S4?

Mhmmm indeed makes sense. So if the outlet is not sufficient enough (which I know it is not) I reckon I'd have to make some phone calls... Thxs JB

Model

Brand
    BELKIN

Series
    Home/Office

Model
    BE112230-08

Specification

Outlets
    12

Outlets Type
    Surge Suppressors

Cord Length
    8 Feet

Input Voltage
    125V

Output Amperage Capacity
    15

Output Watt Capacity
    1875 Watts

AC Suppression Joule Rating
    3780 Joules

EMI/RFI Noise Filter
    150K Hz ~100M Hz, up to 75dB

Clamping Voltage
    330 Volts

Unit Weight
    2.2

Features
    3780 Joule energy rating provides maximum protection of all your sensitive electronic devices

    12 Surge-protected outlets supply complete, 3-line AC protection

    8-foot power cord delivers optimal, safe AC power through a 14-gauge heavy-duty cord

    Filters EMI/RFI noise up to 75 dB reduction

    1-in, 2-out RJ11 Telephone/Fax Surge Protection

    Coaxial protection

    Right angle plug

    Simple detachable cord management system to help reduce cable clutter

    Covers each outlet with sliding safety covers




So would I be able to plug in say multiple 1300 watt PSU's http://www.newegg.com/Product/Product.aspx?Item=N82E16817182063&cm_re=1300_watt_power_supply-_-17-182-063-_-Product to it and have them run at full power? Does this output Watt Capacity of 1875 on the surge protector limit as such? And if so how would I plug in multiple 1300 watt PSU's into one place, What product would allow this? Electricity Costs will not be an issue for me (already calc'd)

Got it working im successfully mining my first coins through a different pool not BTCGuilds (I just input another pool type and it worked) I got a Rosewell 1000 Watt hooked up to 6 R-Boxes i have them at 325 Freq each doin 120gh/s, i havnt tried 330 i might later to see if i can get them all to reach 130 gh/s, but I might just nee a lil bit more juice from the PSU to reach 130 across all (iv tried 350 freq- 3 of the 6 were running at 130gh/s and the other 3 were about 110 gh/s, so thats when i decided to set freq to 325 to balance it out). Thxs for the help all!!!!! ))))))))) http://www.newegg.com/Product/Product.aspx?Item=N82E16817182188&cm_re=Rosewell_PSu-_-17-182-188-_-Product is what im using 38-40cs in temp all across the bored with 120gh/s ea

Noted Philipma I'll check it out for sure thanks!
Right now I just gotta figure out how to maintain connection to BTCguild's pool I have a feeling I might be typing something incorrectly and I know its not my BTC username mmmmmm......

I finally got it fixed with the Zadig on the Rockminers themselves then, i connected to BTCguild stratum- it was running fine for a few seconds possibly a minute and then it stopped taking shares from BTCstratum

Network Diff Changed to 47.9 G
Stratum connection to pool 0 interrupted
Pool 0 Stratum share submission failure
Pool 0 stratum+tcp://startum.btcguild.com:3333 not responding

This is what I got in my .bat:
cgminer --icarus-options 115200:1:1 -o stratum+tcp://stratum.btcguild.com:3333 -u BTCusername -p 12345 --rock-freq 350


I'm close to figurin this out

Alright I think I ruled out the hub because exchanged the rosewell with a 49 port Eyeboot hub and cg miner still giving me the above prompts

Ah okay, and I gathered more info on me problem.
 So basically its saying this over and over when using the rosewell 10 port hub

Blockerupter USB init failed
USB open device failed, err- 12
You need to install WinUSB driver for - BET Device 1:6
And associate - BET device 1:6 with WinUSB using zadig
See read me .TEXT for help
Blockerupter detect <1:6> failed to initialize <Incorrect Device?>

Blockerupter USB init failed
USB open device failed, err- 12
You need to install WinUSB driver for - BET Device 1:7
And associate - BET device 1:7 with WinUSB using zadig
See read me .TEXT for help
Blockerupter detect <1:7> failed to initialize <Incorrect Device?>


USB init, open device failed, err -12
You need to install WinUSB driver for - AMU Device 1:6
And associate - AMU device 1:6 with WinUSB using zadig
See read me .TEXT for help
Icarus detect <1:6> failed to initialize <Incorrect Device?>

USB init, open device failed, err -12
You need to install WinUSB driver for - AMU Device 1:7
And associate - AMU device 1:7 with WinUSB using zadig
See read me .TEXT for help
Icarus detect <1:7> failed to initialize <Incorrect Device?>

AMU prompt goes up to 1:9 (and i think the BAT one)

Alright success on connecting to the pool that Issue is over....Now the issue/question. What is a suitable USB HUB that can handle 6 rockminer Rboxes... because I tried this hub http://www.newegg.com/Product/Product.aspx?Item=N82E16817182208&cm_re=Rose_well_USB_hub-_-17-182-208-_-Product and CGminer was telling me to run Zadig on it to switch it to WinUSB...which i did then it just became totally undetectable and thereby useless. If i had to guess i would think that this particular hub isn't compatible with the WINusb driver software?!?!?

IF that is the mistake everything else checks out right?

Also to add when i started the cgminer exe it told me that the block erupter needed WINusb with Zadig/ Thing is i changed the software to that on a Rosewell 10port USB2.0 hub and then it said nothing was detected, so had to scrap that hub; and finally i could not connect to BTC guild wrong URL (Perhgaps I am inputting the info incorrectly possibly).

this is what i have
cgminer -o stratum.btcguild.com::3333 -u BTCusername -p BTCpass --rock-freq 350

I can't for the life of me get the bat file to start up with the latest cgminer software... tried all sorts of -o's and -p's


I have 6 R box Rockminers 110-130/Ghs each connected to my comp (which has internet via wifi) via USB and Powered by a 1000watt PSU
I'm using BTC guild as my pool
I want to control the freq of each miner ( i have made 6 worker names in BTC guild website) i.e. -Rock-Freq 350?
So....
What would I exactly type into the Notepad, that I would then save it as "StartMining.bat"  (any file)--save it to the cgminer folder then double click to run.

Halp!!!