I have some coint listed as unexchanged since day's / Weeks
Any information when this will be fixed?
I like to com back to clevermining, it worked great in the past, but i like t make money and not "unexchanged" ;-)

will come back when clevermining works smooth again.

Best
Stonie

Is there something wrong with the pool?
I found a new "multipool" and like to compare it with clevermining.
The good thing i can split my miners, that i can run the 50% of my mining power to each pool, to compare.
but over the day Clevermining pool was often shown as dead in minera and so it switched to the fail over pool and i cant compare.

Hi,

I like to start also mining BTC direct.
does anyone knows a BTC- pool mybe like clevermining?

thanks for hints
Stonie

I have some additional miners in US which are located and mining to the us-URL
with the same user: 1JnmoLccUYafL7o2wcpb8y6PoB7kDz2D7H

will both collected to the same userID?
because i have two graphs, one for EU one for US on my userscreen, but the overview dont show the correct collected MHs for both locations.

will they be payed together?

Thanks
Stonie

Hi,
I use the Preconfigured miner options for

Minera 0.6.1
BFGminer 5.x (Official)

BFGminer Zeus miner+ Gridseed mixed

here the commandline i use:
--scrypt -S zus:all --set zus:chips=128 --set zus:clock=200 -S gridseed:all --set-device gridseed:clock=800

I use lower Clock then normal, because I changed the fan to low noise fans ;-)

For the setup, i dont know if this makes the "magic" that it runs ;-)
I first added the Zeusminer, after this was running fie i added the Gridseed.
My setup:

Raspberry Pi with minera 0.6.1
the Zeusminer Thunder is connected directly ti the PI
The two Gridseed Blade (4 boards) are connected to an powered D-Link Hub and the hub is connected to the PI.

hope that helps

Best
Stonie

OK, OK, my fault ;-)
you can ignore all I wrote about this ;-)

I don't know why, but in the past Minera versions i had trouble to get my miners running with BFGminer, badly the only one on the list who supports Gridseed and Zeus on the same rig.

I tested the setup now again with Minera 0.6.1 and now BFGminer works with both without any problem.

So all if fine now I have Zeus and Gridseed on the sam Raspbery Pi.

Thanks

Stonie

Hi,
I have currently two rigs running one is a raspberry PI2 with two Gridseed Blades and the secont is a Raspberry Pi2 with an Zeusminer Thunder.
I like to manage both over one PI.
means not to see both over the same webinterface, that means that Zeus and Gridseed miner are managed over the same Pi.

Can someone give me some hints how to configure this?


Thanks Stonie

Hi Terk, can you take a look,
seams like the daily payout is not working.

Best
Stonie

Hi,

I like minera, I have it running on two Raspberry PI 2 and it works fine.
i have some miners on each of them and sometimes i have to take one out for testing or something else.
I don't like to buy an third Raspberry only for testing, so here my question.

Is it possible to use the Raspberry Pi Image on a Notebook?
Why I'm asking:
I have a Windows Notebook and this should stay like it is, but for testing my miners, i like to boot from a SD Card Minera and do what i need to do for testing.

Ideas are welcome ;-)


Best
Stonie

He works currently with 750MH
So seams to be a kind of the bigger one.

You can easily check this on your own.
the BTC address is the username, so you can simply search for him in the user area.

Best
Stonie

Hi Terk,

thanks for your explanation.

this brings much more light in my darkness ;-)

I'm also more for the save way, but I'm far away from a professional to understand what happens behind the scenes.

So sorry for my questions ;-)

Hi Terk,
I had still no payout, but maybe it takes more time for the blockchain to sync.
But i have a lot of BTC in "Unexchanged" and they are not moving to "ready for payout" for nearly two days.
and as i remember this happens more often over a day in the past.
maybe you can take a look into this.

1JnmoLccUYafL7o2wcpb8y6PoB7kDz2D7H

and there is no hurry on my side, I think its better to wait a little bit then to loose something.

Best
Stonie

Thanks for feed back, Terk
Hopefully nothing critical happens what these maintenance requires.

Best
Stonie

same for me.
no payout for two days (11.July)
1JnmoLccUYafL7o2wcpb8y6PoB7kDz2D7H

Thanks for looking after ;-)

Stonie

is there any option to prevent this :

July 2, 2015 partial results after 12 hours: 0.000135 BTC/day per MH/s (35% LTC)

like if <90% (ideal <100%)  switch to LTC mining?

so the pool will always same or better then LTC ;-)

Best
Stonie

Only a question of interest.

Why are you killing your GPU with mining at 200Kh/s ?
I think if you like to mine, buy a small Zeusminer  like the Blizzard with 1.3Mh/s for round about 50 bugs on Ebay.
If you start this with a Raspberry Pi for mining, you have a much higher Hashrate, and you need much lower power.
And you don't kill your GPU;-)

only my two cent

Hi,

where can i download older versions of minera?
i have a lot of trouble with the new 0.6.0 version.
the main Problem for me is, that the poolhashrate is going down over the day to zero.
when i restart the miner  it went back to normal and after 30 mins ou can see that it starts going down step by step.
and also on the pool side the hashrate goes down the same way.

I was mining with Minera 0.4.0 without any problems sometimes over weeks.

My config:
Raspery Pi 2 with Gridseed Blade miner (40 Chips)

On the Minera0.4.0 Image I had additional two Gridseed mini miner and this worked without any problem.
On Miner 0.6.0 i got detection problems with this double configuration, the minera was not able to detect all miners.


Best
Stonie

Hi Terk,

thanks for this info.
hopefully these problems are solved and pool is back to normal now.

I had my miners switched back to Clevermining.

Best
Stonie

Hi J4abberwock,

are you still selling this hardware?

i'm interested in:
2x    DPS 2000-BB  Breakout board
10x  6 pins PCI-E cables 50cm long, 16AWG wires

should be shipped to Germany near Frankfurt.

Best
Stonie

Is there an answer possible to this "request restart" thing?
with the current settings: 100% LTC in the last 30 Days, 2% Fee, and wasting mining power because of restart requests, this pool is not really profitable instead of mining LTC directly.

even the fast answers here in the forum are not really a motivation ;-)

Best
Stone