Latest posts of: whoami1

Show Posts
Pages: [1]

Local / Mining (Deutsch) / Re: Antminer S3 PROBLEM mit Strom :(

on: December 07, 2014, 11:05:50 PM

Nach einem Debug komme ich zwar fast drauf aber nicht ganz ;/

Wenn ich die IMG laden will:

Code:

Easy-Link> tftpboot

eth1 link down
dup 1 speed 100
*** Warning: no boot file name; using '0101A8C0.img'
Using eth0 device
TFTP from server 192.168.1.100; our IP address is 192.168.1.1
Filename '0101A8C0.img'.
Load address: 0x81000000
Loading: *.T T T T T T T T T T 
Retry count exceeded; starting again
eth1 link down
*** Warning: no boot file name; using '0101A8C0.img'
Using eth0 device
TFTP from server 192.168.1.100; our IP address is 192.168.1.1
Filename '0101A8C0.img'.
Load address: 0x81000000
Loading: *.T T T T T T T T T T 
Retry count exceeded; starting again
eth1 link down
*** Warning: no boot file name; using '0101A8C0.img'
Using eth0 device
TFTP from server 192.168.1.100; our IP address is 192.168.1.1
Filename '0101A8C0.img'.
Load address: 0x81000000
Loading: *.T T T T T T T T T T 
Retry count exceeded; starting again
eth1 link down
*** Warning: no boot file name; using '0101A8C0.img'
Using eth0 device
TFTP from server 192.168.1.100; our IP address is 192.168.1.1
Filename '0101A8C0.img'.
Load address: 0x81000000
Loading: *.T T T T T T T T T T 
Retry count exceeded; starting again
eth1 link down
*** Warning: no boot file name; using '0101A8C0.img'
Using eth0 device
TFTP from server 192.168.1.100; our IP address is 192.168.1.1
Filename '0101A8C0.img'.
Load address: 0x81000000
Loading: *.T T T 
Abort

frage: Wie kriege ich da über U-BOOT nun die neue Firmware rauf? welche befehle muss ich nehmen?

hier der gesamte Debug log: http://pastebin.com/z1aYCRkJ

Bitcoin / Hardware / Re: Announcement: Bitmain launches AntMiner solution, 0.68 J/GH on chip

on: December 01, 2014, 10:00:10 PM

Quote from: b00m3rang on November 24, 2014, 03:33:52 PM

I was having a problem with my AntMiner S3+ that had become unresponsive and inaccessible after I ticked a wrong check box while trying to get fancy with the network config. I was trying to connect the miner via WiFi, and also use it as an access point for my Raspberry Pi that's running a Gridseed, and I bridged the wrong two interfaces. I've seen a lot of posts in this thread with suggestions on how to fix it, but they are all either incorrect, incomplete, or unclear.

First off, no amount of fiddling with the reset button did anything at all, and I tried for many hours. Pressing the button once does nothing, holding it down for >10sec makes it restart as does double-clicking it, holding the button and then starting it up will just cause it not to boot. Someone said to start it, wait 3 minutes, hold the button for 15 seconds, do that again, and power cycle it... which didn't work, either.

I was able to fix it by connecting to the serial debugging port on the interface board with a USB to serial adapter, and editing the /etc/config/networking file with the correct settings and rebooting. The post that gave me the hint about the serial port was a little ambiguous on the TX/RX pinouts, so I wanted to post a pic that should be self-explanatory. I'm using a Parallax 'Propeller Plug' that I got for about $10 when I built a Propeller on a breadboard. The driver makes it show up as a regular COM port, and I used PuTTY under Windows to connect to it. The pin headers are just sitting in there, the worst that might happen with a loose connection is some corrupt characters in the terminal. The reset pin is not needed.

Hope it helps!

Hello,

my miner do not start because i try to update the firmware and the power was gone..
so now the miner start but only the red flash is flashing and i can not connect via LAN.

i try the debug ( thants for the pic, you are the only man in the internet that show this.. )

but i have problems whit my debug Sad

My Miner: Antminer S3

my result:

Start only Miner:

Code:

¦¦UI¦¦?1.1.4 (Apr 11 2013 - 01:45:00)

U-boot for ELink, build by huangfc(QQ:343669866)

Taobao:http://huangfc.taobao.com

model:ELink M150
DRAM:  64 MB
lE¦¦?¦¦¦¦on for 1s...
id read 0x100000ff
flash size 8388608, sector count = 128
Flash:  8 MB
U¦¦default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:ff:ff:ff
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:ff:ff:fe
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Autobooting in 1 seconds,Press p to stop autoboot!!
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.10.12 (xxl@ubuntu) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38031) ) #140 Mon Jul 21 17:27:04 CST 2014
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=TL-WR741ND-v4 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61336k/65536k available (2187k kernel code, 4200k reserved, 588k data, 232k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.100000] MIPS: machine is TP-LINK TL-WR741ND v4
[    0.100000] MAC FF:FF:FF:FF:FF:FF
[    0.100000] MAC 20:59:a0:c9:47:0e
[    0.560000] bio: create slab <bio-0> at 0
[    0.560000] Switching to clocksource MIPS
[    0.570000] NET: Registered protocol family 2
[    0.570000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.580000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.580000] TCP: Hash tables configured (established 512 bind 512)
[    0.590000] TCP: reno registered
[    0.590000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.600000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.610000] NET: Registered protocol family 1
[    0.630000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.630000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.640000] msgmni has been set to 119
[    0.650000] io scheduler noop registered
[    0.650000] io scheduler deadline registered (default)
[    0.650000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.660000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[    0.670000] console [ttyATH0] enabled, bootconsole disabled
[    0.670000] console [ttyATH0] enabled, bootconsole disabled
[    0.680000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[    0.690000] m25p80 spi0.0: unrecognized JEDEC id 014017
[    0.710000] libphy: ag71xx_mdio: probed
[    0.710000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[    1.260000] eth0: Found an AR7240/AR9330 built-in switch
[    2.300000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    2.850000] ag71xx ag71xx.0 eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    2.860000] TCP: cubic registered
[    2.860000] NET: Registered protocol family 17
[    2.870000] 8021q: 802.1Q VLAN Support v1.8
[    2.870000] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[    2.880000] Please append a correct "root=" boot option; here are the available partitions:
[    2.890000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
¦

thats all

and when i press the Reset button and start then i get:

Code:

¦

U-Boot 1.1.4 (Apr 11 2013 - 01:45:00)

U-boot for ELink, build by huangfc(QQ:343669866)

Taobao:http://huangfc.taobao.com

model:ELink M150
DRAM:  64 MB
led turning on for 1s...
id read 0x100000ff
flash size 8388608, sector count = 128
Flash:  8 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:ff:ff:ff
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:ff:ff:fe
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Enter Backup Mode...
eth1 link down
eth0 link down
eth1 link down
uip init...
http init...
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
eth1 link down
......

only this message Sad

what can i do, maybe u can help me??

3	Local / Mining (Deutsch) / Re: Antminer S3 PROBLEM mit Strom :(	on: November 25, 2014, 09:54:43 PM
für alle mit diesem Problem, ich habe es zwar noch nicht probiert, denke aber die Lösung gefunden zu haben. https://bitcointalk.org/index.php?topic=330665.msg9640895#msg9640895 Quote I was having a problem with my AntMiner S3+ that had become unresponsive and inaccessible after I ticked a wrong check box while trying to get fancy with the network config. I was trying to connect the miner via WiFi, and also use it as an access point for my Raspberry Pi that's running a Gridseed, and I bridged the wrong two interfaces. I've seen a lot of posts in this thread with suggestions on how to fix it, but they are all either incorrect, incomplete, or unclear. First off, no amount of fiddling with the reset button did anything at all, and I tried for many hours. Pressing the button once does nothing, holding it down for >10sec makes it restart as does double-clicking it, holding the button and then starting it up will just cause it not to boot. Someone said to start it, wait 3 minutes, hold the button for 15 seconds, do that again, and power cycle it... which didn't work, either. I was able to fix it by connecting to the serial debugging port on the interface board with a USB to serial adapter, and editing the /etc/config/networking file with the correct settings and rebooting. The post that gave me the hint about the serial port was a little ambiguous on the TX/RX pinouts, so I wanted to post a pic that should be self-explanatory. I'm using a Parallax 'Propeller Plug' that I got for about $10 when I built a Propeller on a breadboard. The driver makes it show up as a regular COM port, and I used PuTTY under Windows to connect to it. The pin headers are just sitting in there, the worst that might happen with a loose connection is some corrupt characters in the terminal. The reset pin is not needed. Hope it helps!

4	Local / Mining (Deutsch) / Re: Antminer S3 PROBLEM mit Strom :(	on: November 21, 2014, 02:02:59 PM
Das ist von einem S2, ich hab ein S3 da wird das so nicht gehen

5	Local / Mining (Deutsch) / Re: Antminer S3 PROBLEM mit Strom :(	on: November 11, 2014, 09:38:53 PM
Update: Habe ja 2 Antminer S3 hier. Habe nun beide auf gemacht, und die Platine die in der Mitte ist einfach mal ausgetauscht, sehe da nun läuft der andere mit der plantine von dem der vorher lief. also ist die eine Platine wohl beim Firmware Update kaputt geflasht worden... mir ist aufgefallen, das auf der Platine mehrere anschlüsse nicht genutzt werden, darunter "Debug" ist es möglich über die Anschlüsse etwas zu Reseten was der normale Reset nicht macht? oder Software mittels PC ein zu spielen? b.z Ist es möglich aus 2 Antiminer S3 einen zu machen? quasy 4 blöcke aber nur 1 platine zur steuerung?

6	Local / Mining (Deutsch) / Re: Antminer S3 PROBLEM mit Strom :(	on: November 09, 2014, 08:10:14 PM
hilft alles nichts. Schon reset probiert und alles, als die firmware abgebrochen hat, muss wohl was an der software stecken geblieben sein nur wie löse ich es...

7	Local / Mining (Deutsch) / Re: Antminer S3 PROBLEM mit Strom :(	on: November 08, 2014, 09:22:06 AM
Problem zum TEIL gelöst: 1: Der 2 Antminer läuft ohne Probleme nun. Lösung: AUCH wenn beim anschließen am anfang nur rot Blinkt, ist es nicht zu wenig Strom, er ist einfach noch nicht Configuriert. Ich habe nun den 2 Antminer am PC direkt angeschlossen wie von euch gesagt, die IP gesetzt und sehe da, er hat sich verbunden. 2: Der erste Antminer der beim Firmware Update vom vorbesitzer wohl vom Strom getrennt wurde, schaut da leider etwas anders aus. Verbindung mit Lan = Unidentifiziertes Netzwerk er erkennt zwar das da am Lan was angeschlossen ist, aber nicht was. Ist es möglich den Antminer komplett zu Reseten ( Hardreset ) ? Der Resetknopf am Antminer hilft da wenig, schon probiert.

8	Local / Mining (Deutsch) / Re: Antminer S3 PROBLEM mit Strom :(	on: November 08, 2014, 08:25:54 AM
delete plz

9	Bitcoin / Hardware / Re: ANTMINER S3 Discussion and Support Thread.	on: November 07, 2014, 08:56:52 PM
Quote from: mrc_spot on November 07, 2014, 06:31:21 AM Quote from: whoami1 on November 06, 2014, 07:34:33 PM Can someone help me? I became today my Antminer S3. i give him power and put lan cable insite. then power on. the fan works for 1-2 seconds, lan blinking red and green, then fan going out and the LED on the Lan is Blinking RED i can not go on 196.168.1.99 i can´t see the miner in my fritzbox. is not working:( what can i do? I was having same problem with my miner. Your miner is not fully powered up. Switch of the power supply & turn on after 5m, make sure your power supply is dedicate to this miner (i.e. one power supply for one miner) Repeat the above step with a gap of 5m until your miner is fully powered up. If you succeed than set the frequency to s3+ default & reboot. Make sure your miner is powered up for 2 days. This will fix the problem, if not than change the power supply. Please let me know if it worked for you. i try it, but now working THE PSN has now 530Watt is a Thermaltake Hamburg 530W u tell (i.e. one power supply for one miner) is this only 1 PCI E to 1 Miner ? and in witch plugin? if i do 1 insite ( Right site front of Lan ) then the miner start but the lan is not flashing if i do the 2nd in the left plugin, the miner stops the lan blinking red >_<

10	Local / Mining (Deutsch) / Re: Antminer S3 PROBLEM mit Strom :(	on: November 07, 2014, 08:19:26 PM
nein ganz sicher nicht wenn ich an den vorderen beiden strom steckern die stecker rein tuhe ( da wo lan vorne ist ) und lan anschließe und dann der miner kurz angeht sofort aber die lüfter stehen bleiben und die lan rot blinkt. ich sehe in der fritzbox ja ob an dem lan port was ist, - dort ist nichts in einem thread hier schreibt jemand: "I was having same problem with my miner. Your miner is not fully powered up. Switch of the power supply & turn on after 5m, make sure your power supply is dedicate to this miner (i.e. one power supply for one miner) Repeat the above step with a gap of 5m until your miner is fully powered up. If you succeed than set the frequency to s3+ default & reboot. Make sure your miner is powered up for 2 days. This will fix the problem, if not than change the power supply. Please let me know if it worked for you." Heißt das soviel wie ich soll den miner ausmachen, nach 5min anmachen dann wieder aus und dann wieder an immer mit 5min abstand bis es geht? und ich soll nur 1 strom stecker einstecken? ( wenn ja wo rein )

11	Local / Mining (Deutsch) / Re: Antminer S3 PROBLEM mit Strom :(	on: November 07, 2014, 06:58:20 PM
Ja, der kleine läuft dann super nur der S3 blint rot

12	Local / Mining (Deutsch) / Re: Antminer S3 PROBLEM mit Strom :(	on: November 07, 2014, 06:52:06 PM
Wie meinst du das? Das Thermaltake Netzteil mit 650watt hat 4 PCI E Anschlüsse, 2 davon hatte ich am S3 dran, eins am New Miner box, Die Miner Box ( zieht ca. 100Watt mit 100-100GhZ ) lief ohne probleme, die S3 dagegen haut nur rot blinkende LEDs raus

13	Local / Mining (Deutsch) / Antminer S3 PROBLEM mit Strom :(	on: November 07, 2014, 06:37:36 PM
Hi, Habe nun 2x Antiminer S3 hier stehen. bei beiden das selbe: Ich schließe an einem Gerät Strom an ( 2x PCI E ) und stecke lan rein. Starte und es dreht kurz der lüfter und am lan blinkt grün/rot nach 2 sekunden bleiben die lüfter stehen und es blinkt nur noch die Rote lampe. Laut anderen Foren und auch hier, wurde gesagt das es an zuwenig Strom liegt. Ich habe es nun mit einem Thermaltake Paris 650Watt probiert Thermaltake Hamburg 530Watt und sogar wie mir empfohlen wurde mal mit 2 Netzteilen es Probiert also beide angeschlossen jeweils 1x PCI E Immer das selbe. Phänomen: Schließe ich an der Vorderseite wo der Lan anschluss ist vorne Rechts ein Strom stecker an, startet der Miner, ist Extrem laut als ob er volle power dreht aber Lan bleibt ganz dunkel also weder rot noch grün leuchten. Es kann doch nicht sein das die Netzteile zu wenig Strom liefern?!??!?

14	Bitcoin / Hardware / Re: ANTMINER S3 Discussion and Support Thread.	on: November 06, 2014, 07:34:33 PM
Can someone help me? I became today my Antminer S3. i give him power and put lan cable insite. then power on. the fan works for 1-2 seconds, lan blinking red and green, then fan going out and the LED on the Lan is Blinking RED i can not go on 196.168.1.99 i can´t see the miner in my fritzbox. is not working:( what can i do?

Pages: [1]