gpio/gpio907/value driver-btm-c5.c:2810:enable_pic_dac: echo 0 > /sys/class/gpio/gpio907/value driver-btm-c5.c:13298:bitmain_c5_init: Chain[J1] orignal chain_voltage_pic=97 value=750 driver-btm-c5.c:13298:bitmain_c5_init: Chain[J2] orignal chain_voltage_pic=97 value=750 driver-btm-c5.c:13298:bitmain_c5_init: Chain[J3] orignal chain_voltage_pic=0 value=930 driver-btm-c5.c:13315:bitmain_c5_init: Chain[J3] will use backup chain_voltage_pic=1085 [0] driver-btm-c5.c:13325:bitmain_c5_init: Chain[J3] get working chain_voltage_pic=0 driver-btm-c5.c:13416:bitmain_c5_init: Chain[J1] has 84 asic driver-btm-c5.c:13416:bitmain_c5_init: Chain[J2] has 84 asic driver-btm-c5.c:13416:bitmain_c5_init: Chain[J3] has 84 asic driver-btm-c5.c:4480:set_frequency: Chain[J1] has no freq in PIC, set default freq=600M driver-btm-c5.c:4541:set_frequency: Chain[J1] has no core num in PIC driver-btm-c5.c:4480:set_frequency: Chain[J2] has no freq in PIC, set default freq=600M driver-btm-c5.c:4541:set_frequency: Chain[J2] has no core num in PIC driver-btm-c5.c:4541:set_frequency: Chain[J3] has no core num in PIC driver-btm-c5.c:3765:get_total_rate_from_eeprom: totalrate = 6504 driver-btm-c5.c:4588:set_frequency: miner total rate=6504GH/s ideal_total_hash_rate = 6500GH/s driver-btm-c5.c:4613:set_frequency: read PIC voltage=750 on chain[0] driver-btm-c5.c:4615:set_frequency: Chain:0 chipnum=84 driver-btm-c5.c:4633:set_frequency: S9+ can not record Chain[J1] voltage added value driver-btm-c5.c:4757:set_frequency: Chain:0 base freq=600 Asic[ 0]:600 Asic[ 1]:600 Asic[ 2]:600 Asic[ 3]:600 Asic[ 4]:600 Asic[ 5]:600 Asic[ 6]:600 Asic[ 7]:600 Asic[ 8]:600 Asic[ 9]:600 Asic[10]:600 Asic[11]:600 Asic[12]:600 Asic[13]:600 Asic[14]:600 Asic[15]:600 Asic[16]:600 Asic[17]:600 Asic[18]:600 Asic[19]:600 Asic[20]:600 Asic[21]:600 Asic[22]:600 Asic[23]:600 Asic[24]:600 Asic[25]:600 Asic[26]:600 Asic[27]:600 Asic[28]:600 Asic[29]:600 Asic[30]:600 Asic[31]:600 Asic[32]:600 Asic[33]:600 Asic[34]:600 Asic[35]:600 Asic[36]:600 Asic[37]:600 Asic[38]:600 Asic[39]:600 Asic[40]:600 Asic[41]:600 Asic[42]:600 Asic[43]:600 Asic[44]:600 Asic[45]:600 Asic[46]:600 Asic[47]:600 Asic[48]:600 Asic[49]:600 Asic[50]:600 Asic[51]:600 Asic[52]:600 Asic[53]:600 Asic[54]:600 Asic[55]:600 Asic[56]:600 Asic[57]:600 Asic[58]:600 Asic[59]:600 Asic[60]:600 Asic[61]:600 Asic[62]:600 Asic[63]:600 Asic[64]:600 Asic[65]:600 Asic[66]:600 Asic[67]:600 Asic[68]:600 Asic[69]:600 Asic[70]:600 Asic[71]:600 Asic[72]:600 Asic[73]:600 Asic[74]:600 Asic[75]:600 Asic[76]:600 Asic[77]:600 Asic[78]:600 Asic[79]:600 Asic[80]:600 Asic[81]:600 Asic[82]:600 Asic[83]:600 driver-btm-c5.c:4826:set_frequency: Chain:0 max freq=600 driver-btm-c5.c:4827:set_frequency: Chain:0 min freq=600
driver-btm-c5.c:4613:set_frequency: read PIC voltage=750 on chain[1] driver-btm-c5.c:4615:set_frequency: Chain:1 chipnum=84 driver-btm-c5.c:4633:set_frequency: S9+ can not record Chain[J2] voltage added value driver-btm-c5.c:4757:set_frequency: Chain:1 base freq=600 Asic[ 0]:600 Asic[ 1]:600 Asic[ 2]:600 Asic[ 3]:600 Asic[ 4]:600 Asic[ 5]:600 Asic[ 6]:600 Asic[ 7]:600 Asic[ 8]:600 Asic[ 9]:600 Asic[10]:600 Asic[11]:600 Asic[12]:600 Asic[13]:600 Asic[14]:600 Asic[15]:600 Asic[16]:600 Asic[17]:600 Asic[18]:600 Asic[19]:600 Asic[20]:600 Asic[21]:600 Asic[22]:600 Asic[23]:600 Asic[24]:600 Asic[25]:600 Asic[26]:600 Asic[27]:600 Asic[28]:600 Asic[29]:600 Asic[30]:600 Asic[31]:600 Asic[32]:600 Asic[33]:600 Asic[34]:600 Asic[35]:600 Asic[36]:600 Asic[37]:600 Asic[38]:600 Asic[39]:600 Asic[40]:600 Asic[41]:600 Asic[42]:600 Asic[43]:600 Asic[44]:600 Asic[45]:600 Asic[46]:600 Asic[47]:600 Asic[48]:600 Asic[49]:600 Asic[50]:600 Asic[51]:600 Asic[52]:600 Asic[53]:600 Asic[54]:600 Asic[55]:600 Asic[56]:600 Asic[57]:600 Asic[58]:600 Asic[59]:600 Asic[60]:600 Asic[61]:600 Asic[62]:600 Asic[63]:600 Asic[64]:600 Asic[65]:600 Asic[66]:600 Asic[67]:600 Asic[68]:600 Asic[69]:600 Asic[70]:600 Asic[71]:600 Asic[72]:600 Asic[73]:600 Asic[74]:600 Asic[75]:600 Asic[76]:600 Asic[77]:600 Asic[78]:600 Asic[79]:600 Asic[80]:600 Asic[81]:600 Asic[82]:600 Asic[83]:600 driver-btm-c5.c:4826:set_frequency: Chain:1 max freq=600 driver-btm-c5.c:4827:set_frequency: Chain:1 min freq=600
driver-btm-c5.c:4613:set_frequency: read PIC voltage=930 on chain[2] driver-btm-c5.c:4615:set_frequency: Chain:2 chipnum=84 driver-btm-c5.c:4633:set_frequency: S9+ can not record Chain[J3] voltage added value driver-btm-c5.c:4757:set_frequency: Chain:2 base freq=600 Asic[ 0]:725 Asic[ 1]:675 Asic[ 2]:700 Asic[ 3]:675 Asic[ 4]:725 Asic[ 5]:700 Asic[ 6]:700 Asic[ 7]:725 Asic[ 8]:675 Asic[ 9]:700 Asic[10]:725 Asic[11]:675 Asic[12]:725 Asic[13]:675 Asic[14]:700 Asic[15]:725 Asic[16]:675 Asic[17]:700 Asic[18]:700 Asic[19]:675 Asic[20]:725 Asic[21]:675 Asic[22]:725 Asic[23]:700 Asic[24]:675 Asic[25]:725 Asic[26]:700 Asic[27]:725 Asic[28]:675 Asic[29]:700 Asic[30]:675 Asic[31]:700 Asic[32]:725 Asic[33]:700 Asic[34]:725 Asic[35]:675 Asic[36]:675 Asic[37]:725 Asic[38]:700 Asic[39]:675 Asic[40]:700 Asic[41]:725 Asic[42]:700 Asic[43]:675 Asic[44]:725 Asic[45]:675 Asic[46]:700 Asic[47]:725 Asic[48]:700 Asic[49]:675 Asic[50]:725 Asic[51]:700 Asic[52]:725 Asic[53]:675 Asic[54]:725 Asic[55]:700 Asic[56]:675 Asic[57]:675 Asic[58]:725 Asic[59]:700 Asic[60]:675 Asic[61]:725 Asic[62]:700 Asic[63]:675 Asic[64]:700 Asic[65]:725 Asic[66]:725 Asic[67]:675 Asic[68]:700 Asic[69]:725 Asic[70]:675 Asic[71]:700 Asic[72]:700 Asic[73]:725 Asic[74]:675 Asic[75]:675 Asic[76]:725 Asic[77]:700 Asic[78]:725 Asic[79]:675 Asic[80]:700 Asic[81]:700 Asic[82]:725 Asic[83]:675 driver-btm-c5.c:4826:set_frequency: Chain:2 max freq=725 driver-btm-c5.c:4827:set_frequency: Chain:2 min freq=675
driver-btm-c5.c:4836:set_frequency: Miner fix freq ... driver-btm-c5.c:4871:set_frequency: read PIC voltage=750 on chain[0] driver-btm-c5.c:4872:set_frequency: Chain:0 chipnum=84 driver-btm-c5.c:4889:set_frequency: S9+ can not record Chain[J1] voltage added value driver-btm-c5.c:5037:set_frequency: Chain:0 base freq=600 Asic[ 0]:600 Asic[ 1]:600 Asic[ 2]:600 Asic[ 3]:600 Asic[ 4]:600 Asic[ 5]:600 Asic[ 6]:600 Asic[ 7]:600 Asic[ 8]:600 Asic[ 9]:600 Asic[10]:600 Asic[11]:600 Asic[12]:600 Asic[13]:600 Asic[14]:600 Asic[15]:600 Asic[16]:600 Asic[17]:600 Asic[18]:600 Asic[19]:600 Asic[20]:600 Asic[21]:600 Asic[22]:600 Asic[23]:600 Asic[24]:600 Asic[25]:600 Asic[26]:600 Asic[27]:600 Asic[28]:600 Asic[29]:600 Asic[30]:600 Asic[31]:600 Asic[32]:600 Asic[33]:600 Asic[34]:600 Asic[35]:600 Asic[36]:600 Asic[37]:600 Asic[38]:600 Asic[39]:600 Asic[40]:600 Asic[41]:600 Asic[42]:600 Asic[43]:600 Asic[44]:600 Asic[45]:600 Asic[46]:600 Asic[47]:600 Asic[48]:600 Asic[49]:600 Asic[50]:600 Asic[51]:600 Asic[52]:600 Asic[53]:600 Asic[54]:600 Asic[55]:600 Asic[56]:600 Asic[57]:600 Asic[58]:600 Asic[59]:600 Asic[60]:600 Asic[61]:600 Asic[62]:600 Asic[63]:600 Asic[64]:600 Asic[65]:600 Asic[66]:600 Asic[67]:600 Asic[68]:600 Asic[69]:600 Asic[70]:600 Asic[71]:600 Asic[72]:600 Asic[73]:600 Asic[74]:600 Asic[75]:600 Asic[76]:600 Asic[77]:600 Asic[78]:600 Asic[79]:600 Asic[80]:600 Asic[81]:600 Asic[82]:600 Asic[83]:600 driver-btm-c5.c:5127:set_frequency: Chain:0 max freq=600 driver-btm-c5.c:5128:set_frequency: Chain:0 min freq=600
driver-btm-c5.c:4871:set_frequency: read PIC voltage=750 on chain[1] driver-btm-c5.c:4872:set_frequency: Chain:1 chipnum=84 driver-btm-c5.c:4889:set_frequency: S9+ can not record Chain[J2] voltage added value driver-btm-c5.c:5037:set_frequency: Chain:1 base freq=600 Asic[ 0]:600 Asic[ 1]:600 Asic[ 2]:600 Asic[ 3]:600 Asic[ 4]:600 Asic[ 5]:600 Asic[ 6]:600 Asic[ 7]:600 Asic[ 8]:600 Asic[ 9]:600 Asic[10]:600 Asic[11]:600 Asic[12]:600 Asic[13]:600 Asic[14]:600 Asic[15]:600 Asic[16]:600 Asic[17]:600 Asic[18]:600 Asic[19]:600 Asic[20]:600 Asic[21]:600 Asic[22]:600 Asic[23]:600 Asic[24]:600 Asic[25]:600 Asic[26]:600 Asic[27]:600 Asic[28]:600 Asic[29]:600 Asic[30]:600 Asic[31]:600 Asic[32]:600 Asic[33]:600 Asic[34]:600 Asic[35]:600 Asic[36]:600 Asic[37]:600 Asic[38]:600 Asic[39]:600 Asic[40]:600 Asic[41]:600 Asic[42]:600 Asic[43]:600 Asic[44]:600 Asic[45]:600 Asic[46]:600 Asic[47]:600 Asic[48]:600 Asic[49]:600 Asic[50]:600 Asic[51]:600 Asic[52]:600 Asic[53]:600 Asic[54]:600 Asic[55]:600 Asic[56]:600 Asic[57]:600 Asic[58]:600 Asic[59]:600 Asic[60]:600 Asic[61]:600 Asic[62]:600 Asic[63]:600 Asic[64]:600 Asic[65]:600 Asic[66]:600 Asic[67]:600 Asic[68]:600 Asic[69]:600 Asic[70]:600 Asic[71]:600 Asic[72]:600 Asic[73]:600 Asic[74]:600 Asic[75]:600 Asic[76]:600 Asic[77]:600 Asic[78]:600 Asic[79]:600 Asic[80]:600 Asic[81]:600 Asic[82]:600 Asic[83]:600 driver-btm-c5.c:5127:set_frequency: Chain:1 max freq=600 driver-btm-c5.c:5128:set_frequency: Chain:1 min freq=600
driver-btm-c5.c:4871:set_frequency: read PIC voltage=930 on chain[2] driver-btm-c5.c:4872:set_frequency: Chain:2 chipnum=84 driver-btm-c5.c:4889:set_frequency: S9+ can not record Chain[J3] voltage added value driver-btm-c5.c:5037:set_frequency: Chain:2 base freq=600 Asic[ 0]:725 Asic[ 1]:675 Asic[ 2]:700 Asic[ 3]:675 Asic[ 4]:725 Asic[ 5]:700 Asic[ 6]:700 Asic[ 7]:725 Asic[ 8]:675 Asic[ 9]:700 Asic[10]:725 Asic[11]:675 Asic[12]:725 Asic[13]:675 Asic[14]:700 Asic[15]:725 Asic[16]:675 Asic[17]:700 Asic[18]:700 Asic[19]:675 Asic[20]:725 Asic[21]:675 Asic[22]:725 Asic[23]:700 Asic[24]:675 Asic[25]:725 Asic[26]:700 Asic[27]:725 Asic[28]:675 Asic[29]:700 Asic[30]:675 Asic[31]:700 Asic[32]:725 Asic[33]:700 Asic[34]:725 Asic[35]:675 Asic[36]:675 Asic[37]:725 Asic[38]:700 Asic[39]:675 Asic[40]:700 Asic[41]:725 Asic[42]:700 Asic[43]:675 Asic[44]:725 Asic[45]:675 Asic[46]:700 Asic[47]:725 Asic[48]:700 Asic[49]:675 Asic[50]:725 Asic[51]:700 Asic[52]:725 Asic[53]:675 Asic[54]:725 Asic[55]:700 Asic[56]:675 Asic[57]:675 Asic[58]:725 Asic[59]:700 Asic[60]:675 Asic[61]:725 Asic[62]:700 Asic[63]:675 Asic[64]:700 Asic[65]:725 Asic[66]:725 Asic[67]:675 Asic[68]:700 Asic[69]:725 Asic[70]:675 Asic[71]:700 Asic[72]:700 Asic[73]:725 Asic[74]:675 Asic[75]:675 Asic[76]:725 Asic[77]:700 Asic[78]:725 Asic[79]:675 Asic[80]:700 Asic[81]:700 Asic[82]:725 Asic[83]:675 driver-btm-c5.c:5127:set_frequency: Chain:2 max freq=725 driver-btm-c5.c:5128:set_frequency: Chain:2 min freq=675
driver-btm-c5.c:5136:set_frequency: max freq = 725 driver-btm-c5.c:3303:set_PWM_according_to_temperature: set_PWM_according_to_temperature: fan set normal mode driver-btm-c5.c:9618:init_uart_baud: set baud=1 driver-btm-c5.c:6610:calibration_sensor_offset: Chain[J1] PIC temp offset: 4,0,0,0,0,0,40,28,0,0,0,0,0,0,0,0,0,0, driver-btm-c5.c:6644:calibration_sensor_offset: chain[1] temp chip I2C addr=0x98 driver-btm-c5.c:6652:calibration_sensor_offset: chain[1] has no middle temp, use special fix mode. driver-btm-c5.c:6677:calibration_sensor_offset: Chain[J1] chip[9] use PIC middle temp offset=0 typeID=00 driver-btm-c5.c:6782:calibration_sensor_offset: Warning: Chain[J1] has no temp offset in PIC! will fix it driver-btm-c5.c:6906:calibration_sensor_offset: Chain[J1] use default temp chip[69] driver-btm-c5.c:6336:do_calibration_sensor_offset: Chain[J1] try read temp chip[69] ID=55 (I2C addr=0x98) driver-btm-c5.c:6401:do_calibration_sensor_offset: New offset Chain[1] chip[69] local:33 remote:36 offset:27 driver-btm-c5.c:6911:calibration_sensor_offset: Chain[J1] chip[69] get middle temp offset=27 typeID=55 driver-btm-c5.c:6906:calibration_sensor_offset: Chain[J1] use default temp chip[132] driver-btm-c5.c:6336:do_calibration_sensor_offset: Chain[J1] try read temp chip[132] ID=55 (I2C addr=0x98) driver-btm-c5.c:6401:do_calibration_sensor_offset: New offset Chain[1] chip[132] local:34 remote:37 offset:28 driver-btm-c5.c:6911:calibration_sensor_offset: Chain[J1] chip[132] get middle temp offset=28 typeID=55 driver-btm-c5.c:6610:calibration_sensor_offset: Chain[J2] PIC temp offset: -1,-1,-1,-1,-1,-1,-1,-1,0,0,0,0,0,0,0,0,0,0, driver-btm-c5.c:6644:calibration_sensor_offset: chain[2] temp chip I2C addr=0x98 driver-btm-c5.c:6652:calibration_sensor_offset: chain[2] has no middle temp, use special fix mode. driver-btm-c5.c:6782:calibration_sensor_offset: Warning: Chain[J2] has no temp offset in PIC! will fix it driver-btm-c5.c:6906:calibration_sensor_offset: Chain[J2] use default temp chip[69] driver-btm-c5.c:6336:do_calibration_sensor_offset: Chain[J2] try read temp chip[69] ID=1a (I2C addr=0x98) driver-btm-c5.c:6394:do_calibration_sensor_offset: Warning: Chain[1] chip[69] local:34 remote:-89 offset:-102, will fixed offset=27 driver-btm-c5.c:6401:do_calibration_sensor_offset: New offset Chain[2] chip[69] local:34 remote:-89 offset:27 driver-btm-c5.c:6911:calibration_sensor_offset: Chain[J2] chip[69] get middle temp offset=27 typeID=1a driver-btm-c5.c:6906:calibration_sensor_offset: Chain[J2] use default temp chip[132] driver-btm-c5.c:6336:do_calibration_sensor_offset: Chain[J2] try read temp chip[132] ID=1a (I2C addr=0x98) driver-btm-c5.c:6394:do_calibration_sensor_offset: Warning: Chain[1] chip[132] local:36 remote:-80 offset:-109, will fixed offset=27 driver-btm-c5.c:6401:do_calibration_sensor_offset: New offset Chain[2] chip[132] local:36 remote:-80 offset:27 driver-btm-c5.c:6911:calibration_sensor_offset: Chain[J2] chip[132] get middle temp offset=27 typeID=1a driver-btm-c5.c:6610:calibration_sensor_offset: Chain[J3] PIC temp offset: -1,-1,-1,-1,-1,-1,-1,-1,0,0,0,0,0,0,0,0,0,0, driver-btm-c5.c:6644:calibration_sensor_offset: chain[3] temp chip I2C addr=0x98 driver-btm-c5.c:6652:calibration_sensor_offset: chain[3] has no middle temp, use special fix mode. driver-btm-c5.c:6782:calibration_sensor_offset: Warning: Chain[J3] has no temp offset in PIC! will fix it driver-btm-c5.c:6906:calibration_sensor_offset: Chain[J3] use default temp chip[69] driver-btm-c5.c:6336:do_calibration_sensor_offset: Chain[J3] try read temp chip[69] ID=1a (I2C addr=0x98) driver-btm-c5.c:6394:do_calibration_sensor_offset: Warning: Chain[2] chip[69] local:34 remote:-89 offset:-102, will fixed offset=27 driver-btm-c5.c:6401:do_calibration_sensor_offset: New offset Chain[3] chip[69] local:34 remote:-89 offset:27 driver-btm-c5.c:6911:calibration_sensor_offset: Chain[J3] chip[69] get middle temp offset=27 typeID=1a driver-btm-c5.c:6906:calibration_sensor_offset: Chain[J3] use default temp chip[132] driver-btm-c5.c:6336:do_calibration_sensor_offset: Chain[J3] try read temp chip[132] ID=1a (I2C addr=0x98) driver-btm-c5.c:6394:do_calibration_sensor_offset: Warning: Chain[2] chip[132] local:37 remote:-86 offset:-102, will fixed offset=27 driver-btm-c5.c:6401:do_calibration_sensor_offset: New offset Chain[3] chip[132] local:37 remote:-86 offset:27 driver-btm-c5.c:6911:calibration_sensor_offset: Chain[J3] chip[132] get middle temp offset=27 typeID=1a driver-btm-c5.c:13746:bitmain_c5_init: open core three times driver-btm-c5.c:13746:bitmain_c5_init: open core three times driver-btm-c5.c:13746:bitmain_c5_init: open core three times driver-btm-c5.c:12108:set_working_voltage: setting to working voltage... power.c:654:set_iic_power_to_working_voltage: setting to working voltage... power.c:587:get_min_voltage: board[1] voltage: 10.895801 power.c:587:get_min_voltage: board[2] voltage: 10.860352 power.c:587:get_min_voltage: board[0] voltage: 10.850684 power.c:593:get_min_voltage: min voltage: 10.850684 power.c:370:voltage_tunning: last_iic_data = 57 power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=41 power.c:587:get_min_voltage: board[1] voltage: 10.998926 power.c:587:get_min_voltage: board[2] voltage: 10.947363 power.c:587:get_min_voltage: board[0] voltage: 10.940918 power.c:593:get_min_voltage: min voltage: 10.940918 power.c:370:voltage_tunning: last_iic_data = 41 power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=33 power.c:587:get_min_voltage: board[1] voltage: 11.018262 power.c:587:get_min_voltage: board[2] voltage: 11.002148 power.c:587:get_min_voltage: board[0] voltage: 10.992480 power.c:593:get_min_voltage: min voltage: 10.992480 power.c:370:voltage_tunning: last_iic_data = 33 power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=29 power.c:587:get_min_voltage: board[1] voltage: 11.044043 power.c:587:get_min_voltage: board[2] voltage: 11.027930 power.c:587:get_min_voltage: board[0] voltage: 11.011816 power.c:593:get_min_voltage: min voltage: 11.011816 power.c:370:voltage_tunning: last_iic_data = 29 power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=27 power.c:587:get_min_voltage: board[1] voltage: 11.060156 power.c:587:get_min_voltage: board[2] voltage: 11.037598 power.c:587:get_min_voltage: board[0] voltage: 11.018262 power.c:593:get_min_voltage: min voltage: 11.018262 power.c:370:voltage_tunning: last_iic_data = 27 power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=25 power.c:587:get_min_voltage: board[1] voltage: 11.073047 power.c:587:get_min_voltage: board[2] voltage: 11.047266 power.c:587:get_min_voltage: board[0] voltage: 11.027930 power.c:593:get_min_voltage: min voltage: 11.027930 power.c:370:voltage_tunning: last_iic_data = 25 power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=24 power.c:587:get_min_voltage: board[1] voltage: 11.073047 power.c:587:get_min_voltage: board[2] voltage: 11.044043 power.c:587:get_min_voltage: board[0] voltage: 11.034375 power.c:593:get_min_voltage: min voltage: 11.034375 power.c:370:voltage_tunning: last_iic_data = 24 power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=24 power.c:587:get_min_voltage: board[1] voltage: 11.073047 power.c:587:get_min_voltage: board[2] voltage: 11.050488 power.c:587:get_min_voltage: board[0] voltage: 11.031152 power.c:593:get_min_voltage: min voltage: 11.031152 power.c:370:voltage_tunning: last_iic_data = 24 power.c:376:voltage_tunning: It's very close to target voltage, stop tunning power.c:626:set_iic_power_voltage: voltage_tunning, set to 10.850000, N=24 driver-btm-c5.c:13949:bitmain_c5_init: start thread for read temp setStartTimePoint total_tv_start_sys=236 total_tv_end_sys=237 driver-btm-c5.c:10333:check_system_work: restartNum = 2 , auto-reinit enabled... driver-btm-c5.c:8743:read_temp_func: bring_up_pcb_temp = 54 do read_temp_func once...
get RT hashrate from Chain[0]: (asic index start from 1-84) Asic[01]=0.00000 Asic[02]=0.00000 Asic[03]=0.00000 Asic[04]=0.00000 Asic[05]=0.00000 Asic[06]=0.00000 Asic[07]=0.00000 Asic[08]=0.00000 Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=0.00000 Asic[15]=0.00000 Asic[16]=0.00000 Asic[17]=0.00000 Asic[18]=0.00000 Asic[19]=0.00000 Asic[20]=0.00000 Asic[21]=0.00000 Asic[22]=0.00000 Asic[23]=0.00000 Asic[24]=0.00000 Asic[25]=0.00000 Asic[26]=0.00000 Asic[27]=0.00000 Asic[28]=0.00000 Asic[29]=0.00000 Asic[30]=0.00000 Asic[31]=0.00000 Asic[32]=0.00000 Asic[33]=0.00000 Asic[34]=0.00000 Asic[35]=0.00000 Asic[36]=0.00000 Asic[37]=0.00000 Asic[38]=0.00000 Asic[39]=21.6760 Asic[40]=0.00000 Asic[41]=0.00000 Asic[42]=0.00000 Asic[43]=0.00000 Asic[44]=0.00000 Asic[45]=0.00000 Asic[46]=0.00000 Asic[47]=0.00000 Asic[48]=0.00000 Asic[49]=0.00000 Asic[50]=0.00000 Asic[51]=0.00000 Asic[52]=0.00000 Asic[53]=0.00000 Asic[54]=0.00000 Asic[55]=0.00000 Asic[56]=0.00000 Asic[57]=0.00000 Asic[58]=0.00000 Asic[59]=0.00000 Asic[60]=0.00000 Asic[61]=0.00000 Asic[62]=0.00000 Asic[63]=0.00000 Asic[64]=0.00000 Asic[65]=0.00000 Asic[66]=0.00000 Asic[67]=0.00000 Asic[68]=0.00000 Asic[69]=0.00000 Asic[70]=0.00000 Asic[71]=0.00000 Asic[72]=0.00000 Asic[73]=0.00000 Asic[74]=0.00000 Asic[75]=0.00000 Asic[76]=20.5180 Asic[77]=0.00000 Asic[78]=15.0990 Asic[79]=0.00000 Asic[80]=0.00000 Asic[81]=0.00000 Asic[82]=0.00000 Asic[83]=0.00000 Asic[84]=0.00000
get RT hashrate from Chain[1]: (asic index start from 1-84) Asic[01]=0.00000 Asic[02]=0.00000 Asic[03]=0.00000 Asic[04]=0.00000 Asic[05]=0.00000 Asic[06]=0.00000 Asic[07]=0.00000 Asic[08]=0.00000 Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=0.00000 Asic[15]=0.00000 Asic[16]=0.00000 Asic[17]=0.00000 Asic[18]=0.00000 Asic[19]=0.00000 Asic[20]=0.00000 Asic[21]=0.00000 Asic[22]=0.00000 Asic[23]=0.00000 Asic[24]=0.00000 Asic[25]=0.00000 Asic[26]=0.00000 Asic[27]=0.00000 Asic[28]=0.00000 Asic[29]=0.00000 Asic[30]=0.00000 Asic[31]=0.00000 Asic[32]=0.00000 Asic[33]=0.00000 Asic[34]=0.00000 Asic[35]=0.00000 Asic[36]=0.00000 Asic[37]=0.00000 Asic[38]=0.00000 Asic[39]=28.1010 Asic[40]=0.00000 Asic[41]=0.00000 Asic[42]=0.00000 Asic[43]=0.00000 Asic[44]=0.00000 Asic[45]=0.00000 Asic[46]=0.00000 Asic[47]=0.00000 Asic[48]=0.00000 Asic[49]=0.00000 Asic[50]=0.00000 Asic[51]=0.00000 Asic[52]=0.00000 Asic[53]=0.00000 Asic[54]=0.00000 Asic[55]=0.00000 Asic[56]=0.00000 Asic[57]=0.00000 Asic[58]=0.00000 Asic[59]=0.00000 Asic[60]=0.00000 Asic[61]=0.00000 Asic[62]=0.00000 Asic[63]=0.00000 Asic[64]=0.00000 Asic[65]=0.00000 Asic[66]=0.00000 Asic[67]=0.00000 Asic[68]=0.00000 Asic[69]=0.00000 Asic[70]=0.00000 Asic[71]=0.00000 Asic[72]=0.00000 Asic[73]=0.00000 Asic[74]=0.00000 Asic[75]=0.00000 Asic[76]=26.5750 Asic[77]=0.00000 Asic[78]=488.837 Asic[79]=0.00000 Asic[80]=0.00000 Asic[81]=0.00000 Asic[82]=0.00000 Asic[83]=0.00000 Asic[84]=0.00000
get RT hashrate from Chain[2]: (asic index start from 1-84) Asic[01]=57.7130 Asic[02]=63.8870 Asic[03]=73.5510 Asic[04]=52.0760 Asic[05]=88.3150 Asic[06]=63.0820 Asic[07]=80.5300 Asic[08]=87.2410 Asic[09]=60.3970 Asic[10]=53.9550 Asic[11]=91.2680 Asic[12]=67.6450 Asic[13]=49.9280 Asic[14]=42.9490 Asic[15]=50.1970 Asic[16]=101.200 Asic[17]=49.6600 Asic[18]=75.4300 Asic[19]=68.7190 Asic[20]=65.7660 Asic[21]=67.1080 Asic[22]=80.7990 Asic[23]=98.2470 Asic[24]=63.3500 Asic[25]=73.2820 Asic[26]=42.1440 Asic[27]=27.3800 Asic[28]=54.2230 Asic[29]=73.8190 Asic[30]=39.4600 Asic[31]=73.5510 Asic[32]=50.4650 Asic[33]=58.5180 Asic[34]=37.0440 Asic[35]=68.4510 Asic[36]=90.9990 Asic[37]=53.6870 Asic[38]=84.0200 Asic[39]=43.2680 Asic[40]=52.8810 Asic[41]=80.5300 Asic[42]=78.6510 Asic[43]=41.0700 Asic[44]=49.9280 Asic[45]=75.4300 Asic[46]=53.4180 Asic[47]=68.4510 Asic[48]=77.0400 Asic[49]=49.3920 Asic[50]=86.7040 Asic[51]=84.8250 Asic[52]=89.6570 Asic[53]=56.9080 Asic[54]=55.5660 Asic[55]=35.1650 Asic[56]=49.9280 Asic[57]=56.1030 Asic[58]=108.984 Asic[59]=92.0730 Asic[60]=47.7810 Asic[61]=39.4600 Asic[62]=47.7810 Asic[63]=70.0610 Asic[64]=97.9780 Asic[65]=71.4030 Asic[66]=55.5660 Asic[67]=62.0080 Asic[68]=84.2880 Asic[69]=52.8810 Asic[70]=82.6780 Asic[71]=49.1230 Asic[72]=39.9960 Asic[73]=80.2620 Asic[74]=69.5240 Asic[75]=50.4650 Asic[76]=43.0330 Asic[77]=89.6570 Asic[78]=7805.50 Asic[79]=65.4980 Asic[80]=69.2560 Asic[81]=65.2290 Asic[82]=76.7720 Asic[83]=65.2290 Asic[84]=41.8750 Check Chain[J1] ASIC RT error: (asic index start from 1-84) Check Chain[J2] ASIC RT error: (asic index start from 1-84) Asic[78]=488.837000 Check Chain[J3] ASIC RT error: (asic index start from 1-84) Asic[16]=101.200000 Asic[58]=108.984000 Asic[78]=7805.500000 Done check_asic_reg Chain[0] Chip[69] pcb temperature=39 Chain[0] Chip[18] junction temperature=49 Special fix Chain[0] Chip[18] middle Temp = 54 Chain[0] Chip[132] pcb temperature=51 Chain[0] Chip[34] junction temperature=61 Special fix Chain[0] Chip[34] middle Temp = 66 Done read temp on Chain[0] Chain[1] Chip[69] pcb temperature=41 Chain[1] Chip[18] junction temperature=113 Special fix Chain[1] Chip[18] middle Temp = 56 Chain[1] Chip[132] pcb temperature=53 Chain[1] Chip[34] junction temperature=137 Special fix Chain[1] Chip[34] middle Temp = 68 Done read temp on Chain[1] Chain[2] Chip[69] pcb temperature=42 Chain[2] Chip[18] junction temperature=119 Special fix Chain[2] Chip[18] middle Temp = 57 Chain[2] Chip[132] pcb temperature=54 Chain[2] Chip[34] junction temperature=135 Special fix Chain[2] Chip[34] middle Temp = 69 Done read temp on Chain[2] Max pcb temp : 54 FAN PWM: 88 read_temp_func Done! CRC error counter=0
|
|
|
Hello I have v9 board control And I want to use it on other new miners Because they are similar in terms of hardware First: I replaced the control board program with the s15 Downgrade file Now the board control can be used for s15 is there a problem The new miners have power control output My question is: Where can I find this power control output on the v9 controlboard thanks
|
|
|
hi i have dragon t1 what i do to overclock??? must change framware?
|
|
|
I think that is incorrect, they literally have a tool that accepts the firmware of all the following models (S9.S9j.S9k.S9se.S11. S15.T15.S17.T17) and I am not aware of any control board that is available to the masses which can do that. correct me if I am wrong. Hello You are completely right The repair tool is literally an s9 control board with an SD card image running the diagnostic software hooked up to a screen. You can get a copy of the SD card on the internet somewhere
hi This is not the case at all If you buy the S9 or V9 board control And copy the files into the SD card The final output is something different from the tester They are similar in appearance but are practically different I tested it doesn't work You have to buy the tester yourself from a Chinese company if you want
|
|
|
hi i have this tester
You can't copy the tester at all The tester still does not work by adding tf card files If it weren't for that, everyone would make a tester for themselves And no one buys the tester from Chinese sites ........................ So Buy a device and relax It's worth it
|
|
|
hi. thanks for t9 hex file uploading.
|
|
|
thanks i i have tnm 5000 prgrammer i can read hex file from hashboards succesfully.
|
|
|
hi i have s9 v4.21 hashboards ... pic ic need programmed where can i find pic hex file thanks
|
|
|
thanks. i want to test v9 hashboards with s9 t9 fixture........ i try but tester not recocnized v9 hashboards.... maybe we must tf card file chang.. i try with t9 tf card file to test v9 hashboards and s9 tf cards file to test v9 hashboards..... Should I change the file in the tf card for v9 miners?s thank
[...]
thanks my tester borads is v1.0 for s9 t9 not s11 s15 s17 i will attached some best pic from my test fixture Thanks for your honesty I fully understand what you mean What can I do now? I have tester files for s9 t9 model Now I need other files for v9 miner ,........... Can I contact you through WhatsApp or by email? Thanks again
|
|
|
What can I do to better understand the Hashboards Miner repairs?
[...]
thanks
|
|
|
Hi Thanks The device also tests other Bitmine products Like s11 s15 s17 Just change the file inside the tf card Then it can be tested
|
|
|
hi i have t1 16 th/s miner. can i use braiins frimware my miner control boards have not memory card socket.
|
|
|
HELLO i bought a Antminer Test Fixture for S9 T9+ i have tf card file for s9 t9 prducts i need tf file for s11 s15 s17 ,... can every one help me ?? http://uupload.ir/files/nenv_a1.jpg
|
|
|
|