I figured I would give an update on the build.....
This shows you what color goes to what wire.. and they are connected strait across on the PCB.

Just a quick side view

And a decent shot of the usb-uart and which color of wire goes to which spot. DO NOT FORGET  the 1 k ohm resistor from the 3.3v feed to the brown wire AKA RXD

I took my clock back down to --bet-clk 27
Full size link https://i.imgur.com/z570R82.png

And No I am sorry I have ZERO interest in doing a video on how this is made.. Mostly because I do not have another usb-uart to solder together, and I have no need to order another one unless some one wants me to modify one for them I can think of a couple ways to make it look so much prettier. You could clip the leads on the resistor and solder it directly from 3.3v to the RXD spot on the PCB. Use a PCB board that plugs directly into the usb-uart to the Tube/Prisma uart cable.

And better pictures of the usb-uart

The other end of the resistor is tied into the RXD line


And my sloppy way of connecting the uart to the tube...Yes I know looks bad. Will be picking up the parts I need to make an adapter after work.

I based this off the fact the maker of Asicminer Tubes/Prisma references the fact that the controller whether it is there premade usb-uart or a be-200 controller will control Tubes/Prismas daisy chained together, and that they can be chained together. If I have made a mistake and my educated assumption is wrong I will be more then happy to delete/modify this thread. Any one that owns a prisma feel free to chime in and let people know 100% one way or the other. I only own a tube I cannot afford a prisma.

Ha found a mistake with my power supplies.. after correcting them
And using 
./cgminer --bet-clk 30
to start cgminer


Check your power supply feed Right at the pci express connector at the hashing boards see what voltage you get. Mine were around 11.8* and was having one world of a time getting past 820 Ghs or so.. now 1.* Ths.
I opened my PSUs and adjusted them till I had 12.05 at the connecter UNDER LOAD and now im hashing perfectly at a good over clock.
New power draw running at 300 and getting around 1 Ths

And for those wondering this is what the cable ends look like on each PSU

Remember Set your voltage UNDER LOAD.

I am not responsible for damage done to ANYTHING. Always find out what pot needs to be turned which way it needs to be turned and GO SLOW.

Here is a link to a working setup using a random CP2102

https://bitcointalk.org/index.php?topic=865503.msg9597271#msg9597271

Have fun.

This is my current power usage It includes the odriod u3 cooling fans and Asicminer Tube.


And My Tube looks like this..

and

And these bad boys are how I power it all

Mods to make them work. Yes those wires go out to 4 pci express each. So 2 boards per psu.

They can be purchased for about $25 US off ebay
Part Number    438202-002
Product Type    Power Supply
Generation    DL580 G5/ BLc3000/ DL785 G5
Wattage    900W-1200W
Input Voltage     120-240 V AC
Hot Pluggable    Yes
Redundant    Yes
Auto Switching     Yes
Cooling    Active Fan
FAN    Internal
Other Part Number    437572-B21/ 438202-001/ 438202-002/ 440785-001/ 441830-001/ 438203-001/ HSTNSDL11
And a good pic of the tag..


And these for the PCI Express connectors
6-Pin Power Adapter Cable for PCI-Express - 10 inches
http://www.monoprice.com/Product?c_id=102&cp_id=10245&cs_id=1024503&p_id=2883&seq=1&format=2

You may find cheaper but I thought I found some good deals.

Yes resistor has to be there or its a no go..
And I'm trying to figure out how to post pics now.. LOL

BIG Thanks to novak@gekkoscience for pointing me in this direction.

I have my old Asic Tube working using a modified CP2102.. Here is what I did to help yall out. I Did this using Odruid U3 from hardkernal lets call it a beefier RPI. I have it running Ubuntu.
First off a special version of cgminer is needed..

sudo apt-get install build-essential autoconf automake libtool pkg-config libcurl3-dev libudev-dev

git clone https://github.com/blockerupter/cgminer.git

./autogen.sh CFLAGS="-O2 -Wall -march=native" –enable-blockerupter

make

./cgminer --bet-clk 27

You should be up and hashing after this. Of course the usual put in your pool and user info....

I will post pics of my sloppy setup.

This is the USB UART I used http://www.amazon.com/gp/product/B009T2ZR6W/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1
KEDSUM® CP2102 Module STC Download Cable USB 2.0 to TTL 6PIN Serial Converter For STC


And


Look at the hashrate averages.. The instant hashrate jumps around ALOT


And hey if this helps anyone A tip would be awsome  Bitcoin address to send to 16nP1WnxRdvbE64fqzyebx1eZnWdxdiPxp