 Show Posts
|
|
Pages: [1] 2 3 4 »
|
|
2 for me please.
will pay at late night.
|
|
|
|
sushi, what's the extra cost of UPS Express shipping?
i think you no need express, cuz 3~5 days the package will in you door step  |
|
|
|
ok CM 1200W gold, running 1 ant and 1 BFL 60GH, power meter show 11.95V, and other 2 ant with 1000W CM gold draw 740W power meter show 11.80V hashing very well, check all power cable all tight very tight. i thing not the power issue Ok... could be an issue. Make sure all your power is tight and you are supplying enough.
|
|
|
|
done many time, shut off wait for 30m and same, is hash 160~170GH Shut it down, wait a couple, reboot.
|
|
|
|
after hashing well few days or a week startup VVVVV  run 4m VVVVV  in chain 1 it show xxxxxxxx xxxxxoxo xoxoxoxo ooooooox RMA ? |
|
|
|
Is there a trick to getting the antminer to hold on to a reassigned static ip?
I go into the Network > Interfaces > Wan > and change the settings to an address on 192.168.1.x that is unassigned on my network, but when I hit save and apply it just hangs. I've tried a few different times now, waiting 2 min, 5 min, 10 min, and after plugging the cable back into the router, the miner hasn't been reassigned to the new address. I used the advance ip scanner utility and it still shows the same default address at 192.168.2.xx, which I can now not connect to either. After shorting the pins to do a hard reset, I can re-connect again on 192.168.2.99.
Any ideas?
you need to change you LAN before change the WAN LAN tab change to DHCP hit switch > save&apply . wait a bit then back to WAN tab change the ip that u want > save&apply |
|
|
|
try the steps and let us know.. https://github.com/AntMiner/AntGen1/blob/master/manual/AntMiner%20FAQ.pdf?raw=truehave you tried scanning your own miner? i had no issues reiping my miners... Just received my miner, but there is no sticker with the miners ip-address, how do i find it? Adjusted my own ip for the 192.168.2. range and tried opening 192.168.2.100 till 130 in my browsers but no response. The red light is on and the lan led is blinking so it seems it started.. but what now ?  Can't see any DHCP request on my router either, so it seems it's configured with static ip. change u subnet to 192.168.2.x then download http://www.advanced-ip-scanner.com/ and scan form 192.168.2.1 to 192.168.2.254 Yes i scanned and found that the same ip address that i had change, but still cant ping or connect or do anything, the miner just flashing the green led and the LAN led also flash green only (with no noise btw). If there any way to fully reset the control board to the factory setting? pls tell me T_T trying thank you !! @bclcjunkie is work i'm back to 192.168.2.99 and this FAQ just update an hour ago, thank you BITMAIN !! (i try the old ver of FAQ but it not work) this new one good thank you !!!! |
|
|
|
have you tried scanning your own miner? i had no issues reiping my miners... Just received my miner, but there is no sticker with the miners ip-address, how do i find it? Adjusted my own ip for the 192.168.2. range and tried opening 192.168.2.100 till 130 in my browsers but no response. The red light is on and the lan led is blinking so it seems it started.. but what now ? Can't see any DHCP request on my router either, so it seems it's configured with static ip. change u subnet to 192.168.2.x then download http://www.advanced-ip-scanner.com/ and scan form 192.168.2.1 to 192.168.2.254 Yes i scanned and found that the same ip address that i had change, but still cant ping or connect or do anything, the miner just flashing the green led and the LAN led also flash green only (with no noise btw). If there any way to fully reset the control board to the factory setting? pls tell me T_T |
|
|
|
@yuancraft you're my hero  Great app! The miner had 192.168.2.37.
u lucky guy and dont change ip address to subnet 192.168.1.x
or you will go to my situation
BITMAIN HELP |
|
|
|
Just received my miner, but there is no sticker with the miners ip-address, how do i find it? Adjusted my own ip for the 192.168.2. range and tried opening 192.168.2.100 till 130 in my browsers but no response. The red light is on and the lan led is blinking so it seems it started.. but what now ? Can't see any DHCP request on my router either, so it seems it's configured with static ip. change u subnet to 192.168.2.x then download http://www.advanced-ip-scanner.com/ and scan form 192.168.2.1 to 192.168.2.254 |
|
|
|
have you also changed your pc's ip to 192.168.1.x subnet? yes of course you need a same subnet to connect |
|
|
|
Just finished sending all of you the tracking number. I'm sorry for the delay.
SUSHI
lol !! sure? where mine number  sorry !!! just got email for you thank you !!! |
|
|
|
|
Transaction ID: db0ec14ee926c2590e956036f6e8c79206f16290c3b64c9139ac03ce15dcc88b
|
|
|
|
Fixed for missing the fixed price auction customers...
thank you for fixed up !! i'm paid right now !! |
|
|
|
6.oo BTC for 1 S1 x2? WOW BITMAIN is getting rich  |
|
|
|
|
