And the winner is  10 Blocks in the last 12 hours...not bad! I have splitted my four S3 miner few weeks ago 2 at Eligius and 2 at Slush |
|
|
|
|
Ich habs nur mit einem Auge verfolgt, aber ich glaube im Mai.
|
|
|
|
Jo könnte fallen, aber spätestens wenn Bitmain liefert steigt sie wieder an  Eigentlich gut für alle (alte) Hardwarebesitzer, das die Entwicklung im Augenblick offensichtlich so langsam voran geht. |
|
|
|
Stats Stuck again ?.
Yepp seems down again |
|
|
|
Is the side down?
It was NOT my dog! But sure the cat from somebody else  Its up again here now and a block solved 1h ago |
|
|
|
Sure, we can add one to the settings page. Currently, If you dismiss an update message it should re-appear after 24 hours. You can also use the "Clear Cookies" button in settings and re-login. Those are the current workarounds  As for Slush, it's currently available in the Nightly update. Thanks! Tonight as I started the update message appears again and now I found the slush pool too  |
|
|
|
Can you put a button into settings to check manual for last updates ? 2 days ago I saw the new update message but finally I didn't push it! Yesterday after starting the soft I was waiting but nothing appears... Last question can you add "slush" to the Bitcoin pool list ? Thanks for the nice eyecandy soft |
|
|
|
|
I use two of the same Corsair PSUs to power my four S3's (no oc) without any prob
|
|
|
|
Estimated Position in Payout Queue
294.78065779 BTC are ahead in queue, putting this user's payout after a 11 block delay. Maybe end of the next week ?  |
|
|
|
|
The hashrate varies the last days and for the moment I couldn't reach the side anymore
|
|
|
|
Hättest Du vor deinem Post hier ein wenig im Forum gestöbert, wäre Deine Frage gar nicht gekommen Vergiss CPU und GPU Mining! Wenn Du Bewegung sehen möchtest, brauchst Du einen reinen ASIC Miner wie z.B. Antminer S3 oder S5 |
|
|
|
|
I don't have power meter on my own but what did your mate found out on your setup?
|
|
|
|
I would swallow all pills now only if we find a block  And 6 further more within the next 8 hours  |
|
|
|
By the way, I thought I would share my progress on my new mining closet built downstairs and offer details about the firmware updates and the advantages of getting your rig to the January 09, 2015 update to be able to under clock your S3 to make them more power efficient and to enjoy a much faster interface. I updated 13 S3+'s and 5 S3's with approximately 4 hard resets required during the whole process of updating them all.
I also have older S3's [5 of them]. They too have the most recent firmware upgrade to allow adjustment of the frequency and voltage. They average 370 GH/s at approximately .63 watts per GH/s. I thought I would save space by not posting a screen shot of them as well. Even your old S3's can be upgraded with the most recent firmware. You have to make sure you upgrade the one dated for August first. Then do the october update next and the January 2015 update last. If you try to go out of order, you may brick an old S3. If you get the following screen [screen shot below], do not panic. Just do a hard reset to factory defaults [entering in your pools, etc...] and pick up where you left off in the order of the updates. You may have to reboot once you're finished. If you get that same screen again after reboot [shown below] do not panic. Your old S3 should come back after a reset to factory settings.
Many thanks for sharing your experience dmwardjr, I have updated my 2 S3+ and my 2 S3 today to the newest firmware and copied your settings without any problems! Miners running nice quiet now in my garage and I will have a look at the power consumption tomorrow after 24h running. Have a nice evening (in Germany its 21.14 now) |
|
|
|
2 minutes after I put 4 new miners online we found the last block and now it lasts forever....nice present for me and my new miners Eligius  |
|
|
|
No Problem Sir, good thing needs time Looking forward to your release! |
|
|
|
|
Show Posts
