 Show Posts
|
|
Pages: [1]
|
|
1
|
Bitcoin / Hardware / Re: [Guide] Dogie's Comprehensive Avalon Avalon2 Setup + Silencer Mod
|
on: April 09, 2014, 12:43:23 AM
|
We are getting close to compensation. I now can reach the "OpenWrt LuCI Authorization Required" web page. Username has root already typed in for it. I tried root for the password too and it did not work. Where can I find the password for my tplink tl-wr703n router? Do I have to do a reset? Thank you. Try password, admin, root and nothing. Or google, this information is out there. It was '123'. Now I can log in. I see more than 8 tabs to adjust settings. I also see a tab for cgminer configurations. I do not know how to adjust these settings. I have bfgminer, and I prefer to continue using bfgminer for mining bitcoin with the Avalon 2 units. Do you know how to configure these settings on OpenWrt Overivew LuCI or run bfgminer from the linux terminal with a command after I log in? Thank you. Seminer I thought you meant the emergency WRT page. Nevermind. Just enter your pool information into the cgminer page, that's all you have to do. No, you can't use BFGminer within WRT. Hey Dogie, I am still struggling. I am still having problems setting up my avalon 2 units. Do you know any references, forums, or other sources that can help me finish this configuration? I am using a Minepeon software with my raspberry pi. I log in, restart, and reboot the "miners." Under devices, it still says no devices running. I switched my 4 port usb hub with a 7 port usb hub. I don't know what is preventing me. Please help. Sincerely, Michael Scholz |
|
|
|
|
2
|
Bitcoin / Hardware / Re: Avalon2 Single Modular 55nm CGMiner or BFGMiner detection
|
on: March 29, 2014, 01:44:10 AM
|
Hi Xiangfu, This is seminer. I have been trying to set up my btc mining rig for 8 days now. Here is what I am working with: msi z77A-G45 motherboard (1 ethernet plugin) Do I put the ethernet cable in my century link router or in my one ethernet port on my motherboard? I do not have wireless internet on my desktop. 4 - Avalon 2 single modules (~105 Gh/s) 4-Corsair cx 430 power supply units (psu) 1 TPLINK WR703N router with power, usb, ethernet inputs... ip address sticker reads: 192.168.1.207 1 4-slot usb hub (to connect each usb cable off of the avalon 2 Linux Xubuntu 12.10 BFGMiner 3.2.0. 64bit cgminer 4.0.0. 64 bit (No experience with cgminer and linux terminal commands) openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-factory.bin -- What do i do with a bin file in linux terminal? When I connect to my tplink wr 703n router via ethernet which is connected to each of my four avalon 2 modules, i can connect to 192.168.1.207. I enter root for user and 123 for password and log in successfully. When I see the OpenWrt Overview LuCI webgui home page, there are more than eight tabs of configuration settings. I do not know how to get my Avalon 2 units mining. I want to configure bfgminer for these Avalon2 modules. I know some linux terminal commands to get a gpu mining. But now I need to learn some avalon asic linux terminal commands to get them going. I can not configure the router for mining. I also need to figure out my new terminal command to start the avalon 2 mining. I created an account with btcpoolman. Do you have any advice? Thank you. Seminer |
|
|
|
|
3
|
Bitcoin / Hardware / Re: [Guide] Dogie's Comprehensive Avalon Avalon2 Setup + Silencer Mod
|
on: March 29, 2014, 12:31:04 AM
|
We are getting close to compensation. I now can reach the "OpenWrt LuCI Authorization Required" web page. Username has root already typed in for it. I tried root for the password too and it did not work. Where can I find the password for my tplink tl-wr703n router? Do I have to do a reset? Thank you. Try password, admin, root and nothing. Or google, this information is out there. It was '123'. Now I can log in. I see more than 8 tabs to adjust settings. I also see a tab for cgminer configurations. I do not know how to adjust these settings. I have bfgminer, and I prefer to continue using bfgminer for mining bitcoin with the Avalon 2 units. Do you know how to configure these settings on OpenWrt Overivew LuCI or run bfgminer from the linux terminal with a command after I log in? Thank you. Seminer |
|
|
|
|
4
|
Bitcoin / Hardware / Re: [Guide] Dogie's Comprehensive Avalon Avalon2 Setup + Silencer Mod
|
on: March 27, 2014, 03:05:15 AM
|
Hey Dogie,
I do not know how to change my subnet on my router. I tried plugging in my ethernet cable from the WR to my desktop. In Ubuntu, I opened Network Connections. I double-clicked auto ethernet. I clicked the Ipv4 settings tab. For the method, I chose manual. I added an "ip address of 192.168.1.2, a netmask of 255.255.255.0, and gateway of 192.168.1.2. I clicked on Require IPV4 addressing for this connection to complete, and then hit save. I tried to go to 192.168.1.201 WR address in google chrome and firefox and could not connect. I tried it by not requiring IPV4 addressing for this connection to complete. I tried it after rebooting my computer. I tried it by reconnecting the ethernet cable to my router. I do not understand how the ip address, subnet, and gatway addresses work. Thanks for trying to help tho.
Sincerely,
Seminer
Gateway to the thing you're trying to connect to, ie 192.168.1.201 - that should do it. We are getting close to compensation. I now can reach the "OpenWrt LuCI Authorization Required" web page. Username has root already typed in for it. I tried root for the password too and it did not work. Where can I find the password for my tplink tl-wr703n router? Do I have to do a reset? Thank you. |
|
|
|
|
5
|
Bitcoin / Hardware / Re: [Guide] Dogie's Comprehensive Avalon Avalon2 Setup + Silencer Mod
|
on: March 25, 2014, 12:25:39 AM
|
Hey Dogie, this is seminer. I have been trying to set up my btc mining rig for 3 days now. Here is what I am working with: msi z77A-G45 motherboard (1 ethernet plugin) 4-Avalon 2 single modules (~105 Gh/s) 4-Corsair cx 430 power supply units (psu) 1 TPLINK WR703N router with power, usb, ethernet inputs... ip address sticker reads: 192.168.1.201 1 4-slot usb hub (to connect each usb cable off of the avalon 2 Linux Xubuntu 12.10 BFGMiner 3.2.0. 64bit cgminer 4.0.0. 64 bit openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-factory.bin I can not figure out how to set up the wr703N router. I can not connect to it. I type in http://192.168.0.100/ to google chrome browser and firefox browser and I get, "Oops! Google Chrome could not connect to 192.168.0.100" I can not get to the Openwrt admin login settings. I can not configure the router for mining. I also need to figure out my new terminal command to start the avalon 2 mining. Or, if I set them up to mine, what happens if my pc powers down? I need more details and troubleshooting than this information, https://bitcointalk.org/index.php?topic=493358I will compensate with useful help. Thank you. I have no idea why you have a motherboard, its nothing to do with that. It should be miners -> usb hub -> WR703N with WRT firmware. -> network cable to main router The address assumes you already have a modified WR, if you don't then go to the default IP of the WR (likely the sticker, 192.168.1.201). Then flash the WRT firmware on. THEN go to 192.168.0.100. Also remember that when you're trying to talk to different subnets, you'll need to change the subnet of your main router to match. Or, use 3)b) here http://www.dogiecoin.com/bitmain-antminer-s1.html with the last line changing to IP Address: 192.168.x.2, Subnet Mask: 255.255.255.0, Default Gateway: 192.168.y.y (x being the subnet you want and y.y being the subnet and ip you want to target to reach the WR). Hey Dogie, I do not know how to change my subnet on my router. I tried plugging in my ethernet cable from the WR to my desktop. In Ubuntu, I opened Network Connections. I double-clicked auto ethernet. I clicked the Ipv4 settings tab. For the method, I chose manual. I added an "ip address of 192.168.1.2, a netmask of 255.255.255.0, and gateway of 192.168.1.2. I clicked on Require IPV4 addressing for this connection to complete, and then hit save. I tried to go to 192.168.1.201 WR address in google chrome and firefox and could not connect. I tried it by not requiring IPV4 addressing for this connection to complete. I tried it after rebooting my computer. I tried it by reconnecting the ethernet cable to my router. I do not understand how the ip address, subnet, and gatway addresses work. Thanks for trying to help tho. Sincerely, Seminer |
|
|
|
|
6
|
Bitcoin / Hardware / Re: [Guide] Dogie's Comprehensive Avalon Avalon2 Setup + Silencer Mod
|
on: March 23, 2014, 06:34:29 PM
|
Everything is fine, leave it alone to mine now.
Hey Dogie, this is seminer. I have been trying to set up my btc mining rig for 3 days now. Here is what I am working with: msi z77A-G45 motherboard (1 ethernet plugin) 4-Avalon 2 single modules (~105 Gh/s) 4-Corsair cx 430 power supply units (psu) 1 TPLINK WR703N router with power, usb, ethernet inputs... ip address sticker reads: 192.168.1.201 1 4-slot usb hub (to connect each usb cable off of the avalon 2 Linux Xubuntu 12.10 BFGMiner 3.2.0. 64bit cgminer 4.0.0. 64 bit openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-factory.bin I can not figure out how to set up the wr703N router. I can not connect to it. I type in http://192.168.0.100/ to google chrome browser and firefox browser and I get, "Oops! Google Chrome could not connect to 192.168.0.100" I can not get to the Openwrt admin login settings. I can not configure the router for mining. I also need to figure out my new terminal command to start the avalon 2 mining. Or, if I set them up to mine, what happens if my pc powers down? I need more details and troubleshooting than this information, https://bitcointalk.org/index.php?topic=493358I will compensate with useful help. Thank you. |
|
|
|
|
